Scheduling Algorithms for Packet-Oriented MAC Protocols in Wireless Multimedia Systems

Future generation wireless multimediacommunications will require efficient Medium AccessControl (MAC) protocols able to guarantee suitable Qualityof Service (QoS) levels for different traffic classes whileachieving a high utilization of radio resources. This paperproposes a new scheduling technique to be adopted at the MAClevel in wireless access systems, named Dynamic Scheduling-Time DivisionDuplexing (DS-TDD), that efficiently managesvideo, voice, Web and background traffics. A theoretical approachis proposed in this paper to evaluate the DS-TDD performance withvoice and Web traffics. Simulation results have permitted tohighlight the following promising characteristics of the DS-TDDscheme: (i) a high capacity of real-time traffics isattained with a QoS insensitive to Web and background trafficloads; (ii) a high throughput can be guaranteed whilepreserving the QoS levels of the different traffic classes;(iii) heavier downlink traffic loads do not modify the QoSof uplink traffics. Finally, extensive comparisons with differentscheduling schemes proposed in the literature have permitted tohighlight the better performanceof DS-TDD.     

高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Analysis of Multiphase Flow and Heat Transfer: Pressure Buildup in an Unsaturated Porous Slab Exposed to Hot Gas

This study develops a mathematical model for coupled heat and mass transfer in an unsaturated porous slab exposed to a flowing hot gas. Effects of the initial saturation conditions on associated variables, i.e., total pressure, temperature, moisture content, and multiphase flow, are studied. The Newton-Raphson method based on a finite volume technique is applied. This study emphasizes the influence of initial saturation level and gravitational effect in heat and multiphase flow phenomena associated with this system. Gravity enhances the downward flow of liquid within the porous slab. Pressure buildup occurs near the interface between the wet and the dry zone. However, it appears that the order of magnitude to the total pressure is small. This study explains the fundamental mechanism of multiphase flow that involves heat and mass transfer in a heated unsaturated porous slab.     

在线磨辊辊面粗糙度的实验研究

影响轧辊表面粗糙度的因素很多，为此对影响辊面粗糙度的因素进行了系统分析和实验研究，得出了轧辊和砂轮的速度、砂轮粒度、砂轮直径及磨削液等主要因素对轧辊表面粗糙度影响的一般规律。利用回归分析的方法建立了轧辊表面粗糙度的数学模型，并将计算值与实测值进行了比较，发现两者基本一致。此项研究为适时控制冷轧带钢在线磨辊辊面粗糙度提供了计算模型。     

1 000 t/d湿磨干烧生产线工艺特点和调试

湿法生产线的技术更新改造有异地新建新型干法生产线和原地改成湿磨干法生产线二种。浙江虎山集团(?)3.0 m×88.68 m湿法线的改造,经方案比较和生产原料的状况,采用了湿磨干烧方案。其中,料浆脱水采用了真空吸滤法,浇成系统采用了南京院专有技术。改造投产后,获得了优质、高产、低耗和安全生产的技改效果。     

FLOW OF NEWTONIAN FLUIDS THROUGH SINUSOID ALLY CONSTRICTED TUBES. NUMERICAL AND EXPERIMENTAL RESULTS

Numerical and experimental predictions of pressure drops in the flow of Newtonian fluids through sinusoidally constricted tubes (SCT) are carried out. The numerical evaluations analyzed in this work are obtained from the following methods: Geometric Iteration (GJM), Geometric Iteration with First and Second Upwinds (GIM1, GIM2), Successive Over Relaxation by Line (SORBLM), Global Galerkin Spectral Method (GGSM), Collocation (CM) and Dufort-Frankel (DFM). The GIM1, GIM2 and SORBLM are applied to SCT and explained in this work. The other methods have been previously reported in the literature with the same purpose. Experiments are accomplished for constrictions of approximately 40,60 and 80% of the average tube diameter and results compare well with numerical predictions of the steady flow. It is concluded that special attention should be given to evaluations of the friction factor ƒ for Reynolds numbers Re between the onsets of flow separation and turbulence due to flow instability. Finally, the SCT as a model for porous media (PM) is discussed.     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

Modified oil agglomeration process for coal beneficiation. III. Grinding and agglomeration using different szego mill designs

The simultaneous grinding/agglormeration process has been used to beneficiate Minto coal. Experiments with the Szego Mill, a planetary ring-roller mill with grooved rollers, have given good results. Different roller ridge/groove sizes have been tested and favourable oil-coal-water ratios established. Ash removal is closely related to grinding performance. Very short mill residence times, of the order of 10 seconds, are sufficient for microagglomerate formation. Considerable equipment and operating cost savings are possible with the modified process.