Influence of high energy ball milling on structural,microstructural and optical properties of TiO2 nanoparticles

The influence of high-energy ball milling on structural, microstructural, and optical properties of TiO₂ by modifying the nanoparticle size was studied. Five samples were extracted at different milling times (0, 2, 4, 8, and 13 h). The average particle sizes estimated by dynamic light scattering (DLS) were 205, 155.8, 116.8, 82.9, and 82.7 nm at 0, 2, 4, 8, and 13 h, respectively. X-ray diffraction analysis confirmed progressive broadening of the peaks as the milling time elapsed. Besides, a correlation was found between d spacing and the average crystal size. The UV–Vis diffuse reflectance spectra of TiO₂ revealed a decrease in reflectance due to particle size reduction. Similarly, an alteration of the bandgap transition energy was presented, whose values gradually decreased from 2.966 eV to 2.861 eV for the sample without and with the maximum duration milling performed (13 h), respectively. Likewise, the SEM analysis showed a distribution in nanoparticle size that became more homogeneous and smaller average grain size as the milling duration was longer.     

Memory-based dynamic event-triggered control for networked interval type-2 fuzzy systems subject to DoS attacks

In this article, the memory-based dynamic event-triggered controller design issue is investigated for networked interval type-2 (IT2) fuzzy systems under non-periodic denial-of-service (DoS) attacks. For saving limited network bandwidth, a novel memory-based dynamic event-triggered mechanism (DETM) is proposed to schedule data communication. Unlike existing event-triggered generators, the developed memory-based DETM can utilize a series of newly released signals and further save network resources by introducing interval dynamic variables. Moreover, to improve design flexibility, an IT2 fuzzy controller with freely selectable fuzzy rule number and premise membership functions (MFs) is synthesized. Then, a new switched time-delay system with imperfectly matched MFs is established under the consideration of memory-based DETM and DoS attacks simultaneously. Besides, based on the property of MFs, the boundary information of membership grades and slack matrices are introduced in the stability analysis. Furthermore, by using a piecewise Lyapunov–Krasovskii method, membership-functions-dependent criteria are deduced to ensure the asymptotic stability of built fuzzy switched systems. Finally, the effectiveness of proposed control strategies is demonstrated by simulation examples.     

Physical and electrochemical behavior of affordable Na3SbS4 solid electrolyte at different heat treatment temperatures

High-capacity and affordable all-solid-state Na-ion batteries have gathered increasing interest in recent years owing to low-cost sodium, which contributes to reducing the price of these Na-ion batteries to approximately 70% of that in lithium batteries. However, in terms of electrolyte performance and battery cost, the complete replacement of lithium batteries has a long way to go. In this work, low-cost and high-safety Na₂S·9H₂O materials are used in synthesizing Na₃SbS₄ solid electrolyte, the price of which is only one-fifth that of high-purity Na₂S. The structure and electrochemical properties are studied through X-ray diffraction analysis, Raman spectroscopy, scanning electron microscopy, and electrochemical tests. Results indicate that a multiphase Na₃SbS₄ structure containing cubic and tetragonal phases formed after heat treatment at 300 °C. In addition, a third phase transition of Na₃SbS₄ is inferred after further heating at 600 °C. This phase structure contributes to the improvement of electrochemical performance by promoting increasing ionic conductivity to 0.54 mS cm^?1 at room temperature (25 °C) and reducing activation energy to 0.076 eV. This work provides an affordable material with good electrochemical properties and not only simplifies the preparation but also greatly reduces the risk of the process.     

An interval observer for uncertain continuous‐time linear systems

To design robust interval observers for uncertain continuous‐time linear systems, a new set‐integration approach is proposed to compute trajectory tubes for the estimation error. Because this approach, the order‐preserving condition on the dynamics of the estimation error is no longer required. Therefore, synthesis methods can be used to compute observer gains that reduce the impact of the system uncertainties on the accuracy of the estimated state enclosures. The performance of the proposed approach is showcased through illustrative numerical examples.     

溢流型球磨机进料口密封装置的改进

分析了溢流型球磨机进料口矿浆泄漏的原因以及泄漏后给球磨机润滑系统和环境所带来的危害。通过对溢流型球磨机进料口密封装置的改进,减少和杜绝了矿浆泄漏,改善了球磨机运行环境,延长了润滑油使用周期、提高了球磨机有效作业率,降低了球磨机运行成本。     

Preparation of YSZ porous ceramics with precise porosity control

Conventional preparation of porous ceramics often hard to accurately control the porosity of the samples. In this paper, by improving the foaming method, the foaming process is placed in the limited space of the ball mill tank, and YSZ porous ceramics with different porosity are obtained by changing the amount of slurry. Initial results showed that the porosity of the sample varies linearly with the increasing of addition of slurry. From the microscopic morphology, it can be seen that the increase in slurry content will reduce the number of pore with little changed size, which lead to the decrease in porosity. Therefore, with simple calculation YSZ porous ceramics with 85%, 80%, 75%, 70%, and 65% porosity can be obtained using the method of foaming in limited space by ball milling.     

甲基氯硅烷精馏流程的模拟与优化

采用Aspen plus软件对工业七塔精馏过程进行全流程建模与模拟，优化工艺参数，研究了新的精馏节能工艺。对一甲塔等7个精馏塔采用双因素水平的灵敏度分析，考察了塔釜采出率、回流比、进料位置和塔顶压力对产品浓度和热负荷的影响，确定一甲塔最优的工艺参数：塔釜摩尔采出率为0.92，摩尔回流比为130，塔顶压力为0.18 MPa，总理论板数为400，在210块理论板位置进料。在此基础上，针对高能耗的脱高塔/脱低塔，模拟研究了双效精馏新工艺，新工艺可节省39.70%的年总成本；针对一甲塔模拟研究了热泵精馏新工艺，新工艺可降低41.42%的年总成本。     

自旋对角接触球轴承弹流润滑与油膜刚度的影响

根据角接触球轴承自旋运动特征，同时考虑弹流润滑效应，建立角接触球轴承考虑自旋运动的弹流润滑模型；采用多重网格法求解弹性变形，利用有限差分法迭代求解雷诺方程，得到较为精确的数值解；分析不同赫兹接触压力、滚道表面粗糙度下自旋对角接触球轴承弹流润滑和油膜刚度的影响。结果表明：考虑自旋时随着Hertz接触压力、自旋角速度增大，油膜厚度减小，油膜压力增大，油膜承压区域呈细长状，并向接触中心靠近；随着滚道表面粗糙度幅值增大，油膜压力和膜厚均出现了波动，且考虑自旋运动时，轴承油膜厚度明显减小，油膜局部压力峰值更大；随着卷吸速度、润滑油黏度增大，油膜刚度减小，而考虑自旋运动时油膜刚度值更大；随着自旋角速度增大，油膜刚度逐渐增大。     

Visually deficient working conditions and reduced work performance in office workers: Is it mediated by visual discomfort?

IntroductionThe main purpose of this cross-sectional study was to investigate whether visual discomfort acts as a mediating factor between perceived visual ergonomic working conditions and self-rated visual performance among office workers who carry out administrative tasks and computer-based work at the Swedish Tax Agency.MethodsA questionnaire was sent to 94 office workers addressing: 1) perceived visual quality of the visual display units; 2) prevalence of eye symptoms; and 3) self-rated visual performance. Eighty-six persons (54 women (63%), 31 men (36%), and 1 of unspecified sex) answered the questionnaire. Multiple regression analysis investigated the association between visual ergonomic working conditions and visual performance, both with and without visual discomfort as a mediator.ResultsThe group mean of the Indexed survey questions indicated a reasonably good quality of visual ergonomic working conditions, a relative absence of eye symptoms, and acceptable self-rated visual performance. Results from multiple regression analysis showed a significant association between perceived visual ergonomic working conditions and self-rated visual performance (r² = 0.30, β = 0.327, p < 0.01). When visual discomfort was used as a mediator, the association between perceived visual ergonomic working conditions and self-rated visual performance remained the same (r² = 0.32, β = 0.315, p < 0.01).DiscussionIt was remarkable to discover that self-rated visual performance was independent of visual discomfort. Possible explanations include exposure factors not included in the current study, such as dry air and sensory irritation in the eyes, psychosocial stress, time spent performing near work activities, or time exposed to visually deficient working conditions.Relevance to industryThe strong connection between satisfaction with visual ergonomic working conditions and productivity in this study has implications for workplace profitability and staff satisfaction. If productivity is enhanced by better visual ergonomic working conditions, then managers of workplaces may be able to improve work outcomes by optimizing the physical work environment.