Toughness and R-curve behaviour of laminated Si3N4/SiCw ceramics

Laminated Si₃N₄/SiC_w ceramics were successfully prepared by tape casting and hot-pressing. Its mechanical properties were measured and the impact resistance was discussed. The toughness of the laminated Si₃N₄/SiC_w ceramics was 13.5 MPa m^1/2, which was almost 1.6 times that of Si₃N₄/SiC_w composite ceramics, namely 8.5 MPa m^1/2. Moreover, the indentation strength of laminated Si₃N₄/SiC_w ceramics was not sensitive to increasing indentation loads and exhibited a rising R-curve behaviour, indicating that the laminated Si₃N₄/SiC_w ceramics had excellent impact resistance. The improved toughness and impact resistance of laminated Si₃N₄/SiC_w ceramics was attributed to the residual stress caused by a thermal expansion coefficient mismatch between the different layers, resulting in crack deflection and bridging of SiC whiskers in the interface layer, thus consuming a large amount of fracture work.     

Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.     

Simple and novel synthesis of zirconia whiskers from a phosphate flux

High quality zirconia whiskers have been successfully prepared by molten salt method, using zirconium oxychloride (ZrOCl₂·8H₂O) and sodium phosphate tribasic dodecahydrate (Na₃PO₄·12H₂O) as precursor and molten salt, respectively. The effects of types of molten salt and heat treatment temperature on the formation of zirconia whiskers were characterized by XRD, Raman, DTA-TG, FE-SEM, TEM, SAED and HR-TEM. When Na₃PO₄·12H₂O is utilized as molten salt and the heat treatment temperature is 900?°C, the as-prepared zirconia whiskers with length ranging from 4?µm to 8?µm show an average aspect ratio of 25. The obtained ZrO₂ whiskers with monoclinic structure are elongated along [010] direction and exhibit a smooth surface with no distinct defects. The XRD and Raman results reveal that the phase transformation from tetragonal zirconia to monoclinic zirconia occurs with the increased crystal size and the water quenching treatment can significantly reduce the content of sodium zirconium phosphate [Na_9–4×Zr_x(PO₄)₃] in the final product. The growth mechanism of zirconia whiskers is supposed to be a dissolution-precipitation process. Since the sodium zirconium phosphate [Na_9–4×Zr_x(PO₄)₃] effectively promotes the dissolution of zirconia in liquid molten salt, zirconia can grow into zirconia whiskers according to its anisotropy.     

Aluminum to germanium inversion in mullite-type RAlGeO5: Characterization of a rare phenomenon for R = Y,Sm–Lu

Mullite-type RMn₂O₅ (R = Y, rare-earth element) ceramics are of ongoing research attentions because of their interesting crystal-chemical, physical, and thermal properties. We report a detailed structural, spectroscopic and thermal analysis of the series of mullite-type RAlGeO₅ (R = Y, Sm-Lu) phases. Polycrystalline samples are prepared by solid-state synthesis methods. Each sample is characterized by X-ray powder diffraction followed by Rietveld refinements, showing that they are isotypic and crystallize in the space group Pbam. The change of the metric parameters is explained in term of the lanthanide contraction effect. A rare inversion of Al/Ge between octahedral and pyramidal sites have been observed for these mullite-type so called O10 compounds, and the inversion parameter found to be between 0.22(1) and 0.30(1) for different R-cations. The <Al/Ge–O> bond distances and their bond valence sums (BVSs) support the respective inversions. Density functional theory (DFT) calculated phonon density of states (PDOS) and electronic band structures are compared for the vibrational and electronic band gap features respectively. Analysis of UV/Vis absorption spectra using both derivation of absorption spectra fitting (DASF) and Tauc's methods demonstrates that each of the RAlGeO₅ O10 compounds is high bandgap semiconductor, possessing direct transition between 4.1(1) and 5.4(1) eV. Both Raman and Fourier transform infrared spectra show clear red shift (quasi-harmonic) of the vibrational wavenumbers with respect to the ionic radii of the R-cations. Selective Raman bands at higher wavenumber region further complement the inversion of Al/Ge between two coordination sites. The higher decomposition temperature of the RAlGeO₅ compounds, compared to those of RMn₂O₅ phases, is explained in terms of higher bond strength of Al/Ge-O than those of Mn-O. Irrespective to the inversion between Al- and Ge-sites, the decomposition temperature also depends on the type of R-cation in RAlGeO₅.     

The toughening design of multi-layer antioxidation coating on C/C matrix via SiC-SiCw transition layer grown in-situ

Poor antioxidant and thermal-shock capacities of C/C composites thermal barrier coating (TBC) caused by cracking and shedding of coatings has been a major obstacle blocking the development of C/C composites. Herein, in-situ growth of whisker reinforced silicon carbide transition layer and inter-embedding mechanism of multi-gradient coatings were brought into the design of TBC to enhance the antioxidant and thermal-shock capacities. A three-layer gradient coating SiC-SiC_w/ZrB₂-SiC/ZrSiO₄-aluminosilicate glass (ZAG) from inside to outside, in which ZrB₂-SiC/ZAG serve as oxygen barrier layers with self-healing ability and SiC-SiC_w provides thermal stress buffering and bonding against cracking and shedding of coatings, is designed. The ZAG mainly forms a dense oxygen blocking frontier with self-healing ability through fluidized glass, while the ZrB₂-SiC can react actively with infiltrated oxygen in a way of self-sacrifice, preventing oxygen erosion to C/C matrix and SiC-SiC_w transition layer. As a result, the collaborative work among layers endows this coating with excellent high temperature service performance. This work provides a new insight for the design of excellent TBC.     

Transient liquid phase diffusion process for porous mullite ceramics with excellent mechanical properties

Porous mullite ceramics were fabricated by the transient liquid phase diffusion process, using quartz and fly-ash floating bead (FABA) particles and corundum fines as starting materials. The effects of sintering temperatures on the evolution of phase composition and microstructure, linear shrinkage, porosity and compressive strength of ceramics were investigated. It is found that a large amount of quartz and FABA particles can be transformed into SiO₂-rich liquid phase during the sintering process, and the liquid phase is transient in the Al₂O₃-SiO₂ system, which can accelerate the mullitization rate and promote the growth of mullite grains. A large number of closed pores in the mullite ceramics are formed due to the transient liquid phase diffusion at elevated temperatures. The porous mullite ceramics with high closed porosity (about 30%) and excellent compressive strength (maximum 105?MPa) have been obtained after fried at 1700?°C.     

Preparation of in situ grown silicon carbide whiskers onto graphite for application in Al2O3-C refractories

C-SiC composite powders were prepared by salt-assisted synthesis from Si powders, graphite, and a molten salt medium (NaCl and NaF) with the molar ratio of Si/C =?1/2 at 1300?°C for 3?h. After the C-SiC composite powders part and complete replacement of the graphite, the mechanical properties, oxidation resistance and slag-corrosion resistance of the Al₂O₃-C materials were studied by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS), as well as with dedicated equipment. The results indicated that SiC whiskers, with lengths of 10–50?nm, formed on the surface of the flake graphite, and the activation energy of oxidation of the C-SiC composite powder increased by 45.72?kJ?mol^?1 as compared to that of flake graphite. Furthermore, the decarburization area and slag erosion area of the Al₂O₃-C material decreased after 3?wt% of C-SiC composite powder was substituted for the flake graphite. Meanwhile, the cold modulus of rupture was maintained when 3?wt% of C-SiC composite powder was added. This improved both the oxidation and slag resistance of the Al₂O₃-C materials.     

Effects of Al2O3 crystal types on morphologies,formation mechanisms of mullite and properties of porous mullite ceramics based on kyanite

Porous mullite ceramics with different crystal shapes of mullite are fabricated by in-situ reaction with middle-grade kyanite as raw material, Al(OH)₃, γ-Al₂O₃, ρ-Al₂O₃ and α-Al₂O₃ as alumina sources. Effects of Al₂O₃ crystal types on morphology evolution and formation mechanisms of mullite, and properties of porous ceramics are investigated. Results show that mullite in the sample with Al(OH)₃ mainly shows acicular morphology, because its (001) plane has the minimum interplanar crystal spacing and maximal attachment energy, it grows fast along [001] direction by screw dislocation mechanism. With a successive slowdown in reactivities of Al(OH)₃, γ-Al₂O₃, ρ-Al₂O₃ and α-Al₂O₃, the amount and aspect ratio of mullite reduce, its growth mechanism gradually transforms into two-dimensional nucleation. Acicular mullite not only reinforces samples, but makes effective pore sizes smaller, which enable the sample with Al(OH)₃ to present low bulk density, high apparent porosity and linear changes, small average pore size and good mechanical strength.     

Mullite-bonded SiC-whisker-reinforced SiC matrix composites: Preparation,characterization, and toughening mechanisms

A novel mullite-bonded SiC-whisker-reinforced SiC matrix composite (SiCw/SiC, SiC whisker-to-SiC powder mass ratio of 1:9) was designed and successfully prepared. Before preparing the composite, the inexpensive lab-made SiCw was first modified by an oxidation/leaching process and then coated with Al₂O₃. The kinetics results indicate that the oxidation process can be described by improved shrinking-cylinder models. The aspect ratio of SiCw improved after modification. Subsequently, raw materials with a SiC–SiO₂–Al₂O₃ triple-layered structure were obtained after the Al₂O₃-coating process and used as feedstocks during the subsequent hot-pressing sintering. Finally, the characterization of the composites indicates that the mullite-bonded sample performs better (relative density of 93.8?±?1.4%, flexural strength of 533.3?±?18.2?MPa, fracture toughness of 13.6?±?2.1?MPa?m^1/2, and Vickers hardness of 20.6?±?2.5?GPa) than the reference sample without the mullite interface. The improved toughness could essentially be attributed to the moderately strong interface bonding and effective load transfer effects of the mullite interface.     

Preparation of Al2O3-mullite thermal insulation materials with AlF3 and SiC as aids by microwave sintering

Al₂O₃-mullite composites were prepared under the synergy effect of AlF₃ and SiC aids by microwave heating. The phase composition, microstructure, porosity, flexural strength, thermal shock resistance, and thermal conductivity were investigated. The XRD results revealed that the content of mullite phase steadily increased with the increasing of AlF₃ content. The microstructure showed that the lower content (≤1 wt%) of AlF₃ led to the formation of granular mullite and the higher content (≥3 wt%) of AlF₃ led to the formation of mullite whiskers, which could form an interlocking structure. In addition, the SiC hot spots can also promote the generation of mullite whiskers by microwave sintering. The thermal shock resistance was significantly improved by the interlocking structure of mullite whiskers. The residual rate of flexural strength of the composite with 3 wt% AlF₃ was 86%. The composite with 3 wt% AlF₃ additives got its optimized thermal conductivity from 30°C to 950°C, the value was between 0.819 and 1.021 W/(mK), which possess excellent thermal insulation performance.