新型限力输出保护功能柔性夹钳的设计与参数评估

柔性夹钳因具有微/纳精密操作能力, 常应用于微操作系统中, 但因抓爪无法提供恒定输出力或恒力范围小, 容易造成操作对象的损伤或脱落。根据放大模块与常力模块串联的结构形式, 设计了一种具有常力特性的柔性夹钳。基于伪刚体法, 建立放大模块中桥式机构与杠杆机构的刚度和放大率数学模型, 通过对倾斜导向梁进行分析, 得到常力模块的力-位移关系式, 计算出恒定输出力为42.5 N, 输出范围为370 μm。最后, 结合不同柔顺梁的结构参数, 运用MATLAB仿真探究了各关键参数对常力特性的影响。研究结果可为常力柔性夹钳的构型设计和分析提供一定的理论支撑。     

Radiation and slip effects on MHD Maxwell nanofluid flow over an inclined surface with chemical reaction

The numerical solutions of the upper-convected Maxwell (UCM) nanofluid flow under the magnetic field effects over an inclined stretching sheet has been worked out. This model has the tendency to elaborate on the characteristics of “relaxation time” for the fluid flow. Special consideration has been given to the impact of nonlinear velocity slip, thermal radiation and heat generation. To study the heat transfer, the modified Fourier and Fick's laws are incorporated in the modeling process. The mass transfer phenomenon is investigated under the effects of chemical reaction, Brownian motion and thermophoresis. With the aid of the similarity transformations, the governing equations in the ordinary differential form are determined and then solved through the MATLAB's package “bvp4c” numerically. This study also brings into the spotlight such crucial physical parameters, which are inevitable for describing the flow and heat transfer behavior. This has been done through graphs and tables with as much precision and exactitude as is possible. The ascending values of the magnetic parameter, the Maxwell parameter and the angle of the inclined stretching sheet cause decay in the dimensionless velocity while an assisting behavior of the thermal and concentration buoyancy parameters is noticed.     

水平斜插板透空式防波堤消波性能数值模拟

通过改进已有的防波堤模型，建立了一种新型水平斜板透空式防波堤模型。基于VOF方法建立了波浪与水平斜板防波堤相互作用的数值模型。经数值模拟研究了该新型水平斜板防波堤结构对波浪透射系数的影响，主要考虑了斜板角度、波陡、相对板间距、相对板宽和相对出水高度等因素对防波堤消波效果的影响。模拟结果显示:①水平斜插板透空式防波堤比水平板透空式防波堤的消波效果好。在斜插板作用下，随着斜板角度增大，透射系数逐渐增大，但增幅逐渐减小；②随着波陡增大，透射系数先减后增；③随着水平板间距增加，透射系数增大；④随着防波堤相对板宽的增大，透射系数逐渐减小；⑤随着防波堤出水高度增加，透射系数先减后增。结果表明，该新型结构防波堤的消波效果显著，可以很好地消减波浪，应用前景良好。     

厌氧接触+射流曝气+Fenton流化床技术处理制浆造纸废水运行实例

介绍厌氧接触+射流曝气+Fenton流化床技术处理制浆造纸生产废水的工程参数、运行效果和工程效益。六个月的运行数据显示,厌氧单元出水COD平均浓度为1321 mg·L^-1,平均去除率为61%;好氧单元出水COD浓度为185 mg·L^-1左右,平均去除率为78%;深度处理部分COD出水浓度为44 mg·L^-1,平均去除率为73%,可实现废水达标排放。     

复杂型急倾斜煤层的开采技术探析

中国煤炭资源多处于中厚煤层中,伴随煤炭资源的不断开采,矿井深度日渐增加,煤层的开采环境也日渐复杂,其中复杂型急倾斜煤层对开采技术和开采施工工艺水平的要求较为突出。课题基于中国复杂型急倾斜煤层开发工艺的现状,深入分析了现有工艺在实际开采过程中存在的不足,提出了伪倾斜斜坡短臂采煤法,旨在为中国复杂型急倾斜煤层开采工艺的研究提供借鉴。     

18403综采工作面过平行全长大断面空巷技术的研究

18403工作面过平行全长大断面空巷的研究实践是屯兰矿首例,在西山乃至全国范围内寥寥无几。过空巷时采用加强支护、切顶卸压、调斜工作面的方法,突破了原有技术理念,提高了屯兰矿对切顶卸压先进技术的理解与运用,为以后相似条件下的安全生产提供技术支撑及指导。综采工作面经过空巷时容易造成大面积冒顶,影响安全生产;若不开采空巷区域的煤层又会造成资源浪费和频繁搬家倒面的情况,因此掌握综采工作面过空巷的技术,对于安全生产、缓解接替紧张有极其重大的现实意义,其研究成果能够迅速在相同煤层、类似巷道推广应用,具有广阔的应用前景。     

Novel insights on the impact of top water on Steam‐Assisted Gravity Drainage in a point bar reservoir

As efforts are made to efficiently exploit and recover bitumen resources in Canada, increasingly more complex reservoirs in the Athabasca area continue to challenge the application of Steam‐Assisted Gravity Drainage (SAGD) technology. Several studies have been done to investigate the impact of heterogeneities/complexities such as shale barriers, lean zones, and top and bottom water on the performance of the SAGD process. However, the literature is deficient for point bar deposits with top water zones, a common occurrence in oil sands systems. This study, by using thermal reservoir simulation, examines SAGD performance in a point bar deposit reservoir where an overlying top water and an inclined heterolithic strata (IHS) is present. The results show that where the top water is unconfined and steam injection pressure is higher than that of the top water zone, there is a loss of thermal energy, but the top water does not impact steam chamber development. At steam injection pressure lower than that of the top water zone, top water continuously drains into the reservoir and constrains the size of the chamber. However, the IHS zone helps to delay drainage of the top water into the chamber when steam is injected at underbalanced conditions. Finally, under proper steam injection pressure conditions, top water production can be considerably delayed.     

大通煤业主斜井带式输送机设计变更及工艺优化

本文基于大通煤业矿井兼并重组整合项目初步设计,结合矿井配套选煤厂的建设情况,利用现有的带式输送机,重新优化了主斜井带式输送机设计方案,并对优化方案的难点提出了解决方法,为同类型矿井的改造设计提供了参考。     

Effect of Solute Elements and Cooling Rate on Strain in Brittle Temperature Range of Continuously Cast Strand

A micro-segregation model of solute elements in mushy zone withδ/γtransformation during solidification was established based on the regular hexagon transverse cross section of dendrite shape proposed by finite difference method under the non-equilibrium solidification condition.The model was used to calculate the non-equilibrium pseudo binary Fe-C phase diagram and the strain of steels induced by variation of temperature in brittle temperature range.On the basis of the phase diagram and the strain,the strain curve in brittle temperature range as a function of carbon content for continuously cast strand was introduced and obtained.Solute elements change the position of the strain curve.And cooling rate changes the position and the shape of the strain curve.The comprehensive formula of the strain as functions of solute elements and cooling rate in brittle temperature range has been obtained by nonlinear fitting program.