C105管桩混凝土设计参数取值的探讨

通过试验得出了C105混凝土100 mm×100 mm×100 mm立方体非标准试件抗压强度换算系数以及C105混凝土的标准方差和强度变异系数。采用理论计算,得到了棱柱体抗压强度与立方体抗压强度的比值α_c1,并与试验实测平均值进行了比较,验证了理论计算方法的可行性。此外,通过对比分析,探讨了直接外延法和引用公式法两种C105混凝土设计参数计算方法的正确性,研究结果可为C105管桩混凝土的设计和应用提供参考。     

配分工艺对中碳Ti-Mo高强Q&P钢组织和性能的影响

摘要：采用盐浴实验、扫描电镜、透射电镜、拉伸实验和磨损实验等手段，研究了配分工艺对中碳Ti Mo钢组织和性能的影响，分析了不同配分工艺处理下的组织演变和性能变化。结果表明，显微组织主要由回火马氏体、渗碳体、(Ti，Mo)C粒子组成。随着配分时间的延长和配分温度的升高，板条马氏体数量减少，马氏体板条厚度增加，边界钝化。此外，随着配分温度从310℃提高至400℃，抗拉强度、硬度和低温冲击韧性同时下降，分别降低约250MPa、56HV和15J。最后，Ms以下温度配分（310℃）试样的耐磨损性能明显优于Ms以上温度配分（400℃）试样。Ms以下温度配分试样磨损表面形貌以塑性变形为主，Ms以上温度配分试样磨损表面以犁沟为主。     

“方变圆”变径筒状结构滑模施工技术

为解决塔式光热的核心构筑物吸热塔"方变圆"变径超高筒体结构施工难题,选用一套可变形的滑模平台系统,通过操作系统上可调千斤顶支座、门架横向液压千斤顶装置、多处可调节模板角度和收缩模板的丝杆等,使得滑模根据施工需求可在一定的范围内调节模板倾角、间距,并逐步完成收缩变形,其理论滑模允许偏角20°,最终高效完成异形结构施工。该滑模系统刚度大、承载及堆料能力强、空间大、机械化程度高,施工操作简单,安全性高,适应沙漠极端环境。全过程仅需使用一套滑模体系,就能完成方形段、方变圆的变形段及圆形段施工,大大提高了施工效率,为类似环境下相似结构的施工提供了一定的参考。     

One-step preparation of the superhydrophobic Al alloy surface with enhanced corrosion and wear resistance

Corrosion and wear failures are bottlenecks for restricting applications and developments of Al-based functional materials. As a new lubrication technology, superhydrophobic preparation provides an effective way to settle Al alloy corrosion. The preparation methods of superhydrophobic Al alloys are mainly multistep strategies. In this study, superhydrophobic Al alloy, has been prepared by an efficient one-step electrochemical etching process. Meanwhile, its micromorphology has been observed by a scanning electron microscope. The wettability has been measured by video optical contact angle meter. The corrosion behavior has been tested by electrochemical workstation, and wear performance has been characterized by friction tester. The results show that the micro-nanoterraced concave–convex structure has been fabricated and an as-prepared surface exhibits excellent superhydrophobic behavior. Further electrochemical and tribological tests show that corrosion resistance and wear resistance have also been significantly improved. This study provides a new method to prepare wear-resistant and corrosion-resistant Al alloy for widening applications of multifunctional Al-based engineering materials.     

Prediction models for multiphase-flow-induced corrosion of API X80 steel in CO2/H2S environment

In the offshore oil and gas industry, mainly focusing on the use of rigid or flexible pipes of subsea infrastructure applied to risers or flowlines, one of the greatest difficulties is the interpretation of the combined effects of the various correlated phenomena (hydrodynamic effects of intermittent flow, the effects of corrosivity of the environment in addition to variations in pressure, temperature, and dynamic loading). On the basis of this scenario, defining the degree of severity of each of the correlated system variables becomes of fundamental importance for establishing reliable criteria for selecting materials for subsea application. The established flow pattern directly affects the corrosion rate (or the pipe material mass loss), but the balance of other variables including possible changes in the physical and transported fluid chemical properties may increase the damage up to an order of magnitude, which is a piece of information normally not foreseen in design criteria. Therefore, to improve the understanding of the corrosion study influenced by multiphase flow, a testing loop was designed and assembled at the Corrosion and Protection Laboratory of the Institute for Technological Research, in which API X80 steel coupons were positioned in locations with a 0° and 45° inclinations. Tests were conducted by varying the partial pressure of the gaseous phase containing blends of CO₂ and H₂S with N₂ balance, mixed with the liquid phase containing light oil and heavy oil in water with salinity (NaCl)-simulating oil well conditions with 80% water cut. The main objective of this study is to establish models that can predict the corrosion intensity in conditions close to those obtained experimentally. To achieve results, the multiple regression and Box–Cox transformation methods were applied. These models will make possible damage prediction and optimization of matrix parameters for the multiphase-loop test.     

磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Corrosive wear behavior of HVOF-sprayed micro-nano-structured Cr3C2–NiCr cermet coatings under aqueous media

A novel micro-nano-structured Cr₃C₂–NiCr cermet coating was prepared on 316L stainless steel by high-velocity oxygen fuel spraying technology (HVOF). Cermet coatings with different contents of micro-and nano-sized Cr₃C₂ particles as the hard phase and a NiCr alloy matrix as the bonding phase were prepared and characterized in terms of porosity, microhardness, and corrosive wear resistance in a 3.5% NaCl solution and artificial seawater. Compared to nanostructured coatings, micro-nano-structured coatings avoid decarburization and reduce nanoparticle agglomeration during the spray process, and mechanical and electrochemical properties were improved in comparison with those of conventional coatings. The micro-nano-structured Cr₃C₂–NiCr coating rendered low porosity (≤0.34%) and high microhardness (≥1105.0HV_0.3). The coating comprising 50% nano-sized Cr₃C₂ grains exhibited the best corrosive wear resistance owing to its densest microstructure and highest microhardness. Furthermore, compared to static corrosion, the dynamic corrosion of the coatings led to more severe mechanical wear, because corrosion destroyed the coating surface and ions promoted corrosion to invade coatings through the pores during corrosion wear.     

Microstructure-abrasive wear correlation of in situ ZA27/TiC composites

Abrasive wear is a complex surface degradation process driven by various factors such as microstructure, the mechanical properties of the target material, the abrasive, loading conditions, and the surrounding environment. In this study, in situ TiC reinforced Zinc Aluminum alloy composites were prepared through a liquid metallurgy route and the synergistic effect of applied load, sliding speed, abrasive grit size and TiC content on the high-stress abrasive wear response were investigated. The test materials' wear response was established by characterising wear surfaces, sub-surfaces, debris particles, and an abrasive medium. The study suggests that the wear resistance of the specimens decreases with an increase in the applied load, and the composite reinforced with 10 wt % of TiC shows superior wear behaviour among all the test materials. The study also points out that the ZA-27 alloy reinforced with in situ TiC can be a suitable replacement of the conventionally used materials for automotive applications.     

Tribological behavior studies of chemically bonded phosphate ceramic coatings reinforced with modified multi-walled carbon nanotubes (MWCNTs)

To improve the wear resistance of the chemically bonded phosphate ceramic coatings, MWCNTs are selected as the reinforcement after the modification. The high temperature wear experiment is carried out to investigate the wear behavior of the coatings with different temperatures. The results suggest that, when the temperature is below 500℃, MWCNTs can decrease friction coefficient, and the lowest friction coefficient is about 0.28, but MWCNTs lose the lubricant function at 500℃ and the friction coefficient keeps at the level of ~ 0.68. In addition, the wear resistance of coatings is improved with the introduction of MWCNTs at 100℃ and 300℃ (the wear rate is below 15X10^-3mm³/Nm), but keeps similar level at 500℃ (the wear rate is ~ 22 × 10⁻³mm³/Nm). Besides, the wear mechanism of the coatings reinforced by MWCNTs is also investigated based on the wear behavior and microstructural characterizations. MWCNTs improve the fracture toughness by preventing the crack generation and forming the bridge when crack occurs, which leads to smooth wear tracks and good wear resistance of coatings. The coatings with MWCNTs achieve poor wear resistance at 500℃ because MWCNTs lose their strength and resistance to fatigue by oxidizing.     

Tribological behavior of composites fabricated by reactive SPS sintering in Ti-Si-C system

In this study, wear and friction behavior of two based-composites from the Ti-Si-C system, (40 wt% TiC; 28 wt% Ti₅Si₃; 17 wt% Ti₃SiC₂) and (18 wt% TiC; 26 wt% Ti₅Si₃; 41 wt% Ti₃SiC₂) reinforced by 15 wt% of large size SiC (100-150 µm) particles were investigated. The four-phase composites exhibited approximatively the same friction coefficient (µ ~ 0.9) under high loads (10 N and 7 N). The composite with high Ti₃SiC₂ showed higher wear rate values by one order of magnitude. However, under 1 N, the composite with high TiC content showed a higher running-in period and a lower steady state µ value (0.37 after 1000 m sliding distance). Scanning electron microscopy, Energy Dispersive X-Ray and Raman spectroscopy analysis of the worn surfaces of the two composites revealed that oxidation was the dominant wear mechanism. The oxidation process and the removal kinetics of the oxides during sliding controlled the tribological behavior of the composites. The influence of processing variables on microstructures development and wear mechanisms of the composites is discussed.