Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

The influence of preparation conditions on the electrochemical behaviour of CuO in a Li/CuO cell

A dozen CuO samples prepared under various conditions and from different starting materials were evaluated as cathode materials for a primary Li/CuO cell. The “thin electrode” method was used for rapid evaluation of the samples. Both coulombic efficiency and discharge voltage depend considerably on the method of synthesis. No correlation was found between the specific surface area and the resistivity of the samples on the one hand and the cathode performance on the other. Best results were obtained from CuO prepared by the oxidation of Cu₂O under controlled temperature and time of oxidation.     

A review of the metallurgy of heat treatment of welded joints

This paper deals with the metallurgical changes which occur during heat treatment of welded joints. Stress relieving heat treatment in the temperature range below A₁, the normalizing heat treatment and the heat treatment in the intercritical range A₁–A₃, are all considered. The thermal regime of welding is described. The practice of intercover of the weldment before applying PWHT to ambient temperature is described. It is stressed that the aim of stress-relieving heat treatment is not only to relax internal stresses but also to improve the microstructure and impact properties of HAZ and weld metal, to improve dimensional stability and increase resistance against stress corrosion. Examples are given of the effect of annealing in the intercritical range A₁–A₃ on the improvement in toughness of electroslag welded joints. Changes in dislocation distribution and density, precipitation processes and grain sizes during PWHT are described.     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.     

爽“朗”曲调 芬朗SP-6.5A两分频套装测试报告

正自2月在第十届AAITF展会上公布了今年陆续发售的众多全新产品后,笔者一直关注着芬朗公司的具体动向。本月中旬,笔者受邀前往广州车元素旗舰店测试芬朗Feelart推出不久的性价比型两分频套装喇叭——SP-6.5A。外观工艺简单介绍一下SP-6.5A的外观,其实从产品系列来讲,SP-6.5在芬朗的产品线中属于第三梯队的极速摇滚系列,该系列的产品定位是为满足车主在进入汽车音响改装之门后对音色声效     

Effect of temperature on the separation of some Δ9-cis-trans isomers of methyl esters of fatty acids by open tubular gas chromatography

The influence of temperature on the gas chromatographic separation ofcis-trans isomers of the methyl esters of some monounsaturated fatty acids was studied on capillary columns coated with Apiezon L, BDS and DEGS. As far as methyl oleate and methyl elaidate are concerned, the separation is better at lower temperatures on Apiezon L (180–210 C) and at higher temperatures on polyester phases (BDS, DEGS; 150–180 C). The influence of temperature on the separation ofcis-trans isomers on the three stationary phases under study is explained by the higher values of δECL/δt forcis isomers. The variation of the equivalent carbon chain length with temperature can be used for the identification ofcis-trans isomers in natural mixtures.     

The joint movement of pebbles in solving the ($$N^2-1$$)-puzzle suboptimally and its applications in rule-based cooperative path-finding

The present paper deals with the problem of solving the (\(n^2 - 1\))-puzzle and cooperative path-finding (CPF) problems sub-optimally by rule-based algorithms. To solve the puzzle, we need to rearrange \(n^2 - 1\) pebbles in the \(n \times n\)-sized square grid using one vacant position to achieve the goal configuration. An improvement to the existing polynomial-time algorithm is proposed and experimentally analyzed. The improved algorithm represents an attempt to move pebbles in a more efficient way compared to the original algorithm by grouping them into so-called snakes and moving them together as part of a snake formation. An experimental evaluation has shown that the snakeenhanced algorithm produces solutions which are 8–9 % shorter than the solutions generated by the original algorithm. Snake-like movement has also been integrated into the rule-based algorithms used in solving CPF problems sub-optimally, which is a closely related task. The task in CPF consists in moving a group of abstract robots on an undirected graph to specific vertices. The robots can move to unoccupied neighboring vertices; no more than one robot can be placed in each vertex. The (\(n^2 - 1\))-puzzle is a special case of CPF where the underlying graph is a 4-connected grid and only one vertex is vacant. Two major rule-based algorithms for solving CPF problems were included in our study—BIBOX and PUSH-and-SWAP (PUSH-and-ROTATE). The use of snakes in the BIBOX algorithm led to consistent efficiency gains of around 30 % for the (\(n^2 - 1\))-puzzle and up to 50 % in for CPF problems on biconnected graphs with various ear decompositions and multiple vacant vertices. For the PUSH-and-SWAP algorithm, the efficiency gain achieved from the use of snakes was around 5–8 %. However, the efficiency gain was unstable and hardly predictable for PUSH-and-SWAP.     

Hybrid charge control for stick-slip piezoelectric actuators

The article describes an analog electronic circuit for driving stick-slip piezoelectric linear actuators. The task for the amplifier is to provide a high-voltage asymmetric sawtooth-like signal and feed it into a capacitive load. Generation of excessive heat must be avoided while maximizing the slew rate. In order to guarantee a steady translation, the hysteretic behaviour of the piezoelectric material must be compensated. Combination of a charge control scheme with switching is proposed as an efficient solution. Laboratory experiments confirm the superiority of this tailored solution over other existing techniques based on versatile linear voltage amplifiers.     

Influence of different SiC surface treatments performed prior to Ni ohmic contacts formation

This work is dealing with the influence of surface treatment on ohmic contacts to hexagonal N-type SiC with medium doping level. The contact materials were Ni and Ni₂Si. The structures had to be annealed at high temperatures in order to reach ohmic behavior. A number of surface treatment methods were tested: wet cleaning, plasma etching, intentional oxidation with etching, H₂ annealing and their combinations. After some types of cleaning, the SiC surface was immediately analysed using the XPS method. The results of the analyses showed that the composition of the surface was not much influenced by these treatments. At lower annealing temperatures (approx. up to 850 °C) the prepared contacts showed Schottky behavior with large scatter of parameters. After annealing at approx. 960 °C, where the onset of ohmic behavior is expected, the structures were truly ohmic and of good parameters. Cleaning methods had just a negligible influence on the electrical parameters of the ohmic contacts. An explanation for these observed facts is suggested: Although - already on the basis of the XPS results - we could speak about a negligible influence of the cleaning onto the contact parameters, there might come across also other mechanisms coming from interaction of contact materials with SiC, which caused similar behavior of ohmic contacts on differently treated surfaces.