Analysis of adhesively bonded CFRE composite scarf joints modified with MWCNTs

The main objective of the present work is to improve the performance of bonded joints in carbon fiber composite structures through introducing Multi-Walled Carbon Nanotubes (MWCNTs) into Epocast 50-A1/946 epoxy, which was primarily developed for joining and repairing of composite aircraft structures. Results from tension characterizations of structural adhesive joints (SAJs) with different scarf angles (5–45°) showed improvement up to 40% compared to neat epoxy (NE)–SAJs. Special attention was considered to investigate the performance of SAJs with 5° scarf angle under different environments. The tensile strength and stiffness of both NE-SAJs and MWCNT/E-SAJs were dramatically decreased at elevated temperature. Water absorption showed a marginal drop of about 2.0% in the tensile strength of the moist SAJs compared to the dry one. Cracks initiation and propagation were detected effectively using instrumented-SAJs with eight strain gauges. The experimental results agree well with the predicted using three-dimensional finite element analysis model.     

Stochastic free vibration analyses of composite shallow doubly curved shells – A Kriging model approach

This paper presents the Kriging model approach for stochastic free vibration analysis of composite shallow doubly curved shells. The finite element formulation is carried out considering rotary inertia and transverse shear deformation based on Mindlin’s theory. The stochastic natural frequencies are expressed in terms of Kriging surrogate models. The influence of random variation of different input parameters on the output natural frequencies is addressed. The sampling size and computational cost is reduced by employing the present method compared to direct Monte Carlo simulation. The convergence studies and error analysis are carried out to ensure the accuracy of present approach. The stochastic mode shapes and frequency response function are also depicted for a typical laminate configuration. Statistical analysis is presented to illustrate the results using Kriging model and its performance.     

亲子乐园空调送风方式的数值模拟研究

大型综合室内亲子乐园属于高大空间,设有游乐设施和游戏的特殊性使得对空间的舒适性要求一致,但是送风气流遇阻严重,室内存在较多气流死角,影响室内空气质量和儿童健康。因此其空调设计不仅需要考虑温度、风速的空间均匀度,还要考虑各点的空气龄和PMV-PPD指标。以天津某亲子乐园为研究对象,利用scSTREAM软件对适用于该房间的辐射供冷加新风、置换通风、混合通风三种空调方式的送风效果进行数值模拟分析,从流场的均匀性、人员的热舒适性等方面对模拟结果进行探讨,研究结果表明辐射供冷加新风方式的空间均匀性和PMV指标最佳,混合通风方式的空气龄最小。     

Damage identification in concrete using impact non-linear reverberation spectroscopy

High amplitude non-linear acoustic methods have shown potential for the identification of micro damage in brittle materials such as concrete. Commonly, these methods evaluate a non-linearity parameter from the relative change in frequency and attenuation with strain amplitude. Here, a novel attenuation model is introduced to describe the free reverberation from a standard impact resonance frequency test, together with an algorithm for estimating the unknown model coefficients. The non-linear variation can hereby by analyzed over a wider dynamic range as compared to conventional methods. The experimental measurement is simple and fully compatible with the standardized free-free linear impact frequency test.     

THE effect of Srandom DOPANT fluctuation on threshold voltage and drain current variation in junctionless nanotransistors

We investigate the effect of dopant random fluctuation on threshold voltage and drain current variation in a two-gate nanoscale transistor. We used a quantum-corrected technology computer aided design simulation to run the simulation (10000 randomizations). With this simulation, we could study the effects of varying the dimensions (length and width), and thicknesses of oxide and dopant factors of a transistor on the threshold voltage and drain current in subthreshold region (off) and overthreshold (on). It was found that in the subthreshold region the variability of the drain current and threshold voltage is relatively fixed while in the overthreshold region the variability of the threshold voltage and drain current decreases remarkably, despite the slight reduction of gate voltage diffusion (compared with that of the subthreshold). These results have been interpreted by using previously reported models for threshold current variability, load displacement, and simple analytical calculations. Scaling analysis shows that the variability of the characteristics of this semiconductor increases as the effects of the short channel increases. Therefore, with a slight increase of length and a reduction of width, oxide thickness, and dopant factor, we could correct the effect of the short channel.     

综放高瓦斯矿井煤层瓦斯涌出量综合预测

为了成功预测竹林山煤矿综放高瓦斯矿井大采高工作面煤层瓦斯涌出量,以主采3号煤层为主要研究对象,针对3号煤层以往开采情况,通过布设测点测量其煤层瓦斯含量和了解相邻矿井瓦斯含量,采用分源预测法、回归法及统计法等预测方法得到了3号煤层瓦斯含量的分布规律,并绘制了3号煤层的瓦斯含量等值线图。对矿井不同生产时期的瓦斯含量进行预测,得到了生产前期、中期及后期采区的最大绝对瓦斯涌出量和最大相对瓦斯涌出量,说明了竹林山煤矿各个时期均属于高瓦斯矿井。     

Design criterion for fatigue strengthening of riveted beams in a 120-year-old railway metallic bridge using pre-stressed CFRP plates

This study presents a design criterion developed for fatigue strengthening of a 120-year-old metallic railway bridge in Switzerland and presents a pre-stressed un-bonded reinforcement (PUR) system developed to apply the strengthening. The PUR system uses carbon fiber reinforced polymer (CFRP) plates; however, unlike conventional pre-stressed CFRP reinforcement methods, preparation of the existing metallic bridge surface is not required. This decreases the time required for on-site strengthening procedures. The principle of the constant life diagram (CLD) and two fatigue failure criteria (Johnson and Goodman) are described. Analytical formulations are developed based on the CLD method to determine the minimum CFRP pre-stress level required to prevent fatigue crack initiation. The PUR system uses an applied pre-stress force to reduce the mean stress level (and stress ratio) to shift an existing fatigue-susceptible metallic detail from the ‘at risk’ finite life regime to the ‘safe’ infinite life regime. The applied CLD method is particularly valuable when the stress history of the detail is not known and it is difficult to assess the remaining fatigue life. Moreover, it is shown that the currently adopted approach in many structural codes which emphasizes stress range as the dominant parameter influencing fatigue life are non-conservative for tension–tension stress patterns (i.e., stress ratios of 0 < R < 1). Analyses show that the modified Johnson formula accurately reflects the combined effect of stress range, mean stress level, and material properties, and offers a relatively easy design procedure. Details of a retrofit field application on members of a riveted wrought iron railway bridge are given. A wireless sensor network (WSN) system is used for long-term monitoring of the on-site CFRP stress levels and temperature of the retrofitted details. WSN measurements indicate that increases in ambient temperature result in increased CFRP pre-stress levels.     

Nonlinear response in glass fibre non-crimp fabric reinforced vinylester composites

This paper addresses the nonlinear stress-strain response in glass fibre non-crimp fabric reinforced vinylester composite laminates subjected to in-plane tensile loading. The nonlinearity is shown to be a combination of brittle and plastic failure. It is argued that the shift from plastic to brittle behaviour in the vinylester is caused by the state of stress triaxiality caused by the interaction between fibre and vinylester. A model combining damage and plasticity is calibrated and evaluated using data from extensive experimental testing. The onset of damage is predicted using the Puck failure criterion, and the evolution of damage is calibrated from the observed softening in plies loaded in transverse tension. Shear loading beyond linear elastic response is observed to result in irreversible strains. A yield criterion is implemented for shear deformation. A strain hardening law is fitted to the stress-strain response observed in shear loaded plies. Experimental results from a selection of laminates with different layups are used to verify the numerical models. A complete set of model parameters for predicting elastic behaviour, strength and post failure softening is presented for glass fibre non-crimped fabric reinforced vinylester. The predicted behaviour from using these model parameters are shown to be in good agreement with experimental results.