Influence of high energy ball milling on structural,microstructural and optical properties of TiO2 nanoparticles

The influence of high-energy ball milling on structural, microstructural, and optical properties of TiO₂ by modifying the nanoparticle size was studied. Five samples were extracted at different milling times (0, 2, 4, 8, and 13 h). The average particle sizes estimated by dynamic light scattering (DLS) were 205, 155.8, 116.8, 82.9, and 82.7 nm at 0, 2, 4, 8, and 13 h, respectively. X-ray diffraction analysis confirmed progressive broadening of the peaks as the milling time elapsed. Besides, a correlation was found between d spacing and the average crystal size. The UV–Vis diffuse reflectance spectra of TiO₂ revealed a decrease in reflectance due to particle size reduction. Similarly, an alteration of the bandgap transition energy was presented, whose values gradually decreased from 2.966 eV to 2.861 eV for the sample without and with the maximum duration milling performed (13 h), respectively. Likewise, the SEM analysis showed a distribution in nanoparticle size that became more homogeneous and smaller average grain size as the milling duration was longer.     

行李箱外板浮动整形模设计

介绍了某轿车行李箱外板的翻边侧整形模设计过程,行李箱外板的侧法兰翻边上存在凹包,其翻边方向和凹包成形方向不同,常规需要2道工序分别完成翻边和凹包成形。该模具突破了传统的设计结构,在翻边机构中设置了凹包成形机构,将2个不同方向的成形复合到1道工序中,减少了模具数量,降低了冲压成本和工装成本。     

导管架平台上部组块双船拆除

为研究复杂海域环境中海洋平台双船拆除方法的安全性与可操作性,采用水动力数值计算与水池模型试验相结合的方法进行研究。将双船水动力耦合计算与水池模型试验进行对比,在相对理想海况下,结合与实际工况接近的规则波作用,进行驳船水动力性能变化与运动响应的幅值分析。在受力分析方面,对甲板耦合装置进行改良设计,对比试验数据与数值计算数据,得到受力在合理范围内的结论。研究内容为实际施工的合理性提出一定的指导性意见。     

Physical and electrochemical behavior of affordable Na3SbS4 solid electrolyte at different heat treatment temperatures

High-capacity and affordable all-solid-state Na-ion batteries have gathered increasing interest in recent years owing to low-cost sodium, which contributes to reducing the price of these Na-ion batteries to approximately 70% of that in lithium batteries. However, in terms of electrolyte performance and battery cost, the complete replacement of lithium batteries has a long way to go. In this work, low-cost and high-safety Na₂S·9H₂O materials are used in synthesizing Na₃SbS₄ solid electrolyte, the price of which is only one-fifth that of high-purity Na₂S. The structure and electrochemical properties are studied through X-ray diffraction analysis, Raman spectroscopy, scanning electron microscopy, and electrochemical tests. Results indicate that a multiphase Na₃SbS₄ structure containing cubic and tetragonal phases formed after heat treatment at 300 °C. In addition, a third phase transition of Na₃SbS₄ is inferred after further heating at 600 °C. This phase structure contributes to the improvement of electrochemical performance by promoting increasing ionic conductivity to 0.54 mS cm^?1 at room temperature (25 °C) and reducing activation energy to 0.076 eV. This work provides an affordable material with good electrochemical properties and not only simplifies the preparation but also greatly reduces the risk of the process.     

溢流型球磨机进料口密封装置的改进

分析了溢流型球磨机进料口矿浆泄漏的原因以及泄漏后给球磨机润滑系统和环境所带来的危害。通过对溢流型球磨机进料口密封装置的改进,减少和杜绝了矿浆泄漏,改善了球磨机运行环境,延长了润滑油使用周期、提高了球磨机有效作业率,降低了球磨机运行成本。     

Preparation of YSZ porous ceramics with precise porosity control

Conventional preparation of porous ceramics often hard to accurately control the porosity of the samples. In this paper, by improving the foaming method, the foaming process is placed in the limited space of the ball mill tank, and YSZ porous ceramics with different porosity are obtained by changing the amount of slurry. Initial results showed that the porosity of the sample varies linearly with the increasing of addition of slurry. From the microscopic morphology, it can be seen that the increase in slurry content will reduce the number of pore with little changed size, which lead to the decrease in porosity. Therefore, with simple calculation YSZ porous ceramics with 85%, 80%, 75%, 70%, and 65% porosity can be obtained using the method of foaming in limited space by ball milling.     

自旋对角接触球轴承弹流润滑与油膜刚度的影响

根据角接触球轴承自旋运动特征，同时考虑弹流润滑效应，建立角接触球轴承考虑自旋运动的弹流润滑模型；采用多重网格法求解弹性变形，利用有限差分法迭代求解雷诺方程，得到较为精确的数值解；分析不同赫兹接触压力、滚道表面粗糙度下自旋对角接触球轴承弹流润滑和油膜刚度的影响。结果表明：考虑自旋时随着Hertz接触压力、自旋角速度增大，油膜厚度减小，油膜压力增大，油膜承压区域呈细长状，并向接触中心靠近；随着滚道表面粗糙度幅值增大，油膜压力和膜厚均出现了波动，且考虑自旋运动时，轴承油膜厚度明显减小，油膜局部压力峰值更大；随着卷吸速度、润滑油黏度增大，油膜刚度减小，而考虑自旋运动时油膜刚度值更大；随着自旋角速度增大，油膜刚度逐渐增大。     

隔水管伸缩装置技术发展

隔水管伸缩装置是隔水管系统中设计、制造难度最高,结构最为复杂的单元设备。目前国内鲜有技术人员对隔水管伸缩装置进行研究、设计和制造。剖析了伸缩装置的工作原理,指出了伸缩装置的关键功能模块,在调研了国外多家企业的伸缩装置产品后,提出了伸缩装置设计制造中的关键技术,并在此基础上提出了隔水管伸缩装置未来的发展方向,可为隔水管伸缩装置产品的设计提供参考。     

SiFe@C负极复合材料的结构及性能

以SiFe合金和沥青为原料，采用机械球磨和高温热解法制备了SiFe@C负极复合材料，并对SiFe及一系列不同热解温度下制备的SiFe@C复合材料进行对比研究。利用XRD、SEM、TEM、EDS和恒流充放电测试仪对SiFe@C复合材料的物相、颗粒形貌及电化学性能进行表征。结果表明，在850℃热解温度下制得的SiFe@C负极复合材料首次放电比容量达到1 376.25 mAh/g，首次库仑效率为86.35%，经过70次循环后放电比容量为940.33 mAh/g，库仑效率达到98.78%，容量保持率为76.32%，循环性能远高于SiFe和其他热解温度下的SiFe@C复合材料，而且具有良好的倍率性能。