基于关键路径延时检测的自适应电压缩减技术

为了减小传统的最差情况设计方法引入的电压裕量,提出了一种变化可知的自适应电压缩减(AVS)技术,通过调整电源电压来降低电路功耗.自适应电压缩减技术基于检测关键路径的延时变化,基于此设计了一款预错误原位延时检测电路,可以检测关键路径延时并输出预错误信号,进而控制单元可根据反馈回的预错误信号的个数调整系统电压.本芯片采用SMIC180 nm工艺设计验证,仿真分析表明,采用自适应电压缩减技术后,4个目标验证电路分别节省功耗12.4％,11.3％,10.4％和11.6％.     

Modelling,simulation and identification of an engine air path electromechanical actuator

This paper deals with the modelling and the identification of an electromechanical Diesel engine actuator. The studied Bosch GPA-S actuator is designed for swirl/tumble flaps to control the air amount entering into the cylinder. This study aims to design a complete simulator that reproduces, with sufficient accuracy, the actuator dynamics taking into account the effects of the friction phenomenon. Hence, an overview of the actuator structure and its operation principle is first given. Then, its mathematical model as well as the nonlinearity, related to its behaviour, is discussed. Next, three identification procedures, which allow estimating both the system parameters and the friction model coefficients, are introduced. Finally, simulation results, using MATLAB, and experimental results, using LabVIEW, are presented demonstrating the effectiveness of the proposed techniques.     

Voltage reference architectures for low-supply-voltage low-power applications

This paper presents a voltage reference generator architecture and two different realizations of it that have been fabricated within a standard 0.18 μm CMOS technology. The architecture takes the advantage of utilizing a sampled-data amplifier (SDA) to optimize the power consumption. The circuits achieve output voltages on the order of 190 mV with temperature coefficients of 43 ppm/°C and 52.5 ppm/°C over the temperature range of 0 to 120°C without any trimming with a 0.8 V single supply. The power consumptions of the circuits are less then 500 nW while occupying an area of 0.2 mm² and 0.08 mm², respectively.     

测井资料在优选压裂层位中的应用

压裂是低孔、低渗油层改造的主要增产措施。根据常规测井资料、岩石物理实验分析数据及试油成果。研究储层四性关系，确定区块的低孔、低渗储层评价标准。进一步对油层进行分类，有针对性地为油层压裂提供施工层位和准确的储层参数。通过商543区块实例，阐述了选择压裂层位的方法。     

湘中海相浅层湘冷1井酸压工艺研究及应用

湘冷1井具有气层埋藏浅（400m-500m）、纵向上裂隙发育的特点，属低孔、低渗的含泥质灰岩致密储层。大量室内实验和研究采用“前置液酸压＋闭合酸化”工艺技术，并优选了相应降阻酸和闭合酸配方。通过酸压实现了该井工业油气流的突破，取得了明显的增产效果，为新区海相浅层气的开发探索出了一套成熟的改造增产措施。     

P(DBF-VA)型柴油低温流动性改进剂的研制

针对新疆地产柴油蜡含量较高的特点,以游离基聚合法合成了富马酸双链混合酯和醋酸乙烯酯共聚物型[P(DBF-VA)]柴油低温流动改进剂,利用正交实验研究了单体配比,引发剂用量,溶剂用量,聚合温度对聚合物降冷滤效果的影响。共聚物用IR进行表征,利用XRD初步探讨了该降凝剂的降凝机理。结果表明:该剂能使吐哈—10~#、0~#柴油冷滤点降低10℃和7℃;使独山子0~#柴油冷滤点下降12℃;使石化0~#柴油冷滤点下降8℃;使克拉玛依0~#柴油的冷滤点下降8℃。     

HART通信协议在汽油机速度测量和监控方面的应用

首先介绍了HART通信协议及他的优点，然后介绍了HART通信协议在汽油机测速方面的软件实现。该软件主要采用目前流行的VB编程语言。可设计出界面友好、功能强大的测量和监控软件。     

微流控分析芯片制作中的低温键合技术

微流控分析芯片制作方法的研究是微流控分析的基础。制作性能良好的微流控分析芯片时,基片与盖片的键合技术十分重要。本文针对近年来发展迅速的低温键合技术,对各种方法进行了评价,并对其发展前景进行了展望。