超宽带大功率合成器设计北大核心CSCD

在80 MHz~1 GHz频段,单个功率管输出功率能达到100 W以上,为研制输出功率400 W的功率放大器,文中设计了四路功率合成器。该合成器需要实现功率容量大、工作频带宽、体积小的设计目标。在功率容量方面,文中采用悬置带状线结构,其功率容量远远大于微带线结构;在工作频带方面,采用切比雪夫九节阻抗变换器,将工作带宽拓宽为80 MHz~1 GHz;在体积方面,文中合成器的功率合成部分采用Y型节级联实现四路功率合成,阻抗变换部分采用切比雪夫阻抗变换器进行阻抗变换,该结构相较于磁环巴伦功率合成器,不但具有损耗小、平坦度高的优点,而且通过将阻抗变换器设计成曲折的形状,进一步缩小了合成器体积。仿真与实测结果显示该合成器在80 MHz~1 GHz范围内还具有较高的平坦度,合成效率可达90%以上。     

An active balancer with rapid bidirectional charge shuttling and adaptive equalization current control for lithium-ion battery strings

This article proposes an active balancer, which features bidirectional charge shuttling and adaptive equalization current control, to fast counterbalance the state of charge (SOC) of cells in a lithium-ion battery (LIB) string. The power circuit consists of certain bidirectional buck-boost converters to transfer energy among the different cells back and forth. Owing to the characterization of the open-circuit voltage (OCV) vs SOC in LIB being relatively smooth near the SOC middle range, the SOC-inspected balance strategy can achieve more precise and efficient equilibrium than the voltage-based control. Accordingly, a compensated OCV-based SOC estimation is put forward to take into account the discrepancy of SOC estimation. Besides, the varied-duty-cycle (VDC) and curve-fitting modulation (CFM) methods are devised herein to tackle the problems of slow equalization rate and low balance efficacy, which arise from the diminution in balancing current as the SOC difference between the cells decreases in the later duration of equalization especially. The proposed strategies have taken the battery nonlinear characteristic and circuit parameter nonideality into account and can adaptively modulate the duty cycle with the SOC difference to keep balancing current constant throughout the balancing cycle. Simulated and experimental results are given to demonstrate the feasibility and effectiveness of the same prototype constructed. Compared with the fixed duty cycle and the VDC methods, the proposed CFM has the best balancing efficiency of 81.4%, and the balance time is shortened by 27.1% and 18.6%, respectively.     

用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

Single-switch boost-buck DC-DC converter for industrial fuel cell and photovoltaics applications

The realization of dc-dc converters performs a vital function in exploiting renewable energy sources such as solar photovoltaic (PV) and fuel cell applications. This paper demonstrates a single-switch unidirectional buck-boost dc-dc converter for continuous power flow control, excluding the hybrid switched-capacitor. The proposed converter utilizes a limited number of passive components, only four diodes and three inductors required, in addition to six capacitors. The converter can operate at a wide input voltage range with continues input current. The converter has experimented under real-time conditions with 660 W PV system. The obtained efficiency ranges from 93% to 98%. Furthermore, the converter has interfaced with 550 W fuel cell operated under different fuel pressure. The realized efficiency ranges from 91% to 97%. The maximum measured inductance current ripple is limited to under 0.70 A in both scenarios, whereas 0.16 V is the maximum output voltage ripple.     

基于平均功率平衡控制的磁悬浮分子泵电力失效补偿方法

高速磁悬浮涡轮分子泵（Turbo Molecular Pump, TMP）因其高能量密度、微振动、无需润滑等优点被广泛应用于工业领域，但外部电源失效时，高速转子跌落后与保护轴承产生剧烈撞击和摩擦，将给系统带来致命损害。针对以上问题，提出一种基于平均功率平衡法的电力失效补偿控制（Power Failure Compensation Control, PFCC）方法。首先，设计电机能量回馈电路；其次，对Buck-Boost变换器进行数学建模，设计一种双环非线性控制器，其中电流内环使用滑模控制，电压外环使用平均功率平衡控制（Average Power Balance Control, APBC），并利用Lyapunov函数推导出系统的稳定性条件；最后，通过搭建磁悬浮分子泵PFCC实验平台，对所提出的方法进行实验验证。结果表明：本文所提出的方法具有快速响应和输出鲁棒性，磁悬浮转子由额定转速21000 r/min降至3900 r/min时跌落，电机能量转化效率为96.6%，提高了磁轴承系统的安全性。     

Reduced‐order method for mathematical modeling of multiphase dc‐dc converter

A multiphase dc‐dc converter is effective for miniaturization and achieving high‐power density in a switching power supply. However, its mathematical modeling becomes complex as the phase number of the circuit increases. This study proposes a new modeling method to derive a reduced‐order method in a simple manner. The frequency characteristics of the reduced‐order model are fit to those of the original mathematical model of the multiphase dc‐dc converter. Therefore, the efficacy of the proposed method is validated.     

基于模糊谱聚类的不确定蛋白质相互作用网络功能模块挖掘

针对谱聚类融合模糊C-means（FCM）聚类的蛋白质相互作用（PPI）网络功能模块挖掘方法准确率不高、执行效率较低和易受假阳性影响的问题，提出一种基于模糊谱聚类的不确定PPI网络功能模块挖掘（FSC-FM）方法。首先，构建一个不确定PPI网络模型，使用边聚集系数给每一条蛋白质交互作用赋予一个存在概率测度，克服假阳性对实验结果的影响；第二，利用基于边聚集系数流行距离（FEC）策略改进谱聚类中的相似度计算，解决谱聚类算法对尺度参数敏感的问题，进而利用谱聚类算法对不确定PPI网络数据进行预处理，降低数据的维数，提高聚类的准确率；第三，设计基于密度的概率中心选取策略（DPCS）解决模糊C-means算法对初始聚类中心和聚类数目敏感的问题，并对预处理后的PPI数据进行FCM聚类，提高聚类的执行效率以及灵敏度；最后，采用改进的边期望稠密度（EED）对挖掘出的蛋白质功能模块进行过滤。在酵母菌DIP数据集上运行各个算法可知，FSC-FM与基于不确定图模型的检测蛋白质复合物（DCU）算法相比，F-measure值提高了27.92%，执行效率提高了27.92%；与在动态蛋白质相互作用网络中识别复合物的方法（CDUN）、演化算法（EA）、医学基因或蛋白质预测算法（MGPPA）相比也有更高的F-measure值和执行效率。实验结果表明，在不确定PPI网络中，FSC-FM适合用于功能模块的挖掘。     

基于双面组件的可调支架光伏发电系统仿真研究

以双面光伏组件和可调支架系统为基础,以青海格尔木为模拟地点,利用PVsyst光伏仿真软件,分析了不同调节次数的可调支架系统与固定支架系统在组件正面和背面辐射量、系统发电量、系统收益的差异。研究结果表明：通过调节支架改变光伏组件的角度后,组件最低点离地高度也在变化,直接影响组件正面和背面的辐射接收;光伏方阵前后间距影响土地利用率（GCR）,土地利用率降低后,背面的辐射量和系统发电量都有一定的增加;相对于固定支架双面发电系统,可调支架双面系统在不同调节次数下的组件背面全年辐射量均有一定降低,但整体的发电量得益于正面辐射的增益,最高可达4.8%左右;技术和经济比较结果显示,双面组件采用可调支架系统,每年2次的调节方式,25年生命周期内系统收益最高。文章还分析了单面发电组件和双面组件系统使用可调支架的经济性对比,在相同的调节次数下,双面组件系统的增益明显高于单面组件系统。本文的研究成果对可调支架双面组件发电系统的设计具指导作用。     

Novel CPG algorithm for tracking fast sudden changes based on tangent rule

ABSTRACT

This paper proposes a novel tracking method to deal with fast changes of solar irradiation and power limit change in order to increase tracking efficiency. This goal is achieved by estimating (i) next operating mode and (ii) next step point with the use of tangent rule in triangle. After every fast response to sudden changes, accurate response phase starts in order to track desired power in each operating mode by adaptive step size. Drift problem in defining next operating mode is eliminated in proposed method by estimating next operating mode, and settling time is decreased to about 25 percent of settling time of other methods by estimating next step point. Simulation and experimental results show the performance of proposed method.     

计及RSC控制的DFIG短路电流直流分量解析表达

现有文献针对计及转子变流器(RSC)控制的双馈感应风电机组(DFIG)定子短路电流解析表达,将定子磁链当作一阶直流衰减分量或忽略功率外环控制。基于DFIG电压、磁链和RSC控制方程,得到定子电流关于定子电压和定子功率的传递函数,提出定子电流的精确解析表达式。基于RSC内、外环PI参数关系,推导直流分量衰减时间常数和角频率关于PI参数的表达式。分析了RSC内外环PI参数对定子电流直流衰减分量的影响。仿真结果验证了解析表达式的准确性,为PI参数选取和保护装置测量、整定提供依据。