高耸桥墩保护性爆破拆除关键技术

为解决高耸钢砼桥墩上部倾斜导致的工程质量不合格问题,采用保护性控制爆破将上部倾斜部分钢砼桥墩予以拆除,同时保留下部未偏斜部分桥墩不受破坏。采用开设组合形状切口,预开定向窗、导向窗;设置组合高差卸荷槽,预伤钢筋弱化抗压抗拉能力为关键措施的控制爆破方案。方案实施取得了十分满意的效果,上部拟拆除部分桥墩顺利倾倒下坠,下部保留部分桥墩完好无损。采用保护性控制爆破技术能高效、安全地解决类似高耸钢砼桥墩(构筑物)部分拆除、部分保留利用的问题,并能取得可观的经济、社会效益。     

基于虚拟元-有限元耦合的隧道内道床干缩裂缝细观研究

为解释道床与盾构隧道管片产生脱空的现象，研究新混凝土在浇筑后由干燥收缩产生的裂缝机理。基于虚拟元推导任意多边形骨料的刚度矩阵格式，利用UEL子程序实现有限元与虚拟元的耦合计算，纯弯梁数值试验结果表明耦合法较有限元法计算效率明显提升，且具有较好的稳定性。在此基础上，建立细观尺度下新老混凝土的干缩数值模型，并通过圆盘干缩模型验证了模型参数。研究骨料和砂浆的应力分布、内部湿度与裂缝发展的对应关系以及新老混凝土表面和界面的应力发展。结果表明：①收缩过程中，骨料主要承受压应力作用，砂浆沿骨料边界的切线方向受骨料约束作用易形成收缩裂缝，在新混凝土表面首先出现大量微小裂缝，随后界面两端发生剥离; ②受表面下骨料的约束作用，新混凝土表面拉应力呈现“驼峰”分布。开裂后表面被划分为多个收缩区，收缩区边界受拉应力，内部受压应力；③界面的拉伸和剪切应力由两侧开始增加，并且随着界面剥离的增加不断内移。在界面内部未剥离区域内存在由界面附近骨料约束导致的局部压应力和剪切应力增大。     

异种铁素体耐热钢接头界面组织及其影响

综述了铁素体与铁素体异种金属焊缝（dissimilar metal welds，DMWs）接头界面组织及其影响。结果表明，在焊后热处理或运行温度下的铁素体钢DMWs接头的不均匀界面组织中，通常会形成脱碳层和增碳层。在铁素体钢DMWs焊接接头界面组织影响因素中，焊缝金属的化学成分有重要影响；焊后热处理规范（温度和时间）、工作温度下运行时间的影响较为突出；焊接工艺参数的影响亦不可忽略。异种钢接头界面处近缝区裂纹的产生，以及接头的蠕变强度随Larson Miller 参数增大而下降等不利影响，均为异种钢界面碳迁移行为所导致。焊缝成分控制法是接头界面组织控制或改善的必要条件，而脱碳层部位转移法能有效防止裂纹发生，亦是接头安全运行的重要工艺措施之一。     

温州某公轨共建高架车站结构设计

为了解决城市廊道资源的紧张和公共交通发展需求的矛盾,出现了轨道交通和快速路的共建型式,即公轨共建的复合型交通模式,以温州市域铁路S2线一期工程的人民路站为例,研究公轨共建高架车站的结构设计要点。首先,为降低浅层气体对桩基的承载力及沉降影响,对遇到局部浅层气体发育的基础设计提供了合理的解决方案。然后针对公轨共建一体化车站分别进行了多遇和罕遇地震作用分析,研究表明构件及整体指标满足规范要求。最后针对工程的一些关键技术,如快速路桥面体系的选型、超长结构温度应力的控制措施、轨道梁挠度及应力的控制、快速路桥面振动对车站的影响等进行了分析,并给出了具体的解决方案和指导意见。     

Life time prediction of self-supporting flame-sprayed alumina-rich coatings

Main objective of the presented research is the life time prediction of self-supporting flame-sprayed Al₂O₃- and Al₂O₃ -ZrO₂ -TiO₂-materials under constant load. The characteristic life time and its scatter were derived from stable crack growth tests and Weibull-statistics including the four-point-bending and ball-on-three-balls method. The potential life time was estimated in order to assess room-temperature handling and long term storage of self-supporting flame-sprayed alumina components. In terms of flexural strength, energy release, and subcritical crack growth parameters, distinct differences between both materials were shown. In turn, the characteristic life times only barely deviated from each other. From that the conclusion was drawn that life time performance under constant load application is governed by the characteristic flame-spray microstructure. However, advantages in the flame-spray processing of Al₂O₃ - ZrO₂ -TiO₂ are still given, attributed to its lower melting temperature.     

基于Abaqus的双裂纹不同间距对裂纹扩展速率的研究

扩展有限元法是近年经过大量运用的,在传统有限元的范围中求解不连续问题一种有效计算方法,它是基于单位分解的思想,在计算不连续问题时加入跳跃函数。以ABAQUS为平台,基于扩展有限元方法 (XFEM),以含双穿透型裂纹的有限宽板受横向拉伸载荷为力学模型,建立相应的裂纹尖端应力的有限元模型,研究焊接接头区域不同间距双裂纹相互作用对裂纹扩展速率的影响。结果表明:双裂纹间距的的大小并没有对裂纹的扩展速率产生影响。     

热轧圆钢热顶锻裂纹原因分析

热顶锻合格率是反映热轧圆钢实物质量的一个重要指标。在对国内外热轧圆钢热顶锻质量控制研究成果综述的基础上，对热轧圆钢的热顶锻质量进行了全面的调查、统计和试验研究，归纳了引起热轧圆钢热顶锻裂纹的常见原因，介绍了热顶锻裂纹分析步骤。通过对热顶锻裂纹的形貌和金相组织进行分析，阐述了引起热顶锻裂纹的冶炼因素和轧制因素，并进行了举例说明。     

超厚板TC4钛合金电子束焊接接头应力腐蚀敏感性

针对100 mm超厚板TC4钛合金电子束焊接接头，采用慢应变速率拉伸方法评价接头在人造海水中的应力腐蚀敏感性，分析接头的显微组织和断口形貌，对接头的腐蚀机制进行研究. 结果表明，室温条件下应变速率为ε=1×10-6 s-1时，母材在海水中未表现出应力腐蚀敏感性；焊缝上部、中部和下部具有轻微应力腐蚀敏感性. 焊缝在海水中发生阳极溶解，产生氢吸附，导致裂纹的萌生. 同时氢扩散诱导α'相界及α'相内发生位错塞积，进而使裂纹在更低的应力水平下发生扩展.     

Vibration analysis and identification of breathing cracks in beams subjected to single or multiple moving mass using online sequential extreme learning machine

In this paper, a novel approach was presented to vibration analysis and identification of breathing cracks in Timoshenko beam under single or multiple moving mass. Dynamic strain energies (DSEs) and translational accelerations in beam structures under moving mass were used as forward problem and application of an emergent learning algorithm called the online sequential extreme learning machine algorithm as inverse problem to predict crack depths and locations. To demonstrate the potential of the proposed vibration analysis over existing ones, two validation studies have been done. To evaluate the proposed method to identify breathing cracks, two examples, namely, clamped–clamped beam and two span continuous beams have been studied. Also, the effect of the discrepancy in stiffness between the finite-element model and the actual tested dynamic system has been investigated. Another examination has been performed in which moving mass with different speeds are utilized. Also, the effect of multi mass passing through the beam has been studied. The obtained results indicated that the proposed method could identify the breathing cracks existence and severity in the beam under moving mass using DSE and accelerations, which may be noisy or noise free.     

Toughness enhancement and equivalent initial fracture toughness of cementitious composite reinforced with aligned steel fibres

Based on theoretical analysis and numerical simulation, the impact of steel fibres on the stress intensity factor (SIF) at the crack tip for cementitious composite was studied. The enhanced toughness of steel fibre reinforced cementitious composite (SFRC) in resisting cracks was explained by the decrement of SIF caused by steel fibre inclusions at the crack tip of the composite. The equivalent initial fracture toughness was used to characterize the crack initiation of SFRC. A simplified method for determining the of SFRC was proposed based on a linear regression method. Fracture tests were conducted on three‐point bending notched beams with different steel fibre volume fractions and specimen sizes to study the crack initiation behaviour of aligned steel fibre reinforced cementitious composite (ASFRC). of ASFRC was calculated, and the size effect of was analysed. The results showed that slightly increased with the steel fibre volume fraction and gradually became stable. For the tested specimens, whose heights varied between 40 and 100 mm, the specimen size had little impact on the .