Thermal properties of hierarchical YSZ and LZO ceramic microspheres with multi-scaled voids investigated by using theoretical,experimental and simulation methods

Heat transfer within ceramic feedstock powders is still unclear, which impedes optimization of the thermal and mechanical properties of the thermal sprayed coatings. The microspheres (yttria-stabilized zirconia YSZ and lanthanum zirconate LZO) were prepared via the electro-spraying assisted phase inversion method (ESP). The thermal properties of the two ESP microspheres and a commercial hollow spherical powder (HOSP) were investigated by using theoretical, experimental, and simulation methods. Thermal conductivity of the single microsphere was estimated via a novel nest model that was derived from the Maxwell-Eucken 1 and the EMT model. Thermal conductivity of a single YSZ/LZO-ESP microsphere prepared at 1100–1200 °C was within 0.36–0.75 W/m K, which was ～ 20 % lower than that of a single YSZ-HOSP microsphere with a similar porosity. Heat flux simulation showed that high tortuosity around the multi-scaled voids of the ESP microsphere led to a more efficient decrease in thermal conductivity compared with total porosity.     

C105管桩混凝土设计参数取值的探讨

通过试验得出了C105混凝土100 mm×100 mm×100 mm立方体非标准试件抗压强度换算系数以及C105混凝土的标准方差和强度变异系数。采用理论计算,得到了棱柱体抗压强度与立方体抗压强度的比值α_c1,并与试验实测平均值进行了比较,验证了理论计算方法的可行性。此外,通过对比分析,探讨了直接外延法和引用公式法两种C105混凝土设计参数计算方法的正确性,研究结果可为C105管桩混凝土的设计和应用提供参考。     

Volatilization of fluorine in a CaO–SiO2–CaF2-based system with the substitution of Na2O with K2O

Cuspidine-based systems are used to control the crystallization in mold fluxes, which is enabled by CaF₂ additions. However, excess CaF₂ increases the corrosion of casting machines. Therefore, Na₂O and K₂O are added to the mold flux system to ensure an optimized crystallization and lubrication ability of the flux with the CaF₂ content. This study investigated the effect of substituting Na₂O with K₂O on the volatilization of fluorine in a CaO–SiO₂–CaF₂-based slag system at high temperatures. The substitution of Na₂O with K₂O was performed at 5 mol% intervals. The volatilization was observed by thermogravimetric analysis under several isothermal conditions. The mass loss was measured at a heating rate of 5, 10, and 20 K/min. As the temperature increased, the volatilization of the mixed samples increased. The activation energy was calculated using the Flynn–Wall–Ozawa and Kissinger–Akahira–Sunose methods. A kinetic analysis of the volatilization of fluorine was conducted using the calculated parameters and several known kinetic models. Consequently, the volatilization of the Na-rich sample was controlled by chemical reactions and that of the K-rich sample was identified to be controlled by a phase-boundary-controlled reaction. These results suggest that the addition of mixed alkali oxide promote the volatilization during the early stages of the reaction. From the post-experimental composition analyses, the remaining Na and K in the samples suggested a different mechanism for the Na and K volatilization. The volatilization of Na increased with time, whereas K volatilized easily during the beginning of the reaction.     

“方变圆”变径筒状结构滑模施工技术

为解决塔式光热的核心构筑物吸热塔"方变圆"变径超高筒体结构施工难题,选用一套可变形的滑模平台系统,通过操作系统上可调千斤顶支座、门架横向液压千斤顶装置、多处可调节模板角度和收缩模板的丝杆等,使得滑模根据施工需求可在一定的范围内调节模板倾角、间距,并逐步完成收缩变形,其理论滑模允许偏角20°,最终高效完成异形结构施工。该滑模系统刚度大、承载及堆料能力强、空间大、机械化程度高,施工操作简单,安全性高,适应沙漠极端环境。全过程仅需使用一套滑模体系,就能完成方形段、方变圆的变形段及圆形段施工,大大提高了施工效率,为类似环境下相似结构的施工提供了一定的参考。     

车用有机朗肯循环系统中计量泵的性能研究

在模拟车用有机朗肯循环(organic Rankine cycle,ORC)系统的工作环境下,设计并搭建以R123作为工质的液压隔膜计量泵性能测试平台。在额定转速(2900 r/min)下,通过调节液压隔膜计量泵的冲程(25%、50%、75%、100%)和出口压力,得到变工况下液压隔膜计量泵的特性曲线,并分析液压隔膜计量泵的关键参数对车用ORC系统性能的影响情况。结果表明:液压隔膜计量泵的流量受冲程影响,与出口压力基本无关。其输入功率和实际运行效率均随着冲程的增加而升高,最高分别可达523.91 W、88.27%。应用该液压隔膜计量泵的模拟车用ORC系统吸热量变化范围较广,系统热效率最高可达12.81%。液压隔膜计量泵可应用于车用ORC系统,通过调节液压隔膜计量泵的冲程和出口压力,可实现提高车用ORC系统热效率、增加系统净输出功率的目的。     

直流配网型混合动力系统在车客渡船上的应用

针对车客渡船动力负荷切换频繁,传统柴油机推进油耗高、排放和噪声大的问题,提出一种基于变速发电机组和超级电容储能装置的直流配网型混合动力系统。目前系统已成功应用于“江苏路渡3011”轮,实船运行数据显示:该混合动力系统不仅能达到较好的节油效果、降低排放,更在操控性、舒适性上优于传统的柴油机推进模式。     

油气管道缺陷漏磁检测有限元模拟

为了研究油气管道缺陷的漏磁信号特征，基于漏磁检测技术基本原理，采用有限元方法，应用ANSYS软件对含裂纹和气孔缺陷管道磁化后产生的漏磁场进行模拟仿真，得到了描述漏磁场特征的磁通密度径向和轴向分布曲线。通过改变裂纹和气孔的尺寸，得出这两种缺陷形式不同尺寸下的漏磁场分布规律。结果表明，随着裂纹深度增加，磁通密度径向、轴向分量的峰值强度均明显增大；在距管壁表面相同深度下，气孔缺陷磁通密度的峰值随孔径增加而显著增大；相同孔径时，气孔距表面越近，漏磁信号越强。为管道漏磁检测过程中的裂纹和气孔缺陷的特征识别提供了理论基础和实践依据。     

A novel method used to study growth of ash deposition and in situ measurement of effective thermal conductivity of ash deposit

Ash deposition always brings boilers some trouble due to fouling or slagging. In this paper, a completely controlled system was developed to study the growth of ash deposit. A novel sampling probe was designed to online measure the heat flux through ash deposit. Additionally, the thickness of ash deposit can be obtained by an online figure collecting system. The results of this research showed that as the thickness of ash deposit increased, the heat flux decreased. It was also found that at the initial stage of ash deposition when the thickness of ash deposit is approximately 1 mm, the heat flux through ash deposit had a sharp reduction. An effective method was attempted to situ measure the effective thermal conductivity of the ash deposit in the simulated combustion flue gas. It was found that temperature of the ash deposit layer had no obvious effect on its value. It was concluded that the structure of ash deposit had no obvious change in a short deposition time of 30 min with varied surface temperatures of the probe head between 400 °C and 600 °C.     

An up to date review of continuously variable speed wind turbines with mechatronic variable transmissions

As a promising and potential alternative to conventional fixed or variable speed wind turbines, continuously variable speed wind turbines (CVSWTs) with variable transmissions offer improved power efficiency and enhanced power control capabilities. The CVSWTs can be generally achieved by adapting mechatronic variable transmissions in the turbine drive train for continuously variable speed operations for wind turbines. Therefore, this paper serves to provide an up to date and exhaustive review of the CVSWTs with mechatronic variable transmissions such as mechanical variable transmission, electrical variable transmission, and power splitting transmission. In this paper, the analysis of CVSWTs with different mechatronic transmission topologies is performed regarding basic configurations, dynamic characteristics, control principles, and experimental or simulation results. Review results indicate the feasibility of applying CVSWTs with such mechatronic transmissions and highlight superiorities of the CVSWTs with power splitting transmission. The CVSWT with power splitting transmission will be particularly suitable for megawatt‐scale turbine systems and will hence increase the economic competitiveness of these turbines due to its large power capacity and high reliability. The directions or challenges for future investigations of CVSWTs with such mechatronic transmissions are also presented to foster in‐depth understanding of such CVSWTs and their control strategies.