Study on the removal of olefins from naphtha by clay loaded with trifluoromethanesulfonic acid

Journal of Porous Materials - In this work, a trifluoromethanesulfonic acid (TFOH) modified clay (TFOH-Clay) was developed for the removal of trace olefins in heavy naphtha. 5%TFOH-Clay can...     

Eco-friendly approach for preparation of hybrid silica aerogel via freeze drying method

Journal of Materials Science - In this paper, an eco-friendly method of producing hybrid silica aerogels by freeze-drying method (FD) is proposed. In the freeze-drying system, deionized water was...     

Surface energies in high-entropy carbides with variable carbon stoichiometry

The carbon vacancy in high-entropy carbides (HECs) has a significant impact on their physical and chemical properties, yet relevant studies have still been relatively few. In this study, we investigate the surface energies of HECs with variable carbon vacancies through first-principles calculations. The results show that the surface energy of the (1 0 0) surface of the stoichiometric HECs is significantly lower than that of (1 1 1) surface. With the decrease in carbon stoichiometry, the surface energies of both (1 0 0) and (1 1 1) surfaces increase gradually, which is mainly due to the weakening of covalent bonding and the decrease of metal Hirshfeld-I (HI) charges. However, the surface energy of (1 0 0) surface increases more quickly than that of (1 1 1) surface and will exceed that of (1 1 1) surface when the carbon stoichiometry decreases to a certain extent, which is primarily attributed to the greater decrease rate of metal HI charges of (1 0 0) surface.     

Suggestions to the article: medical professionalism research characteristics and hotspots

Scientometrics - The article published on 5 July 2021 is well-written and of interest. However, some improvements could be made, such as ten Tables/Figures can be shortened to highlight the focused...     

基于重要度排序的配电自动化终端优化布局方法

针对配电自动化终端优化布局问题，提出了一种基于重要度排序的终端优化布局方法。首先以等年值综合费用为目标函数，供电可靠性和投入产出比为双重约束建立了配电自动化终端优化布局模型。然后通过分析配电自动化终端对供电可靠性提升的影响，给出各个节点的“二遥”及“三遥”终端安装重要度定义及计算公式。最后采用枚举法确定最优终端安装数量，基于节点终端安装重要度排序确定终端的最优安装位置。该方法考虑了已布局节点对剩余节点终端安装重要度的影响，能够在降低计算量的同时兼顾布局合理性。运用所提方法RBTS-BUS2系统及扩充模型进行终端优化布局并与智能优化算法的布局结果进行对比，验证了本文方法的有效性及优越性。     

Oxidative characteristics and gel properties of porcine myofibrillar proteins affected by l-lysine and l-histidine in a dose-dependent manner at a low and high salt concentration

This study investigated the effects of l -lysine (Lys) and l -histidine (His) on the oxidative characteristics and gel properties of porcine myofibrillar proteins (MP). Results showed that Lys and His had a strong ferrous ion-chelating ability and hydroxyl radical-scavenging activity. Moreover, Lys and His inhibited the protein carbonyl formation and MP aggregation at 0.2 M and 0.6 M NaCl, respectively, in a dose-dependent manner. Furthermore, 2 and 4 mg mL⁻¹ Lys and His decreased the oxidation-induced loss of the tertiary structure of MP accompanied by the lower surface hydrophobicity. The water-holding capacity and gel strength of MP gels increased with increasing Lys and His concentrations due to more regular and lamellar structures with smaller and homogeneous pores at 0.6 M NaCl and more orderly crosslinking via fibrous filament at 0.2 M NaCl. In summary, Lys and His chelated the ferrous ions and scavenged hydroxyl radicals, decreased the oxidation-induced physicochemical changes, thus preventing oxidative damage during the formation of a three-dimensional gel network, which resulted in better gel quality.     

Fabrication of high-efficiency Yb:Y2O3 laser ceramics without photodarkening

High-efficiency Yb:Y₂O₃ laser ceramics were fabricated using the vacuum-sintering plus hot isostatic pressing (HIP) without sintering additives. High-purity well-dispersed nanocrystalline Yb:Y₂O₃ powder was synthesized using a modified co-precipitation method in-house. The green bodies were first vacuum sintered at a temperature as low as 1430°C and then HIPed at 1450°C. Finally, the samples were air annealed at 800°C for 10 h. Although no sintering aids were used, full density of the samples with excellent optical homogeneity and an inline transmission of 80% at 400 nm could be obtained. Moreover, photodarkening phenomenon was not detected in the ceramics. Preliminary laser experiment with the fabricated ceramics in a two-mirror cavity has demonstrated 32 W continuous-wave (CW) output at ∼1077 nm with an optical-to-optical conversion efficiency of 58.2%. To the best of our knowledge, this is so far the highest CW output power and optical-to-optical conversion efficiency achieved with the Yb³⁺-doped sesquioxide ceramics in a simple two-mirror cavity.     

Moderate temperature sintering of BaZr0.8Y0.2O3-δ protonic ceramics by A novel cold sintering pretreatment

The state-of-the-art protonic ceramic conductor BaZr_0.8Y_0.2O_3-δ (BZY20) requires an extremely high sintering temperature (≥1700 °C) to achieve the desired relative density and microstructure necessary to function as a proton conducting electrolyte. In this work, we developed a cold sintering pretreatment assisted moderate-temperature sintering method for the fabrication of high-quality pure BZY20 pellets. BZY20 pellets with high relative density of ~94% were fabricated with a final sintering temperature of 1500 °C (200 °C lower than the traditional sintering temperature). A comparison with BZY20 control samples indicated that the proper amount of BaCO₃ introduced on the BZY20 particle surface and the high green density achieved by cold sintering pretreatment were the main drivers for lowering the sintering temperature. The electrical conductivity measurement by electrochemical impedance spectroscopy showed that the as-prepared BZY20 pellets have a proton conductivity comparable to the state-of-the-art values. The cold sintering pretreatment outlined in this work has the potential to lower the sintering temperatures for similar types of protonic ceramic materials under consideration for a wide range of energy conversion and storage applications.     

Modification of the wood-plastic composite for enhancement of formaldehyde clearance and the 3D printing application

As the formaldehyde is one of the main indoor pollutants, the purpose of this study is to effectively remove indoor formaldehyde pollution by using environmentally friendly 3D printing ornaments. The wood 3D printing filaments cellulose/polylactic acid composite (Cellu/P) was selected as the starting material, and 3-aminopropyltriethoxysilane (APTES) was used for chemical modification to obtain a series of cellulose composite materials with amino groups. The modified composite materials (APTES@Cellu/P) were characterized by Fourier transform infrared, X-ray diffraction, scanning electron microscope, energy dispersive spectroscopy, thermogravimetric analysis, and mechanical tests, and a formaldehyde removal experiment was performed. The feasibility of 3D printing was evaluated, and the process of 3D printing-functionalized customized ornaments was proposed, and then a school emblem was used for modeling, printing, and surface modification. Compared with the commercially traditional activated carbon, 3D printing-customized ornaments of APTES@Cellu/P material has a better formaldehyde removal effect, and can even avoid the secondary pollution that is common to the activated carbon.     

地铁车辆空气制动管路保压试验的改进方案

分析了地铁车辆空气制动管路组装完毕后的保压试验操作过程,识别了其中的问题项点,提出了有针对性的优化改进方案,使保压试验结果准确可靠.