基于激光测距的机载光电成像系统目标定位

针对小型机载光电平台无法准确获取视轴指向问题，设计了一种基于激光测距的目标定位算法。利用机载光电侦察平台锁定跟踪目标的特性，对同一目标多次测量，采用激光测距装置获取目标与载机间的距离信息。根据WGS-84定义的地球椭球模型建立系统的测量方程。考虑到测量方程的非线性，利用扩展卡尔曼滤波对目标位置进行估计。该定位方法精度只受到GPS接收机定位精度和激光测距机测量精度的影响，目标定位误差与机载光电侦察设备视轴指向测量无关。采用蒙特卡洛法仿真分析载机位置测量误差及激光测距系统位置误差对目标定位的影响，结果显示该算法定位精度较高。采用飞行试验数据验证了该目标定位算法的有效性，在飞行高度8 000 m时，目标定位精度优于8 m。相比于传统定位算法，该方法可将定位精度明显提高。同时此定位方法易于部署，可操作性强，具有较大的应用价值。     

Highly efficient full-fluorescence organic light-emitting diodes with exciplex cohosts

Full-fluorescence organic light-emitting diodes (FOLEDs) with low cost and high efficiency are imperious demands for commercial process in flat panel display and lighting products. We fabricated a series of FOLEDs employing C545T and DCJTB as doped dyes and different exciplex blends as cohosts. The results proved that reverse intersystem crossing (RISC) efficiency of exciplex cohost has a significant effect on the device performance. Devices with TAPC:PIM-TRZ as cohost which possessed the highest RISC efficiency showed the best results. The green FOLEDs exhibited the maximum external quantum efficiencies (EQEs) approaching to 20%, the red FOLEDs exhibited EQEs over 10% and all the EQE roll-offs are less than 10% at 1000 cd m⁻², which are among the best reported results so far, suggesting these exciplex cohosts are promising for FOLEDs.     

在轨维修后端模块接口机构的研究

在轨维修可以大大的延长空间科学仪器的使用寿命,节省大量的经济成本。为了实现空间望远镜后端模块的在轨操作和更换,设计了一套与之对应的接口机构,能够解决在轨快速定位与安装。根据321运动学定位准则,详细介绍了该接口机构的内部组成和工作原理;然后把该接口机构与后端模块进行组件级有限元仿真,仿真结果表明一阶模态远高于整机基频可以有效地避免发射时候的共振;设计了一套平面内的工装来模拟后端模块,利用等效质量法对整个机构进行重力卸载;搭建实验平台,利用激光跟踪仪来测量整个后端模块的重复定位安装精度,实验数据表明,X,Y,Z 3个方向的重复平移定位误差分别为±5.58μm,±3.24μm及±3.63μm,优于总体指标±10μm;热实验结果表明整个机构可以完全释放由于温度变化产生的形变,具有很高的热稳定性;使入射光线和靶面的相对位置持续稳定,保证了较高的成像质量。为其他空间在轨维护装置提供强有力的参考价值。     

采用轮廓特征匹配的红外-可见光视频自动配准

为了精确地配准近平面场景下的红外-可见光视频序列,本文提出了一种基于轮廓特征匹配的自动配准方法,通过迭代匹配目标轮廓特征来解决异源图像中配准特征的提取和匹配难题。首先,采用运动目标检测技术获取目标轮廓,并由曲率尺度空间(CSS)角点检测算法提取轮廓特征点。此后,建立全局形状上下文描述子和局部边缘方向直方图描述子描述特征,从而实现可靠的特征匹配。来自不同时刻的匹配点对被保存在一个基于高斯距离准则的特征匹配库中。最后,为了克服近平面场景中目标深度变化的影响,本文结合前景样本随机抽样策略计算配准矩阵的损失函数,完成对全局配准矩阵的更新。在LITIV数据库上对方法进行实验验证,结果表明本文方法的配准精度优于当前先进的对比方法,在9个测试视频上的平均重叠率误差仅为0.194,与对比方法相比下降了18.5%。基本满足了近平面场景下红外-可见光视频序列配准的精度要求,且具有较高的鲁棒性。     

Highly stable and high power efficiency tandem organic light-emitting diodes with transition metal oxide-based charge generation layers

Tandem organic light-emitting diodes (OLEDs) have been studied to improve the long-term stability of OLEDs for 10 years. The key element in a tandem OLEDs is the charge generation layer (CGL), which provides electrons and holes to the adjacent sub-OLED units. Among different types of CGLs, n-doped electron transporting layer (ETL)/transition metal oxide (TMO)/hole transporting layer (HTL) has been intensively studied. Past studies indicate that this kind of CGL can achieve the desired efficiency enhancement, however, its long-term stability was reported not good and sometime even poor than a single OLED. This issue was not well addressed over the past 10 years. Here, for the first time, we found that this is caused by the unwanted diffusion of TMO into the underlying n-doped ETL layer and can be well resolved by introducing an additional diffusion suppressing layer (DSL) between them. Our finding will fully release the potential of TMO-based CGL in tandem OLEDs.     

Doping-free hybrid white organic light-emitting diodes with fluorescent blue,phosphorescent green and red emission layers

Industrialized white organic light-emitting diodes (OLEDs) currently require host-guest doping, a complicated process necessitating precise control of the guest concentration to get high efficiency and stability. Two doping-free, hybrid white OLEDs with fluorescent blue, and phosphorescent green and red emissive layers (EMLs) are reported in this work. An ultra-thin red phosphorescent EML was situated in a blue-emitting electron transport layer (ETL), while the ultra-thin green phosphorescent EML was placed either in the ETL (Device 1), or the hole transport layer (HTL) (Device 2). Device 2 exhibits higher efficiency and more stable spectrum due to the enhanced utilization of excitons by ultra-thin green EML at the exciton generation zone within the HTL. Values of current efficiency (CE), power efficiency (PE), and CRI obtained for the optimized hybrid white OLEDs fabricated through a doping-free process were of 23.2 cd/A, 20.5 lm/W and 82 at 1000 cd/m², respectively.     

X射线干涉光刻光束线关键光学元件热-结构耦合分析

为了保证上海光源X射线干涉光刻光束线的稳定性,减小热变形对实验结果的影响,对X射线干涉光刻光束线的3个关键光学元件——偏转镜、聚焦镜和精密四刀狭缝进行热-结构耦合分析。首先,计算偏转镜、聚焦镜和精密四刀狭缝所承载的功率密度;然后,建立其有限元模型;最后,获得光学元件的温度场和热变形的结果。结果表明,偏转镜和聚焦镜采用间接水冷方式可有效抑制热变形,冷却后的最大面形误差分别为7.2μrad和9.2μrad。精密四刀狭缝未冷却时,刀片组件温度介于271.56~273.27℃,刀口热变形为0.19 mm,直线导轨热变形为0.08 mm;经过铜辫子冷却后,刀片组件温度降至22.24~23.94℃,刀口热变形降至0.2μm,直线导轨热变形降至0.1μm;采用影像法和接触探头法测试后,刀口直线度、平行度和重复精度均满足技术要求。偏转镜、聚焦镜和精密四刀狭缝的热变形通过间接水冷和铜辫子的冷却方式可以得到很大程度的抑制,进而保证光斑质量。     

Improvement of alignment quality for FLC with mixing liquid crystal polymer

Ferroelectric liquid crystal (FLC) with I‐N*‐C* phase sequence is most attractive due to its continuous grey level and fast response; however, the alignment problem of two‐domains defect restricted its application. In this work, one kind of one terminal polymerizable nematic liquid crystal (NLC) mesogen was mixed to FLC to improve its alignment quality. Experimental results showed that mono‐domain uniform alignment of FLC can be obtained with mixing NLC polymer. With optimized concentration, the FLC devices could offer half‐V‐shaped electric‐optical characteristic of driving contrast of 182:1 and fast response of 300 µs even after polymerization. This work can provide one simple and effective method for fabricating stable I‐N*‐C* FLC devices.     

Performance improvement of conventional and inverted polymer solar cells with hydrophobic fluoropolymer as nonvolatile processing additive

The morphology of the photoactive layer critically affects the performance of the bulk heterojunction polymer solar cells (PSCs). To control the morphology, we introduced a hydrophobic fluoropolymer polyvinylidene fluoride (PVDF) as nonvolatile additive into the P3HT:PCBM active layer. The effect of PVDF on the surface and the bulk morphology were investigated by atomic force microscope and transmission electron microscopy, respectively. Through the repulsive interactions between the hydrophilic PCBM and the hydrophobic PVDF, much more uniform phase separation with good P3HT crystallinity is formed within the active layer, resulting enhanced light harvesting and improved photovoltaic performance in conventional devices. The PCE of the conventional device can improve from 2.40% to 3.07% with PVDF additive. The PVDF distribution within the active layer was investigated by secondary ion mass spectroscopy, confirming a bottom distribution of PVDF. Therefore, inverted device structure was designed, and the PCE can improve from 2.81% to 3.45% with PVDF additive. Our findings suggest that PVDF is a promising nonvolatile processing additive for high performance polymer solar cells.