木片筛余物高得率半化学法清洁制浆技术研究

以太阳纸业备料车间木片筛选碎料（筛余物）为原料，对其烧碱法半化学制浆的实验室工艺和生产试验进行了研究。结果表明，筛余物采用半化学法制浆可获得较高得率和环压强度的纸浆，且用碱量对纸浆性能有显著影响。相对8%NaOH （相对于绝干原料）化学预处理，采用14%NaOH化学预处理结合两段浆浓22%的高浓磨浆工艺，所制半化学浆抄造浆张的裂断长和环压指数分别达2.89 km和9.76 N·m/g，是前者的1.9倍和1.2倍，而且优于现用国内OCC废纸浆抄造浆张；生产试验得到的浆张性能指标与实验室相吻合，其中紧度和环压强度分别达到GB/T 13023—2008瓦楞芯（原）纸AA级和A级优等品要求。     

制浆造纸行业水污染全过程控制技术理论与实践

制浆造纸行业是我国水污染防治的重点,减排任务艰巨。在环境倒逼下,造纸行业加快淘汰落后产能和完善末端治理技术,污染控制取得了初步成效。但随着国家和地方环境治理由浓度控制走向总量控制、质量控制,原有技术的局限性难以满足解决水污染的更高要求,必须创新污染防治方法。本文介绍了制浆造纸行业水污染全过程控制的基本理论和内涵,并结合化学法制浆、化学机械法制浆、废纸制浆与造纸过程水污染防治工程实践,提出了解决制浆造纸行业水污染的对策,为推动行业绿色转型升级和高质量发展提供了支撑。     

Effect of neodymium substitution on crystalline orientation,microstructure and electric properties of sol-gel derived PZT thin films

Pb(Nd_xZr_0.52Ti_0.48)O₃ (PNZT) (x = 0%, 1%, 2%, 3%, 4%, 5%) thin films were prepared by sol-gel process to investigate the effects of neodymium substitution on crystalline orientation, microstructure and electric properties of lead zirconate titanate (PZT) films. X-ray diffraction (XRD) and scanning electron microscope (SEM) analysis showed that PNZT films with Nd doping concentration below 3% exhibited dense perovskite structure with (100) preferred orientation. The average grain size of PNZT films decreased as the Nd substitution increased. The maximum dielectric constant, remnant polarization and minimum coercive field were obtained in 2% Nd-doped PZT films. Fatigue resistance was also improved significantly with 2% Nd dopant.     

Influence of Different Additives on the Interaction of Quinolone Antibiotic Drug with Surfactant: Conductivity and Cloud Point Measurement Study

Conductometric and cloud point (CP) measurement studies have been performed to investigate the interaction of tetradecyltrimethylammonium bromide (TTAB) and Triton® X-100 (TX-100) with ciprofloxacin hydrochloride (CFH) in different solvents over the temperature range of 295.15–315.15 K. CFH is used for the treatment of various bacterial infections. The observed critical micelle concentration (CMC) values of TTAB were found to be reduced in the presence of electrolytes (Na₂SO₄/Na₃PO₄), and this reduction proceeds with the elevation of salt concentration. The order of the CMC of TTAB follows the trend: > >. The observed CMC values of TTAB were found to increase with increasing temperature and decrease with increasing concentration of CFH in aqueous medium. The values of Gibbs free energy of micellization () for the TTAB/TTAB + CFH mixture were found to be negative, implying spontaneous micellization. The estimated CP of TX-100 decreases with increasing concentration of TX-100 in aqueous medium. The CP values first decrease with increasing concentration of CFH and then increase at higher concentration of CFH almost in all cases investigated. The values of free energy of clouding were found to be positive in all cases studied implying that phase separation of TX-100 was nonspontaneous. The other thermodynamic parameters associated with the micellization of TTAB and the phase separation of TX-100 were estimated and explained.     

二元复合驱表面活性剂在油水界面的作用机理

用介观模拟方法对二元复合驱用表面活性剂分子在油水界面的分布形态进行了研究。发现十二烷基苯磺酸钠（SDBS）和辛基苯基聚氧乙烯醚（TX100）均分布在油水的界面，单独使用时对界面张力的降低均有一个极值，但两者协同作用时呈互补的状态，使油水界面处表面活性剂分子的分布密度增大，更多地占据油水界面层，从而能够更多地降低界面的界面张力；聚丙烯酰胺（HPAM）不能降低界面张力，但自身能够通过分子链的缠结向四周延伸，形成一个空间网状结构，将周围的油滴连结起来，使油分子更容易聚集。     

Recycled paperboard with a barrier layer for food contact: set-off during stacking or reeling. Analytical method and preliminary results

The use of recycled paperboard for packaging dry foods is in the interest of sustainability of resources, but in most applications, the food must be protected against contamination, such as by a functional barrier on the internal surface of the paperboard box. After application, the paperboard is usually stacked or reeled before making boxes. During this period, the food-contact surface of the barrier layer is in contact with the outer side of the paperboard, which may result in set-off and subsequent contamination of food. A method is described for the determination of this path of migration, based on the taped format also used for the measurement of the barrier efficiency. Recycled paperboard containing the three surrogate substances n-heptadecane, 4-methyl benzophenone and dipropyl phthalate was taped to the food-contact side of the barrier layer. Pressure onto the test packs did not seem to be a relevant parameter. After periods of interest, a piece of the paperboard with the barrier layer was extracted and analysed for the surrogate substances. Another piece may be brought into contact with silicone paper to simulate the transfer to food. After 2 weeks at 60°C (simulating about 1 year at 25°C), set-off and the transfer to the silicone paper exceeded 1% for all barrier materials tested, but after 6 weeks at 40°C (around half a year at 25°C), set-off remained below 1% for all barrier layers except a multilayer with polyethylene on the food-contact surface. The preliminary conclusion is that set-off should be taken seriously, but may be kept low enough to provide sufficient protection of the packed food.     

Nanofibrillation of a Bleached Acacia Pulp by Grinding with Carboxymethylation Pretreatment

In this study,carboxymethylation,which introduces carboxyl groups to hydroxyl sites in pulp fibers,was used as a pretreatment before mechanical nanofibrillation.The carboxyl group content of the pulp fibers was greatly affected by the dosage of chloroacetic acid and the reaction temperature.During the following fibrillation process,it was found that pulp fibers with higher carboxyl group content exhibited higher water holding capacities and smaller dimensions.A more homogenous structure with a higher amount of individual fibrils was also observed in FE-SEM images of pulp fibers with high carboxyl group content.This can be explained by a high ionic group content in the fiber wall resulting in lower delamination resistance,making the fibrils easier to separate.Carboxymethylation pretreatment as a facilitator of fibrillation in cellulosic pulps is an efficient way to obtain cellulose nanofibrils and consequently decrease the energy consumption of the process.     

某矿山充填料浆坍落度试验研究

充填采矿成为了目前的发展趋势,充填料浆的流动性在此过程中的作用不容小觑。对某矿山的料浆流动性进行坍落度试验研究。结果表明,塌落度随着充填料浆的灰砂比和料浆浓度的变化而变化,当料浆的浓度小于74%时,坍落度大于22.5 cm,其流动性明显有所改观,此时可实现管道自流输送的目的。低浓度的充填料浆有较好的流动性,但该情况下的充填体强度不能得到很好的保障,通过观察充填料浆在不同灰砂比下不同浓度的坍落度以及摊开的样子得出,浓度在68%之上的料浆具有良好的保水性,不会有粒级不同的颗粒相互分离或析水的不良情况,因此把充填料浆的浓度初设为68%~74%。相应的坍落度为22.5cm,完全摊开。     

Investigating the wicking behavior of micro/nanofibrous core-sheath PET–PAN yarn modified by dimethyl 5-sodium sulfoisophthalate

The present research aims at imparting an improved wicking ability to the recycled multifilament yarns by wrapping composite nanofibers to attain an efficient material for filtration purposes. Therefore, polyacrylonitrile nanofibers containing dimethyl 5-sodium sulfoisophthalate nanoparticles were wrapped around the recycled poly(ethylene terephthalate) yarn by means of a novel electrospinning technique. Several tests were performed to investigate the parameters affecting wicking rise and moisture regain of the samples. Taguchi method was used in two separate designs (with or without nanoparticles). Some factors such as polymer solution concentration, mass ratio of nanoparticles, take-up rate, and number of filaments were considered as the variable factors while yarn wicking rate and moisture regain were the response factors. It was found that the hydrophilic nature of nanoparticles together with the ultrafine structure of nanofibers provide yarns with enhanced wicking properties. Although solution concentration is the predominant factor in wicking rate of the yarns containing nanoparticles, the most effective factor in wicking rise and moisture regain for other cases is the number of filaments. The mechanism of nanoparticle effect on fluidic jet during electrospinning process is explained by theory of nanofluids stability which has never been validated experimentally in previous research studies. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48185.