纳米级超声造影剂的理论研究进展

为了克服超声造影剂中微米级气泡尺寸较大的局限性,大量研究人员对超声应用的替代造影剂(纳米级造影剂)进行了研究。随着生物纳米技术的飞速发展,纳米级超声造影剂在诊断与治疗领域有着广阔的发展前景。与超声造影剂中的微米级气泡相比,纳米级造影剂粒径较小,渗透能力极强,可以通过血管内皮间隙,进而可以实现血管外病变部位的显影。文中详细论述了超声造影剂在超声作用下的行为以及2种主要的纳米级造影剂:纳米气泡和纳米液滴造影剂,对其理论研究进展进行了总结,并提出了目前仍存在的一些问题及其未来的研究方向。     

CuO-SiO2气凝胶@TiO2纳米纤维无牺牲剂光催化还原CO2

采用溶胶-凝胶法制备CuO-SiO2复合气凝胶,通过在气凝胶孔道内填充TiCl4,然后将其气相水解,得到了在CuO-SiO2气凝胶表面生长了高结晶度的TiO2纳米纤维(CuO-SiO2@TiO2),纤维直径～16 nm.通过XPS、UPS、UV-Vis DRS、荧光光谱(PL)等表征了材料的结构及光电性能.结果表明,制备的CuO-SiO2@TiO2对可见光有明显吸收,且荧光强度较商用TiO2(P25)大幅降低,光生电子-空穴对更加稳定.再在纳米纤维上负载CuO,所得CuO-SiO2@TiO2/CuO在可见光区的荧光强度进一步增强.以300 W氙灯为光源,分别以CuO-SiO2@TiO2及CuO-SiO2@TiO2/CuO为催化剂,无牺牲剂条件下光催化还原CO2,4 h后甲醇产率分别为1304.0及1589.0μmol/g-cat,转换频率(TOF)分别为0.038及0.046 h–1.循环实验表明,纳米纤维具有较好的光催化稳定性,经过4次光催化循环实验后,CuO-SiO2@TiO2/CuO的保留率～94％,甲醇产率可达1472.0μmol/g-cat,TOF为0.042 h–1.     

多晶硅表面金属催化化学腐蚀法制绒研究现状

在多晶硅太阳能电池的生产过程中, 金刚线切割技术(Diamond wire sawn, DWS)具有切割速度快、精度高、原材料损耗少等优点, 受到了广泛关注。金刚线切割多晶硅表面形成的损伤层较浅, 与传统的酸腐蚀制绒技术无法匹配, 金属催化化学腐蚀法应运而生。金属催化化学腐蚀法制绒具有操作简单、结构可控且易形成高深宽比的绒面等优点, 具有广阔的应用前景。本文总结了不同类型的金属催化剂在制绒过程中的腐蚀机理及其形成的绒面结构, 深入分析和讨论了具有代表性的银、铜的单一及复合催化腐蚀过程及绒面结构和电池片性能。最后对金刚线切割多晶硅片表面的金属催化化学腐蚀法存在的问题进行了分析, 并展望了未来的研究方向。     

Theoretical study on a kind of cyclization mechanism of boron trichloride and hexamethyldisilazane to form the borazine ring for SiBCN ceramics precursor

Borazine rings act as a pivotal part in siliconboroncarbonitride ceramics (SiBCN) for high-temperature stability and great resistance to crystallization. A detailed investigation of the ring formation mechanism will guide the design and synthesis of SiBCN to meet application requirements under extreme conditions. Boron trichloride (BCl₃) and hexamethyldisilazane (HN(SiMe₃)₂) are common raw materials for the synthesis of precursors for SiBCN. In this paper, quantum chemical calculation was used to study the cyclization reaction mechanism between BCl₃ and HN(SiMe₃)₂ to form trichloroborazine (TCBZ) at the MP2/6-31G (d,p) level of theory. We discussed the structure properties, reaction pathways, energy barriers, reaction rates, and other aspects in detail. The results show that BCl₃ and HN(SiMe₃)₂ alternately participate in the reaction process, accompanied by the release of trimethylchlorosilane (TMCS), and that the entire reaction shows an absolute advantage in terms of energy. In the Step by step reaction, lower reaction barriers are formed due to the introduction of BCl₃ with more heat released compared to that for the introduction of HN(SiMe₃)₂. The final single-molecule cyclization and TMCS elimination steps are found to be faster compared to all previous bimolecular reactions.     

Strategies To Design Selective Histone Deacetylase Inhibitors

This review classifies drug-design strategies successfully implemented in the development of histone deacetylase (HDAC) inhibitors, which have many applications including cancer treatment. Our focus is on especially demanded selective HDAC inhibitors and their structure-activity relationships in relation to corresponding protein structures. The main part of the paper is divided into six subsections each narrating how optimization of one of six structural features can influence inhibitor selectivity. It starts with the impact of the zinc binding group on selectivity, continues with the optimization of the linker placed in the substrate binding tunnel as well as the adjustment of the cap group interacting with the surface of the protein, and ends with the addition of groups targeting class-specific sub-pockets: the side-pocket-, lower-pocket- and foot-pocket-targeting groups. The review is rounded off with a conclusion and an outlook on the future of HDAC inhibitor design.     

Vapor linker exchange of partially amorphous metal–organic framework membranes for ultra-selective gas separation

Metal–organic framework (MOF) membranes are promising for efficient separation applications. However, the uncontrollable pathways at atomic level impede the further development of these membranes for molecular separation. Herein we show that vapor linker exchange can induce partial amorphization of MOF membranes and then reduce their transport pathways for precisely molecular sieving. Through exchanging MOF linkers by incoming ones with similar topology but higher acidity, the resulted metal-linker bonds with lower strength cause the transformation of MOF membranes from order to disorder/amorphous. The linker exchange and partial amorphization can narrow intrinsic apertures and conglutinate grain boundary/crack defects of membranes. Because of the formation of ultra-microporous amorphous phase, the MOF composite membrane shows competitive H₂/CO₂ selectivity up to 2400, which is about two orders of magnitude higher than that of conventional MOF membranes, accompanied by high H₂ permeance of 13.4 × 10⁻⁸ mol m⁻² s⁻¹ Pa⁻¹ and good reproducibility and stability.     

Green sonochemistry fabrication of pure Gd2Sn2O7 nanoparticles with advanced photocatalytic efficiency for elimination of dye pollutions

The insufficiency of clean water sources has become a perilous tension for the future of the world that one of the eco-friendly and cost-effective solutions is the photocatalytic process for removal of artificial dyes and poisonous organic impurities. In the current research, an eco-friendly sonochemistry process was accomplished to gain Gd₂Sn₂O₇ (GSO) nanoparticles with progressive photo-catalytic proficiency. Lysine amino acid as a green capping agent and ethylenediamine (en) as an alkaline agent were utilized with effective surface categories aiming to manage the growth of formed nuclei with the design of spatial barriers around the metal cations and lastly, stop nano-sample accumulation. The figure and dimension of products was studied by various characterization procedures of spectroscopic and microscopic. The photo-degradation performances of the pure Gd₂Sn₂O₇, Gd₂Sn₂O₇/SnO₂ and Gd₂Sn₂O₇/SnO₂/Gd₂O₃ nanocomposites were tested to the removal of diverse synthetic dyes. The outcome of the type of dye, nano-catalyst composition, pH and scavenger kind was labeled on modifying ability of Gd-Sn-O nano-catalyst task. Optimized Gd₂Sn₂O₇/SnO₂/Gd₂O₃ nanocomposites have an efficiency of 98% for degradation of erythrosine dye that ^?OH radicals support photo-degradation of contamination.     

Entropy generation minimization on electromagnetohydrodynamic radiative Casson nanofluid flow over a melting Riga plate

Minimizing entropy generation is a technique that helps improve the effectiveness of real processes by studying the associated irreversibility of system performance of nanofluid. This study examines the entropy generation analysis of electromagnetohydrodynamic radiative Casson flow induced by a stretching Riga plate in a non-Darcian porous medium under the influence of internal energy change, Arrhenius activation energy, chemical reaction, and melting heat transfer. The thermophysical features of the fluid are assumed constant in most of the literature. However, this current research bridges this gap by considering viscosity, conductivity, and diffusivity as temperature-dependent variables. Also, the exponential decaying Grinberg term is used as a resistive force in this investigation due to the electromagnetic properties of the Riga plate in the momentum conservation equation. Some suitable dimensionless variables are introduced to remodel the transport equations into unitless ones and then solved numerically by employing Galerkin Weighted Residual Method. Analyses reveal that the Casson parameter declines the fluid velocity, while the existence of the melting parameter has the opposite effect. Also, this article includes some future recommendations.     

减水剂类型对赤泥—矿渣基地聚物注浆材料性能的影响及机理研究

针对赤泥等固体废弃物对环境危害性大且利用率低等问题,以碱激发赤泥-矿渣基地聚物注浆材料为 研究对象,研究了不同掺量的聚羧酸(PA)减水剂、醛酮缩合物(AKC)减水剂和萘系(N)减水剂对材料凝结时间、流动 性及强度等的影响,并通过 XRD、傅里叶红外光谱及 SEM 等设备对减水剂的作用机理进行研究。 结果表明:减水剂增 强了材料的流动性但降低了材料的剪切应力;N 和 PA 减水剂能缩短材料的凝结时间,但 AKC 减水剂会延长材料的凝 结时间;N 和 AKC 减水剂能提高材料的强度,但 PA 减水剂会降低材料的强度;N 减水剂对材料的综合性能提升效果 更加明显,其最优掺量为 0. 7%;减水剂对赤泥-矿渣基地聚物性能提升的作用机理主要是促进地聚合物凝胶的形成。 研究成果为拓展赤泥在工程上的使用途径和效率提供了理论指导。     

Preparation of faceted TaN grains by heating Ta-containing oxides in BN crucible with Na

Single-crystal grains of TaN were synthesized by heating Ta₂O₅, FeTa₂O₆, or FeTaO₄ in a BN crucible together with Na metal in an Ar atmosphere at 1100 °C. The BN crucible acted a solid source of nitrogen. Aggregates of columnar ε-TaN single crystals 10–150 μm in size were formed on the inner wall of the BN crucible when either Ta₂O₅ or FeTa₂O₆ was used. On the other hand, platelet-like single crystals of θ-TaN 1–50 μm in size were obtained from FeTaO₄. The results of wavelength-dispersive X-ray spectrometry indicated that the compositions of the ε-TaN and θ-TaN crystals were close to the stoichiometric ideal.