Study of metal assisted anisotropic chemical etching of silicon for high aspect ratio in crystalline silicon solar cells

Textured surface is commonly used to enhance the efficiency of silicon solar cells by reducing the overall reflectance and improving the light scattering. In this study, a comparison between isotropic and anisotropic etching methods was investigated. The deep funnel shaped structures with high aspect ratio are proposed for better light trapping with low reflectance in crystalline silicon solar cells. The anisotropic metal assisted chemical etching (MACE) was used to form the funnel shaped structures with various aspect ratios. The funnel shaped structures showed an average reflectance of 14.75% while it was 15.77% for the pillar shaped structures. The average reflectance was further reduced to 9.49% using deep funnel shaped structures with an aspect ratio of 1:1.18. The deep funnel shaped structures with high aspect ratios can be employed for high performance of crystalline silicon solar cells.     

Preparation and properties of nano-sized SnO2 powder

1　INTRODUCTIONSnO2isoneofthemainmaterialsusedingassensor.Becauseofthehumidityandgassensingfunction,itattractsmoreandmoreattentions.Butthepresentproblemishowtoimprovethestabilityandsensibilityofgassensor.Researchershavetakenmanymeasurestoresolvethisproble…     

Processing and microstructure of non-oxide ceramic fibres

Research and development efforts on high-temperature, oxidation-resistant fibres have increased over the past decade due to the demand for light-weight, stiff and strong composite materials in aerospace applications. Varieties of ‘high-performance’, continuous, non-oxide fibres with low-density, high tensile strength and tensile modulus have been developed either from organic precursors or via chemical vapour deposition for fabrication of ceramic matrix composites. Fibres derived from polymer precursors (e.g. Nicalon, Tyranno, HPZ) are small in diameter (compared to CVD monofilaments) and are ideally suited for ceramic composites. Processing, microstructural stability and mechanical properties of these newly developed SiC and Si₃N₄ base fibres are briefly reviewed in this paper.     

超细Fe3O4粒子表面包覆酞菁钴性质研究

本文研究了合成载氧体的金属有机化学液相淀积法制造工艺，所得产物经ＴＥＭ、ＸＰＳ、Ｍｏｓｓ－ｂａｕｅｒ谱和Ｂ－Ｈ仪等手段，研究了它的结构和磁性能。实验表明，酞青钴以薄层形式包覆在Ｆｅ＿３Ｏ＿４的表面，封闭了Ｆｅ＿３Ｏ＿４的表面孔洞，稳定了Ｆｅ＿３Ｏ＿４的物相，增强了磁性能。     

孤岛油田西区聚合物驱开发研究

孤岛油田西区注聚区1997年3月投入注聚后，高渗层得到有效封堵，吸水剖面得到明显改善。注聚期间，通过实施注聚区外围水井降水或停注、油井放大生产压差和调整注聚井注入速度等开发措施，扩大了聚合物波及体积，聚合物驱取得了明显效果。     

氧化铝生产过程结疤溶解的研究

针对氧化铝生产过程结疤现象。研制出一种新型清洗溶剂，溶垢率可达95%，清洗效果达到《工业设备化学清洗质量标准》要求。     

深孔钻机水刹车传动机构的设计改进

针对深孔钻机水刹车传动机构原设计结构中存在的问题进行分析、研究、并对机构进行了改进，满足了钻机绞车的各项性能指标和技术要求。     

医用聚氯乙烯材料的表面光接枝改性

研究了在不排氧氛围下 ,紫外光照射 ,以二苯甲酮 (BP)为光引发剂 ,甲基丙烯酸缩水甘油酯(GMA)在医用聚氯乙烯 (PVC)薄膜表面的气相接枝聚合。探讨了反应条件对接枝结果的影响 ,并用正交法指出了影响因素的显著性。用傅立叶红外 (FT- IR)、水接触角作为接枝改性结果的表征。FT- IR谱图表明 GMA已接枝到 PVC膜表面。水接触角由接枝前的 78°下降到 5 4°     

Inhibition of acid rock drainage from uranium ore waste using a conventional neutralization and precipitation treatment

Glass columns (length 50 cm, i.d. 4 cm) containing 900 g of uranium ore waste were subjected to a three-step process: (1) acid drainage generation, (2) neutralization and precipitation treatment and, again, (3) acid drainage generation. In the first acid generation step, lasting about one year, different variables (pyrite addition, inoculation and irrigation solution) were tested by measuring effluent pH, redox potential, total iron and sulphate. Conditions of acid generation were satisfactorily reproduced, reaching stable pH values around 2.0 that were determined mainly by pyrite addition and the type of irrigation solution used (distilled water or ferrous sulphate). The neutralization and precipitation treatment consisted of alternating irrigations of a neutralizing solution (CaO saturated plus NaOH) and a precipitating solution (ferric sulphate saturated). This treatment caused accumulation of basic iron sulphate and iron oxide precipitates according to SEM studies. After this treatment, the barrier effect created by the reaction products was checked, using irrigation solutions similar to the first step. The effluents collected showed higher pH and lower redox potential, total iron and sulphate values than those observed before the treatment, evidencing inhibition of acid drainage generation.     

旋风分离器结构改进的研究

根据旋风分离器的工作原理及应用特点 ,分析了影响旋风分离器分离效率的因素及结构存在的问题 ,并提出了改进措施 ,即内管外壁增设螺旋翼片 ,扩散形锥体改为悬挂挡板。通过实验观察 ,改进结构的旋风分离器分离效率比常规旋风分离器高。实践证明 ,对于密度差异较小的非均相物系的分离 ,只要对旋风分离器作适当改进 ,仍能取得令人满意的效果 ,这大大拓宽了旋风分离器的应用领域