Visible light active Cu-doped iron oxide for photocatalytic treatment of methylene blue

In recent work, pure α-Fe₂O₃ (F-1) and series of 5% Cu doped Fe₂O₃ (CF-5) , 10% Cu doped Fe₂O₃ (CF-10) and 15% Cu doped Fe₂O₃ (CF-15) nanoparticles by facile chemical coprecipitation method were synthesized to study the effect of concentration of doping for photocatalytic activity. As prepared F-1, CF-5, CF-10, CF-15 nanoparticles were subjected to X-ray diffraction (XRD) and Fourier transform infra-red (FTIR) techniques to analyse the structural and functional groups features. These characterization techniques confirmed the successful doping of Cu ²⁺ ions in α-Fe₂O₃. The crystallite size of synthesized samples was calculated by Scherrer formula. Gradually decline in crystallite size from 18 to 15 nm was observed for undoped to doped samples. Scanning electron microscopic (SEM) analysis expressed that doping of Cu reduced the aggregation of particles and enhanced the surface area of nanoparticles. UV–Visible spectroscopic analysis of synthesized samples was used to calculate the bandgap energy of F-1, CF-5, CF-10, CF-15 nanoparticles i.e., 2.0, 1.7, 1.5, 1.4eV respectively. Narrowing bandgap energy of doped hematite supported to perform excellent photocatalytic activity. Maximum degradation of methylene blue was recorded via CF-10 within 140 min. Higher degradation rate of methylene blue by optimal concentration of CF-10 is due to effective electron trapping ability of photocatalyst.     

New food safety challenges of viral contamination from a global perspective: Conventional,emerging, and novel methods of viral control

Food- and waterborne viruses, such as human norovirus, hepatitis A virus, hepatitis E virus, rotaviruses, astroviruses, adenoviruses, and enteroviruses, are major contributors to all foodborne illnesses. Their small size, structure, and ability to clump and attach to inanimate surfaces make viruses challenging to reduce or eliminate, especially in the presence of inorganic or organic soils. Besides traditional wet and dry methods of disinfection using chemicals and heat, emerging physical nonthermal decontamination techniques (irradiation, ultraviolet, pulsed light, high hydrostatic pressure, cold atmospheric plasma, and pulsed electric field), novel virucidal surfaces, and bioactive compounds are examined for their potential to inactivate viruses on the surfaces of foods or food contact surfaces (tools, equipment, hands, etc.). Every disinfection technique is discussed based on its efficiency against viruses, specific advantages and disadvantages, and limitations. Structure, genomic organization, and molecular biology of different virus strains are reviewed, as they are key in determining these techniques effectiveness in controlling all or specific foodborne viruses. Selecting suitable viral decontamination techniques requires that their antiviral mechanism of action and ability to reduce virus infectivity must be taken into consideration. Furthermore, details about critical treatments parameters essential to control foodborne viruses in a food production environment are discussed, as they are also determinative in defining best disinfection and hygiene practices preventing viral infection after consuming a food product.     

Dynamic simulation and lifecycle assessment of hydrogen fuel cell electric vehicles considering various hydrogen production methods

In this research study, a real model of a hydrogen fuel cell vehicle is simulated using Simcenter Amesim software. The software used for vehicle simulation enabled dynamic simulation, resulting in more precise simulation. Furthermore, considering that fuel cell degradation is one of the significant challenges confronting fuel cell vehicle manufacturers, we examined the impact of fuel cell degradation on the performance of hydrogen vehicles. According to the findings, a hydrogen vehicle with a degraded fuel cell consumes 14.3% more fuel than a fresh fuel cell hydrogen vehicle. A comprehensive life cycle assessment (LCA) is also performed for the designed hydrogen vehicle. The results of the hydrogen vehicle life cycle assessment are compared with a gasoline vehicle to fully understand the effect of hydrogen vehicles in reducing air emissions. The methods considered for hydrogen production included natural gas reforming, electrolysis, and thermochemical water splitting method. Furthermore, because the source of electricity used for electrolysis has a significant impact on the life cycle emission of a hydrogen vehicle, three different power sources were considered in this assessment. Finally, while a hydrogen vehicle with a degraded fuel cell emits lower carbon dioxide (CO₂) than a gasoline vehicle, the emitted CO₂ from this vehicle using hydrogen from electrolysis is approximately 25% higher than that of a new hydrogen vehicle.     

Evaluation of in-situ formed La2O3–TiO2–La2O2CO3 nanocomposite photocatalyst for H2 production

The photocatalytic evolution of H₂ over La₂O₃ decorated TiO₂ catalyst was examined under solar light. It was observed that during the course of the reaction, the transformation of La₂O₃/TiO₂ into La₂O₃–TiO₂–La₂O₂CO₃ occurred and these species effectively suppressed electron-hole pair recombination by forming electron trapping centres on the surface, resulting in an increased visible light absorption and improved H₂ yield. The 2 wt%La₂O₃/TiO₂ nanocomposite demonstrated better H₂ yield (～8.76 mmol (g_cat)^?1) than the bare TiO₂ (～1.1 mmol (g_cat)^?1). The catalyst was stable even after several consecutive recycles with no substantial loss of hydrogen production rate. The H₂ rates were correlated with the physicochemical characteristics of the catalysts examined by BET–SA, H₂-TPR, XRD, UV-DRS, Raman spectroscopy, FTIR, HRTEM, EPR and PL spectroscopy.     

Effect of geotextile ageing and geomembrane surface roughness on the geomembrane-geotextile interfaces for heap leaching applications

A series of large scale direct shear experiments is used to investigate the effect of the geomembrane (GMB) surface roughness, geotextile (GTX) properties, and GTX ageing, on the GMB-GTX interface shear behaviour. Interfaces involving smooth, coextruded textured, and structured surface GMBs underlying four different nonwoven needle-punched staple fibres (GTXs) with mass per unit areas between 200 and 2400 g/m², and a geocomposite drain (GCD) are examined at normal stresses between 250 and 1000 kPa. The results showed that the interlocking between the GMB and GTX increased with increasing the GMB asperity height and/or decreasing the mass per unit area of the GTX. For the interfaces that involved GTXs preaged prior to the shear box experiments for up to 2 years at 85 °C, it was found that the 2400 g/m² heat bonded two-layered GTX exhibited internal shear failure at low shear displacements. However, all the highly aged single layered GTXs showed an increase in the peak interface friction angles with the increase in their ageing. For these single layered GTX, the results suggest that assessing the interface friction angles using unaged GTXs for the stability analysis is conservative as long as the GTX remains intact in the field.     

Liquefaction behavior of fiber-reinforced calcareous sands in unidirectional and multidirectional simple shear tests

A study on the liquefaction resistance of calcareous sands reinforced with polypropylene fibers was reported. Stress-controlled cyclic simple shear tests were conducted on specimens prepared at a relative density of 50%, with and without fiber reinforcements. The liquefaction behavior was investigated by considering the effects of fiber contents ranging from 0% to 1%, fiber lengths varying from 3 mm to 12 mm and loading patterns. The results indicated that increasing fiber content and fiber length resulted in a decrease in the deformation, a reduction in pore pressure accumulation rate, and improved the liquefaction resistance of calcareous sands. Additionally, the risk of soil liquefaction could be significantly reduced when the fiber content was greater than 0.8%. The multidirectional loading had a considerable effect in reducing the liquefaction resistance compared to unidirectional loading. Further, the stiffness degradation of calcareous sands decreased with increasing fiber content and fiber length. The pore pressure generated in the cyclic tests was analyzed and was found to be affected by fiber content. A pore pressure prediction model was proposed to obtain the pore pressure characteristics of fiber-reinforced calcareous sands under various fiber content conditions.     

菌酶协同改善花生粕的饲用品质

花生粕是重要的蛋白饲料原料，但由于其氨基酸不平衡，特别是精氨酸与赖氨酸比例严重失衡（精氨酸与赖氨酸含量比值在3~4，理想的精氨酸与赖氨酸含量比值为1.0），限制了其在动物养殖中的应用。研究了复合酶预处理结合乳酸菌发酵花生粕对其品质的改善。结果表明：经菌酶协同处理后，花生粕粗蛋白质含量由46.4%提高至506%，大分子蛋白明显降解为小分子蛋白，酸溶蛋白质含量由2.3%提高至17.8%，多肽含量由1.6%提高至15.7%，蛋氨酸和赖氨酸含量分别提高了77.1%和42.0%，精氨酸降解率为18.7%，精氨酸与赖氨酸含量比值从3.7降低至2.1，总酸含量由06%提高到4.7%，其中乳酸含量由0.64 mg/g提高至14.63 mg/g。菌酶协同处理后的花生粕抗氧化性明显增强，其中每克菌酶协同处理后的花生粕对羟自由基的清除能力与171.6 mg VC相当，比花生粕（与47.6 mg VC相当）提高了2.6倍。     

Construction of CaTiO3 nanosheets with boron nitride quantum dots as effective photogenerated hole extractor for boosting photocatalytic performance under simulated sunlight

Herein, titanate-based perovskite CaTiO₃ nanosheets were successfully designed via boron nitride quantum dots (BNQDs) to fabricate CaTiO₃/BNQDs catalyst. The as-fabricated composite catalysts were analysed by transmission electron microscope (TEM), scanning electron microscopy coupled with energy dispersive spectrometry (SEM-EDS), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR), X-ray diffraction (XRD), UV–vis spectroscopy (UV-DRS), photoluminescence (PL) and electrochemical impedance spectroscopy (EIS) techniques. SEM-Mapping analysis showed that the boron and nitrogen elements dispersed well over the CaTiO₃ surface which was useful for building electronic channels for rapid transport of photo-induced charge pairs. TEM images verified the attachment of BNQDs around the surface of host CaTiO₃ forming intimate interface while the distribution of chemical states was observed by XPS analysis demonstrating strong coupling effect between BNQDs and CaTiO₃ through Ti–O–N and Ti–O–B bonds. Moreover, PL and light absorption properties enhanced with the quantum confinement effect of BNQDs. As expected, the photocatalytic degradation rate of CaTiO₃/BNQDs was increased to k_app = 0.015 min^{? 1} with optimum BNQDs loading, which was 2.31 times folder than that of bare CaTiO₃ (0.006 min^{? 1}). The enhanced photocatalytic efficiency was observed for CaTiO₃/BNQDs than pristine perovskite on account of formation of electron tapping sites, decreased band gap energy and hindered recombination rate. On the other hand, in the presence of H₂O₂, the degradation percentage increased from 88.5% to 92.1% at the end of 120 min of irradiation while 96.8% of TC was quickly degraded within 60 min after activating with peroxymonosulfate which created strong sulphate radicals. Radical trapping tests indicated that the photo-generated holes were the primary active species in the photocatalytic mechanism. Moreover, CaTiO₃/BNQDs catalyst showed excellent stability in recycling tests. Besides, the possible degradation mechanism was proposed. This study shed light on the significance of BNQDs in the enhancement of the photocatalytic activities of titanate-based perovskite for effective degradation of tetracycline antibiotic in contaminated water.     

The thermochromic characteristics of Zn-doped VO2 that were prepared by the hydrothermal and post-annealing process and their polyurethane composite films

In this paper, Zn-doped VO₂ nanoparticles have been successfully fabricated by a two-step hydrothermal-annealing process, and the thermally induced visible light transmittance enhancement of Zn-doped VO₂ has been studied for the first time. It is found that Zn-doped VO₂ not only exhibits excellent solar modulation ability (ΔT_sol = 15.27%) but also can reduce the phase transition temperature and increase the visible light transmittance after the heat-induced phase transition (ΔT_lum=+5.78%). Moreover, with the increase of Zn doping concentration, the phase transition temperature (T_c) and phase transition hysteresis (ΔT) both decrease. It is shown that the Zn-doped VO₂-PU films not only have good solar light modulation ability and properties of improving visible light transmission after phase transition, but also have good durability. The research result is of great significance for improving the visible light transmittance after phase transition and realizing the practical application of VO₂ in the field of smart windows.     

Alkylated indolo[3,2,1-jk]carbazoles as new building blocks for solution processable organic electronics

A facile strategy for the introduction of tert-butyl and hexyl chains to the indolo[3,2,1-jk]carbazole scaffold is presented. With these building blocks six materials based on three different 4,4′-bis(N-carbazolyl)-1,1-biphenyl derivatives with varying degree of planarization were prepared. Characterization of the materials showed that the alkyl chains have only minor effects on the photophysical properties of the compounds. In contrast, thermal robustness towards decomposition and electrochemical stability are increased by the introduced alkyl chains. Detailed investigation of the solubility in five different solvents revealed that the incorporation of the alkyl chains increases the solubility significantly. The increased solubility of the materials allowed the application as host materials in red, green and sky-blue solution processed phosphorescent organic light emitting diodes. Hence, this work presents the first solution processed light emitting devices based on the indolo[3,2,1-jk]carbazole scaffold.