基准平面垂直断面法在爆破漏斗试验中的应用

系统阐述了基准平面垂直断面法在爆破漏斗试验中测量爆破漏斗体积的基本原理,并将隧道激光断面仪应用于金厂河矿1 750 m水平15^#采场底部切割巷道爆破漏斗试验爆破漏斗体积测量中。通过与传统体重法等计算法所得漏斗体积分析比较,结果表明基于隧道激光断面仪与3D Mine软件分析的基准平面垂直断面法实用性强、操作方便、结果直观可靠,达到试验预期目的。     

基于BIM超高层密集布筋区埋入式型钢混凝土柱脚施工技术

以漳州市某超高层项目为例,针对超高层密集布筋区埋入式型钢柱脚与钢筋的深化设计、地脚螺栓的定位预埋、型钢柱脚支撑体系设计、节点钢筋穿插连接施工、埋入式型钢柱脚安装等方面,提出切实可行的施工方法,解决了埋入式型钢混凝土柱脚的地脚螺栓精准预埋、与底板密集钢筋穿插连接施工、悬空支撑稳定等一系列施工技术难题,既满足了设计方案的要求,又可为类似工程提供借鉴。     

Experimental study on free and submerged multi-jets

The flow characteristics of the hydraulic jump due to parallel jets are different from the classical jump emerging from a single gate. Due to the highly complex flow field at the downstream pool, deciding about the tailwater measuring location is a challenging issue affecting the flow measuring accuracy. Experiments are conducted herein, on different parallel jets’ configurations for both free and submerged flow conditions. To quantify the flow uniformity, for any downstream cross section, the associated momentum correction factors, β₂, were estimated for the free-flow condition. It is found that β₂-values depend significantly on the measuring location, and consequently the available conjugated depths relationship results in poor estimation when measuring location moves downstream. Employing Buckingham analysis, a general formula is proposed to calculate the momentum correction factors associated with the free hydraulic jump at different downstream measuring locations. The experimental results of this study indicated that such a formula enhances distinguishing between free and submerged flow conditions of the gates installed in parallel. Finally, a dimensionless stage-discharge formula is presented to predict the submerged flow rate through parallel gates of different gate openings and widths.     

Multi-objective iterative optimization algorithm based optimal wavelet filter selection for multi-fault diagnosis of rolling element bearings

Rolling element bearings (REBs) play an essential role in modern machinery and their condition monitoring is significant in predictive maintenance. Due to the harsh operating conditions, multi-fault may co-exist in one bearing and vibration signal always exhibits low signal-to-noise ratio (SNR), which causes difficulties in detecting fault. In the previous studies, maximum correlated kurtosis deconvolution (MCKD) has been validated as an efficient method to extract fault feature in the fault signals. Nonetheless, there are still some challenges when MCKD is applied to fault detection owing to the rigorous requirements of multiple input parameters. To overcome limitation, a multi-objective iterative optimization algorithm (MOIOA) for multi-fault diagnosis is proposed. In this method, correlated kurtosis (CK) is taken as a criterion to select optimal Morlet wavelet filter using the whale optimization algorithm (WOA). Meanwhile, to further eliminate the effect of the inaccurate period on CK, the update process of period is incorporated. After that, the simulated and experimental signals are utilized to testify the validity and superiority of the MOIOA for multiple faults detection by the comparison with MCKD. The results indicate that MOIOA is efficient to extract weak fault features even with heavy noise and harmonic interferences.     

Drag Power Loss Investigation in Cylindrical Roller Bearings Using CFD Approach

In high-speed rolling element bearings, the drag forces can be prominent and it is demonstrated in this investigation that the classical models may not be appropriate for correctly estimating this power loss contribution. A modification of the models is thus proposed, including the usual drag forces formulation relying upon the drag coefficient to be evaluated from a numerical computational fluid dynamics (CFD) approach. A three-dimensional approach that considers both the rings and the cylinder ends seems the only adequate approach to be used because a two-dimensional approach predicts a drag coefficient value that is too low. When using the former computed drag coefficient for the evaluation of the total power losses, high values of oil volume fraction must be employed to recover the measured power losses.     

Benchmark experiment of large-angle scattering reaction cross section of iron at 14 MeV using two shadow bars – Comparison of experimental results with ENDF/B-VIII –

ABSTRACT

It is important to perform neutron transport simulations with accurate nuclear data in the neutronics design of a fusion reactor. However, absolute values of large-angle scattering cross sections vary among nuclear data libraries even for well-examined nuclide of iron. Benchmark experiments focusing on large-angle scattering cross sections were thus performed to confirm the correctness of nuclear data libraries. The series benchmark experiments were performed at a DT neutron source facility, OKTAVIAN of Osaka University, Japan, by the unique experimental system established by the authors’ group, which can extract only the contribution of large-angle scattering reactions. This system consists of two shadow bars, target plate (iron), and neutron detector (niobium). Two types of shadow bars were used and four irradiations were conducted for one experiment, so that contribution of room-return neutrons was effectively removed and only large-angle scattering neutrons were extracted from the measured four Nb reaction rates. The obtained experimental results were compared with calculations for five nuclear data libraries including JENDL-4.0, JEFF.-3.3, FENDL-3.1, ENDF/B- VII, and recently released ENDF/B-VIII. It was found from the comparison that ENDF/B-VIII showed the best result, though ENDF/B-VII showed overestimation and others are in large underestimation at 14 MeV.     

圆形截面柱的振动台试验及分析

进行了圆柱振动台试验,对模型的加速度反应数据进行获取。试验表明,随着地震的加速度峰值的不断增加,圆柱顶部加速度极值不断增加。柱顶的加速度响应有着增大的趋势,且极值比输入的加速度的极值有一定的放大。     

高低孔爆破处理高陡边坡的技术分析

针对前期规划不当,大宝山露天矿877 m平台高陡边坡局部存在难以采用预裂爆破技术进行处理的情况,决定采用高低孔爆破处理技术。为了解决这一难题,首先分析了高低孔的相对内涵,并对高低孔孔深计算公式进行了简单推导,然后通过公式计算得到了高低孔的孔深。在施工阶段,为了确保低孔的实施效果,两排低孔分区域使用同段别毫秒延时雷管,晚于高孔起爆。实践表明,处理后的平台平整度良好,坡面较为稳定,对高陡边坡采用高低孔爆破处理具有可行性,效果较好,可为类似边坡处理提供新思路。     

基于旋滚比的电主轴轴承预紧力优化研究

为研究不同工况下轴承预紧力对电主轴轴承动力学的影响规律，基于外轨道控制理论,建立了一种以旋滚比可优化的轴承预紧力动力学模型。通过分析高速状态下滚动体载荷和特征参数动态变化过程，构建综合考虑滚动体滚动、自旋转、陀螺运动和离心力的轴承动力学分析模型，在此基础上，计算旋滚比动态变化结果；研究Jones发现的阈值与旋滚比之间的动态定量映射关系；以轴承滚动体打滑状态为优化目标，使用MATLAB仿真分析不同工况下轴承最佳预紧力。建模分析表明，轴承旋滚比大小可以反映轴承预紧效果，也可实现轴承预紧力动态定量优化。