Analysis of adhesively bonded CFRE composite scarf joints modified with MWCNTs

The main objective of the present work is to improve the performance of bonded joints in carbon fiber composite structures through introducing Multi-Walled Carbon Nanotubes (MWCNTs) into Epocast 50-A1/946 epoxy, which was primarily developed for joining and repairing of composite aircraft structures. Results from tension characterizations of structural adhesive joints (SAJs) with different scarf angles (5–45°) showed improvement up to 40% compared to neat epoxy (NE)–SAJs. Special attention was considered to investigate the performance of SAJs with 5° scarf angle under different environments. The tensile strength and stiffness of both NE-SAJs and MWCNT/E-SAJs were dramatically decreased at elevated temperature. Water absorption showed a marginal drop of about 2.0% in the tensile strength of the moist SAJs compared to the dry one. Cracks initiation and propagation were detected effectively using instrumented-SAJs with eight strain gauges. The experimental results agree well with the predicted using three-dimensional finite element analysis model.     

A methodology for the estimation of transverse failure strength of an oxidized lamina from isothermal aging studies

Surface oxidation and ensuing damage substantially decrease the service life of High Temperature Polymer Matrix Composite (HTPMC) structures. Oxidative degradation behavior of composites is strongly dependent on the coupling between chemical and mechanical responses of the material. In a composite lamina, the onset of damage and subsequent coupled acceleration of both damage and oxidation are controlled by the transverse failure strength of the oxidized regions. The direct measurement of this strength from experimentation is challenging and cumbersome. A model-based methodology for estimating the mean transverse failure strength of the oxidized regions of a unidirectional composite is described in this paper. As the strength of the oxidized region is expected to show a high-degree of spatial variability, the estimated mean is shown to be relatively insensitive to the effect of strength variance. The developed methodology is illustrated with isothermal aging data available for a typical high-temperature composite system.     

Kinetics of light-induced degradation in compensated boron-doped silicon investigated using photoluminescence and numerical simulation

We use photoluminescence to observe light-induced degradation in silicon in real time. Numerical simulations are used to match our results and lifetime decay data from the literature with theoretical models for the generation of the light-induced boron–oxygen defects. It is found that the existing model of the slowly generated defect SRC, where its saturated concentration is a function of the majority carrier concentration, does not explain certain results in both p- and n-type samples. A new model is proposed in which the saturated SRC concentration is controlled by the total hole concentration under illumination.     

Experimental study to assess the effect of carbon nanotube addition on the through-thickness electrical conductivity of CFRP laminates for aircraft applications

The present paper tests experimentally the through-thickness electrical conductivity of carbon fiber-reinforced polymer (CFRP) composites laminates for aircraft applications. Two types of samples were prepared: Type A samples with carbon nanotubes (CNTs) and Type B samples without CNTs. During the electrical experiments, electrical currents of several mA were injected through the specimens. Electrical resistance was monitored simultaneously in order to deduce the changes in the through-the-thickness electrical conductivity caused by the addition of CNTs. Improvement of electrical conduction by two orders of magnitude was achieved through the addition of 1 wt% carbon nanotubes as compared to classic CFRP without CNTs. For moisture saturated samples, the influence of moisture absorption on such measures was found to be negligible.     

Oxidative degradation of polyamide reverse osmosis membranes: Studies of molecular model compounds and selected membranes

Selected aromatic amides were used to model the chemical reactivity of aromatic polyamides found in thin‐film composite reverse osmosis (RO) membranes. Chlorination and possible amide bond cleavage of aromatic amides upon exposure to aqueous chlorine, which can lead to membrane failure, were investigated. Correlations are made of the available chlorine concentration, pH, and exposure time with chemical changes in the model compounds. From the observed reactivity trends, insights are obtained into the mechanism of RO membrane performance loss upon chlorine exposure. Two chemical pathways for degradation are shown, one at constant pH and another that is pH‐history dependent. An alternative strategy is presented for the design of chlorine‐resistant RO membranes, and an initial performance study of RO membranes incorporating this strategy is reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1173–1184, 2003     

Cu基络合物催化甲醇液相氧化羰化反应

针对甲醇液相氧化羰基化法合成碳酸二甲酯(DMC)工艺,开发了新型Cu基络合催化剂(CuB rnLm)。对CuB rnLm催化剂的活性及其稳定性进行了研究。实验结果表明,采用该催化剂,甲醇转化率和DMC选择性较高;元素价态和物质结构分析表明,CuB rnLm催化剂循环使用5次后仍保持较好的稳定性。采用正交设计和中心响应曲面法设计实验,并使用S tatistica软件进行统计分析,寻求出反应的主要影响因素,并得到优化的工艺条件:反应温度100~110℃、反应压力3.0~3.5M Pa、反应时间4~6h、CuB rnLm催化剂质量浓度(以甲醇的体积计)0.15~0.20g/mL。在此工艺条件下,甲醇转化率可达23%以上,DMC的选择性为96%~98%。     

Alumina-supported catalysts for propane oxidative dehydrogenation from mixed VXM(6−X)O19 (M=W, Mo) hexametalate precursors

γ-Al₂O₃ supported vanadium oxides were modified by tungsten and molybdenum oxides in order to improve dispersion and selectivity towards olefins in propane oxidative dehydrogenation (ODH). Both vanadium–tungsten and vanadium–molybdenum catalysts were obtained by adsorption of mixed isopolyanions (VW₅O₁₉⁵⁻, V₂W₄O₁₉⁴⁻, VMo₅O₁₉⁵⁻ and V₂Mo₄O₁₉⁴⁻) from aqueous solutions. The isopolyanion solutions were characterized by UV-Vis and ⁵¹V NMR spectroscopy. Vanadium, vanadium–tungsten and vanadium–molybdenum precursors and catalysts were also characterized by UV-Vis (diffuse reflectance) and solid state ⁵¹V NMR spectroscopy. An improved selectivity to propene in the presence of tungsten and molybdenum in VO_x/γ-Al₂O₃ was observed and attributed to dilution of vanadium by tungsten or molybdenum oxides on the γ-Al₂O₃ surface.     

Environmental factors and kinetics of microbial degradation of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) in an aqueous medium

Environmental factors such as oxygen, temperature, and microbial species may have significant effects on decomposition of biodegradable polymers. A representative biodegradable, thermoplastic polymer, poly(3‐hydroxybutyrate‐co‐hydroxyvalerate) (PHBV), was decomposed in an aqueous medium under controlled laboratory conditions by soil microbes for the intrinsic degradation kinetics and the effects of the environmental factors on polymer biodegradation. The amount of proteins, including the PHBV depolymerases, that attached to the polymer surfaces was quite constant during the period of significant mass loss of the polymer specimens. The microbial polymer degradation followed a zero‐order rate model, so the residual mass fraction of PHBV films declined linearly with time. The mixed aerobic microbial organisms from fertile soil showed a higher activity of polymer degradation than an aerobic PHBV‐producing bacterium and the mixed anaerobes in the same soil. The mixed anaerobic microorganisms from barren soil decomposed the polymer at a slower rate than the anaerobes from fertile soil, and this was attributed to fewer microbial cells in the barren soil instead of the difference in the microbial species. The temperature effect on PHBV degradation can be described with an Arrhenius equation, and the activation energy is around 16 kcal/mol. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 205–213, 2003     

Abrasion phenomena in twill tencel fabric

The abrasion characteristics of Tencel fabrics were evaluated by Martindale abrasion and laundering, and the breakdown mechanism of fibers was surveyed by scanning electron microscopy. The fabric was subjected to pad‐dry‐cure treatment with two different types of modified dimethyloldihydroxyethylene urea resins (Reaktant DH and Reaktant FC). Although the degree of dry abrasion varied with different resins, the damage exhibited by individual fibers differed little from untreated to resin‐treated; the major mechanism of abrasion was through friction, and the mechanism of fiber failure was multiple splitting and transverse cracking. In untreated Tencel, the characteristic feature of wet abrasion was massive fibrillation, and in crosslinked fabrics, the wet abrasion mechanism was through fiber slippage and slicing action, although in the Reaktant FC‐treated fabric, the wet abrasion mechanism was more through slicing than through fiber splitting. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1391–1398, 2006     

阳离子化多元醇防塌剂的研制

室内研究和现场应用表明,聚乙烯醇类防塌剂表现出较明显的增粘负效应,可引起钻井液粘度的急剧增加,严重影响其推广应用.通过金属盐催化降解和阳离子化反应,研制出了抑制性好且增粘负效应低的阳离子化改性多元醇防塌剂.考察了阳离子化试剂、反应温度、反应时间对取代度、反应效率和产品主要性能的影响,得出了阳离子化多元醇防塌剂最佳制备条件,即：PVA与阳离子化试剂物质的量比为1：1,反应温度为50℃,反应时间为4 h,阳离子度可达0.435.