汽车计算平台工程国外相关标准概述

结合我国汽车计算平台工程,分析了国外相关的标准现状和基本框架,并为今后工作的开展提出了建议.     

无机高分子絮凝剂聚硫酸铁合成条件的研究

实验研究了以工业硫酸亚铁及废硫酸为原料,分别采用NaClo_3、KClO_3、H_2O_2及(o_2+NaNO_2)为氧化剂成聚硫酸铁的条件。在以(O_2+NaNO_2)为氧化剂的合成过程中,发现添加微量助催化剂(型号为HG-1、HG-2和HG-3),对提高合成速度及反应过程的稳定性具有重大作用。     

An experience of tunnelling in mudstone area in southwestern Taiwan

Many tunnels will be constructed in southwestern Taiwan in the upcoming decade to meet the huge demands of transportation, energy and water infrastructure projects. Mudstone strata cover more than a 1000 km² area, consisting mainly of massive mudstone or alternation of mudstone and sandy layer, exhibiting unfavorable geological and hydrological characteristics, making it extremely difficult for tunnelling. This paper presents the lessons learned from three tunnelling projects in the 1990s in a mudstone area. In addition to discussing the rock behavior in the vicinity of tunnel and its failure patterns, the monitoring data during tunnelling are presented as well. Finally, the effective method of design and construction are recommended for tunnelling in mudstone area.     

鄱阳湖控制浅说

该控制工程主要效益是改变鄱阳湖“夏水冬陆”的现状，成为祖国名符其实的第一大淡水湖，水面与避署胜地庐山和历史名城南昌、景德镇等相连，改善沿湖环境，发展航运，增加水产，开发利用丰富的水资源和旅游资源使之与杭州西湖、瑞士日内瓦湖等并列为世界名湖。     

黄河黑山峡河段大柳树水库比小观音水库原始库容多40亿m3的作用

一级开发大柳树高坝原始库容比二级开发小观音高坝多 4 0亿m3 ,库容大带来的好处体现在 5～ 7月可多向下游增供水量 ,缓解下游河道断流 ;延长泄放清水时间 ;增加发电效益 ;满足宁蒙河段防凌要求 ;增加汛期集中泄水 ,减缓下游河道淤积萎缩 ;满足南水北调西线工程水量调节要求等。为了更好优化配置黄河水资源 ,从全局和长远利益考虑 ,应采用一级开发方案 ,修建大柳树高坝大库     

Study of liquid injection impact on the performance of new refrigerant mixtures

In this paper, the test results of liquid injection impact on the performance of new alternative refrigerant mixtures such as: R-410A, R-507, R-407C and R-404A are discussed, analysed and presented. The test results were obtained using an air-source heat pump set-up with enhanced surface tubing under various liquid injection ratios. Performance tests were conducted according to the ARI/ASHRAE standards. The performance data demonstrated that as liquid injection ratio increases, compressor head pressure and discharge temperature decrease. This has a positive effect in protecting the compressor. The effect of liquid injection on mixture behaviour varies from one mixture to another depending upon the mixture's composition. Furthermore, liquid injection appears to have a significant influence on R-410A behaviour compared to the other mixtures in question. Copyright © 2002 John Wiley & Sons, Ltd.     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

In Situ Performance Testing of Deteriorating Water Tanks for Durability Assessment

Reports of failure of existing concrete structures due to a lack of durability, rather than a deficiency in structural strength, has made concrete technologists, engineers, and researchers focus research on the parameters influencing durability performance with respect to time. Systematic performance monitoring, with respect to chosen durability parameters of existing concrete structures, will decide the direction of future research in this area. Inferences based on laboratory simulations and testing need to be confirmed by in situ field measurements and studies. In situ condition rating and performance monitoring surveys have been conducted by many researchers, scientists, and professional associations, and reported in literature. Inferences of few such studies are summarized and discussed. Deterioration of concrete structures constructed in recent times is observed at relatively faster rates, and has been mainly attributed to cracking. Cracking is associated with the use of faster-hydrating portland cements with increased fineness and the tricalcium silicate (C3S) content to support the high speed of modern construction. In the present research, a case study of deteriorated water tank structures situated in the semitropical region of India is presented. Some selected parameters—such as concrete cover, carbonation depth, chloride concentration, compressive strength, etc. which influence long term durability of structures—have been measured.