碳酸性侵蚀与AAR作用下纳米混凝土的耐久性

地铁混凝土处于地下空间,容易受到地下水的碳酸性侵蚀；碱集料反应 (AAR)是一种严重的混凝土耐久性问题,既难以发现又难以修补,由两者共同作用引起的混凝土耐久性降低严重影响地铁隧道的正常使用.为研究纳米材料对地铁混凝土在碳酸性侵蚀和AAR共同作用下耐久性的影响,在普通混凝土中掺入适量纳米SiO₂和纳米Fe₂O₃,利用自行研制的碳酸性侵蚀试验箱进行试验,采用碳酸性侵蚀深度、膨胀率和声速作为测试指标来评价纳米混凝土在碳酸性侵蚀和AAR共同作用下的耐久性.试验结果表明:掺入纳米颗粒后,混凝土的膨胀率和侵蚀深度有了明显降低,而声速有了明显提升,说明纳米混凝土的耐久性优于普通混凝土；在182 d龄期时,掺量为2%的纳米SiO₂混凝土耐久性改善最明显,侵蚀深度和膨胀率最小,声速最大且声速下降幅度最小；其次是掺量为1%的纳米Fe₂O₃混凝土.由于纳米颗粒特殊的物理化学性质,改善了混凝土内部的微观结构和孔溶液的化学组成,使碳酸性侵蚀和碱集料反应共同作用下混凝土的耐久性得到了提高.     

超临界蒸汽参数对燃气蒸汽联合循环性能影响研究

为进一步提高联合循环效率,参考现有燃气蒸汽联合循环12.5 MPa/568℃亚临界蒸汽参数,提出27 MPa/585℃超临界蒸汽参数,根据燃气蒸汽联合循环计算模型,以397 MW燃气轮机联合循环机组为例,计算了超临界蒸汽参数与两种亚临界蒸汽参数的底循环效率和联合循环效率,并分析对比了3种蒸汽参数的底循环效率对联合循环效率的贡献。研究表明:对于同一燃气轮机,超临界和亚临界中低压蒸汽参数不同时,超临界蒸汽参数的底循环效率比亚临界提高了4.3%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由30.21%增加到32.62%,联合循环净效率增加了2.21%,联合循环机组的输出功率增加了20.38 MW;中低压蒸汽参数相同时,超临界蒸汽参数的底循环效率比亚临界提高了2.87%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由31.16%增加到32.62%,联合循环净效率增加了1.44%,联合循环机组的输出功率增加12.5 MW。     

Combined constant speed control method for a wind generator equipped with hydraulic energy storage

A wind generator equipped with hydraulic energy storage (WG‐HES) uses hydraulic transmission systems instead of gearbox transmissions, thus eliminating high‐power converters and reducing the tower‐top cabin weight. When there is no wind or the wind speed is extremely low, the pressured oil released by accumulators is used to drive a motor to operate at a constant speed, thereby generating constant‐frequency power. However, few studies have examined the constant speed control characteristics for generating electricity using only an accumulator group. In this study, a combined constant speed (CCS) proportional–integral–derivative (PID) control method based on “variable displacement and throttling” is proposed, which includes two closed loops and one regulating loop. First, a simulation model of the CCS PID control method for a variable motor was established in the Simcenter Amesim program. The influence of different PID parameters on the anti‐interference ability of the constant speed control of the motor was analyzed under a given load step. Then, we obtained the range of control parameter values and a set of optimal values. Second, the effectiveness of the CCS control method and the accuracy of the simulation results were verified on a 600‐kW WG‐HES system prototype. The results verified that the CCS control method has good anti‐interference ability and can meet the requirements of constant speed control for a variable motor under the best PID parameters. These results can provide a basis for developing control strategies for WG‐HESs when there is no wind or at low wind speeds.     

Effects of temperature on creepage discharge characteristics in oil-impregnated pressboard insulation under combined AC–DC voltage

Due to the complexity of the valve side winding voltage of the converter transformer, the insulation characteristics of the oil-impregnated pressboard (OIP) of the converter transformer are different from those of the traditional AC transformer. The study on effect of temperature on the creeping discharge characteristics of OIP under combined AC–DC voltage is seriously inadequate. Therefore, this paper investigates the characteristics of OIP creepage discharge under combined AC–DC voltage and discusses the influence of temperature on creepage discharge characteristics under different temperatures from 70°C to 110 °C. The experimental results show that the partial discharge inception voltage and flashover voltage decrease with increasing temperature. The times of low amplitude discharge (LAD) decrease and amplitude of LAD increases. Simultaneously, the times of high amplitude discharge (HAD) gradually increase at each stage of creepage discharge with higher temperature. The analysis indicates that the charge carriers easily accumulate and quickly migrate directional movement along the electric field ahead of discharging. The residual charge carriers are more easily dissipated after discharging. The ‘hump’ region of LAD moves to the direction of higher discharge magnitude. The interval time between two continuous discharges is shortened obviously. The concentration of HAD accelerates the development of OIP insulation creepage discharge. The temperature had an accelerating effect on the development of discharge in the OIP under applying voltage.     

冶金矿物和产品水分测定问题探讨

水分测定是冶金行业中矿产原料和产品分析的重要内容,主要包括交货水分、湿存水、化合水等测定类别。尽管水分测定方法本身相对简单,但其涉及到矿物原料、产品结算交割以及其他化学分析的校正计算,属于重要的基础性测定方法。各类矿物、产品几乎都有相应水分测定的国家标准、行业标准,部分还是从国外ISO标准体系中采标而来。文章系统介绍并比较各类矿物原料、产品中交货水分、明水、湿存水、化合水等类别的测定方法。由于ISO标准体系中湿存水含义和国内标准体系湿存水含义有较大差异,其测定操作和用途也有不同,使用空气平衡样品和密封原始样品将会得到数据差异较大的湿存水数据,两种湿存水含义需要明确区分。湿存水对化学称样量、灼减量、化合水的测定有影响,需要用湿存水进行水分校正,才能得到更精确的结果。     

Does thermal control improve visual satisfaction? Interactions between occupants’ self-perceived control,visual, thermal,and overall satisfaction

Occupants’ satisfaction had been researched independently related to thermal and visual stimuli for many decades showing among others the influence of self-perceived control. Few studies revealed interactions between thermal and visual stimuli affecting occupant satisfaction. In addition, studies including interactions between thermal and visual stimuli are lacking different control scenarios. This study focused on the effects of thermal and visual factors, their interaction, seasonal influences, and the degree of self-perceived control on overall, thermal, and visual satisfaction. A repeated-measures laboratory study with 61 participants running over two years and a total of 986 participant sessions was conducted. Mixed model analyses with overall satisfaction as outcome variable revealed that thermal satisfaction and visual satisfaction are the most important predictors for overall satisfaction with the indoor environment. Self-perceived thermal control served as moderator between thermal satisfaction and overall satisfaction. Season had slight influence on overall satisfaction. Random effects explained the highest amount of variance, indicating that intra- and interindividual differences in the ratings of satisfaction are more prevalent than study condition. Future building design and operation plans aiming at a high level of occupant satisfaction should consider personal control opportunities and take into account the moderating effect of control opportunities in multimodal interactions.     

海水中134Cs、137Cs和60Co的联合分析

建立了小体积海水中¹³⁴Cs、¹³⁷Cs和⁶⁰Co的联合分析方法，确定了最佳实验条件。采用磷钼酸铵富集法对海水中放射性铯进行浓集后，其上清液利用氢氧化钴沉淀载带海水中的⁶⁰Co，用γ能谱仪进行测量。结果表明：该法对海水中放射性¹³⁴Cs、¹³⁷Cs和⁶⁰Co的回收率分别为87%~95%、87%~95%和89%~93%，检测限分别为0.048、0.051、0.046 Bq/L。另外，对2017年IAEA国际比对（IAEA-RML-2017-01）海水样品中的¹³⁴Cs、¹³⁷Cs和⁶⁰Co进行分析测量，核素分析结果的最终评价均为“通过”，验证了本实验室采用的¹³⁴Cs、¹³⁷Cs和⁶⁰Co联合分析方法的可行性和可靠性，为今后该方法在常规海洋环境放射性监测中的应用推广奠定了基础。     

钼蓝分光光度法联合测定铁矿石中磷和二氧化硅

以往铁矿石中磷和二氧化硅含量的测定需要分别采用钼蓝分光光度法。在使用磷钼蓝分光光度法时,常会因钒、砷等的干扰使得磷测定结果不准确,需要将样品再处理后才能测定。实验采用石墨垫底铁坩埚,碳酸钠和硼酸混合熔剂高温熔融铁矿石,使铁矿石样品分解彻底,再分别采用铋磷钼蓝和硅钼蓝分光光度法测定磷和二氧化硅含量,从而实现了采用钼蓝分光光度法联合测定铁矿石中磷和二氧化硅。干扰试验表明,在高温熔融时,石墨可将钒(V)还原为钒(III),使样品中钒不干扰磷的测定;显色液中加入15mg硫代硫酸钠溶液可将砷(V)还原为砷(III),继而消除砷对磷测定的干扰。磷的质量浓度在0~3μg/mL范围内遵守比尔定律,校准曲线的线性相关系数为0.9999,表观摩尔吸光系数为2.242×10⁴ L·mol^-1·cm^-1;二氧化硅的质量浓度在0~5μg/mL范围内遵守比尔定律,校准曲线的线性相关系数为0.9995,表观摩尔吸光系数为9.342×10³ L·mol^-1·cm^-1。方法中磷和二氧化硅的检出限分别为0.0026μg/mL和0.0081μg/mL。按照实验方法测定6个铁矿石标准样品中磷和二氧化硅,磷测定结果的相对标准偏差(n=8)小于5%,相对误差小于2%;二氧化硅测定结果的相对标准偏差(n=8)小于2%,相对误差小于1.5%。按照实验方法测定5个铁矿石样品中磷和二氧化硅,磷测定结果的相对标准偏差(RSD,n=8)小于7%,二氧化硅测定结果的相对标准偏差(n=8)小于1%;磷和二氧化硅的测定值均与电感耦合等离子体原子发射光谱法的测定值相一致。     

A CCD-ADI method for two-dimensional linear and nonlinear hyperbolic telegraph equations with variable coefficients

In this paper, a combined compact finite difference method (CCD) together with alternating direction implicit (ADI) scheme is developed for two-dimensional linear and nonlinear hyperbolic telegraph equations with variable coefficients. The proposed CCD-ADI method is second-order accurate in time variable and sixth-order accurate in space variable. For the linear hyperbolic equation, the CCD-ADI method is shown to be unconditionally stable by using the Von Neumann stability analysis. Numerical results for both linear and nonlinear hyperbolic equations are presented to illustrate the high accuracy of the proposed method.     

氮酮与薄荷醇联用对5-氟尿嘧啶的促透作用

目的：以5-氟尿嘧啶（5-FU）为模型药物，对氮酮和薄荷醇的促透特性进行比较，并探讨两种促透剂合用时的促透效果。方法：在离体透皮实验装置上进行透皮试验，由浓度计算累积透过量，运用倍量法对氮酮与薄荷醇联用的效果进行评价。结果： 浓度为0.25%、0.50%、1.00%、2.00%的氮酮对5-FU均有促透作用，与空白对照组相比，差异具有统计学意义（P<0.01）；浓度为0.25%、0.50%、1.00%、2.00%的薄荷醇对5-FU也有明显的促透作用，与空白对照相比，差异具有统计学意义（P<0.01）；用倍量法对两种药物联用的作用进行评价分析时，二者联用未显示有协同作用。结论：氮酮和薄荷醇对（5-FU）均有促透作用，但二者以相同浓度合用时，未有明显的协同作用。