超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

碳酸性侵蚀与AAR作用下纳米混凝土的耐久性

地铁混凝土处于地下空间,容易受到地下水的碳酸性侵蚀；碱集料反应 (AAR)是一种严重的混凝土耐久性问题,既难以发现又难以修补,由两者共同作用引起的混凝土耐久性降低严重影响地铁隧道的正常使用.为研究纳米材料对地铁混凝土在碳酸性侵蚀和AAR共同作用下耐久性的影响,在普通混凝土中掺入适量纳米SiO₂和纳米Fe₂O₃,利用自行研制的碳酸性侵蚀试验箱进行试验,采用碳酸性侵蚀深度、膨胀率和声速作为测试指标来评价纳米混凝土在碳酸性侵蚀和AAR共同作用下的耐久性.试验结果表明:掺入纳米颗粒后,混凝土的膨胀率和侵蚀深度有了明显降低,而声速有了明显提升,说明纳米混凝土的耐久性优于普通混凝土；在182 d龄期时,掺量为2%的纳米SiO₂混凝土耐久性改善最明显,侵蚀深度和膨胀率最小,声速最大且声速下降幅度最小；其次是掺量为1%的纳米Fe₂O₃混凝土.由于纳米颗粒特殊的物理化学性质,改善了混凝土内部的微观结构和孔溶液的化学组成,使碳酸性侵蚀和碱集料反应共同作用下混凝土的耐久性得到了提高.     

超临界蒸汽参数对燃气蒸汽联合循环性能影响研究

为进一步提高联合循环效率,参考现有燃气蒸汽联合循环12.5 MPa/568℃亚临界蒸汽参数,提出27 MPa/585℃超临界蒸汽参数,根据燃气蒸汽联合循环计算模型,以397 MW燃气轮机联合循环机组为例,计算了超临界蒸汽参数与两种亚临界蒸汽参数的底循环效率和联合循环效率,并分析对比了3种蒸汽参数的底循环效率对联合循环效率的贡献。研究表明:对于同一燃气轮机,超临界和亚临界中低压蒸汽参数不同时,超临界蒸汽参数的底循环效率比亚临界提高了4.3%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由30.21%增加到32.62%,联合循环净效率增加了2.21%,联合循环机组的输出功率增加了20.38 MW;中低压蒸汽参数相同时,超临界蒸汽参数的底循环效率比亚临界提高了2.87%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由31.16%增加到32.62%,联合循环净效率增加了1.44%,联合循环机组的输出功率增加12.5 MW。     

保健食品标准中重(装)量差异指标的分析及应用

近年来, 保健食品注册和备案技术指引要求保健食品制剂制订重量差异或装量差异指标, 如片剂等剂型应制订重量差异指标, 胶囊剂等剂型应制订装量差异指标, 以替代原先对包装食品通用的净含量与负偏差指标。在执行过程中, 检测机构众多检验结果显示有不少生产企业可能未能完全理解重量差异和装量差指标的具体分析算法和应用细节要求, 导致抽检结果与生产企业出厂检验结果不一致的情况。本文着重对重量差异和装量差异测定方法的质控目的、限度设定、计算与判定方法等进行详细解读, 以帮助相关企业更好地理解重量差异和装量差异的指标特性和分析应用要点, 阐明重量差异和装量差异指标与包装食品通用的净含量与负偏差指标的不同, 使规范制订保健食品标准并正确执行分析检验。     

Hybrid self-inertia weight adaptive particle swarm optimisation with local search using C4.5 decision tree classifier for feature selection problems

ABSTRACT

Feature selection is an important task to improve the classifier’s accuracy and to decrease the problem size. A number of methodologies have been presented for feature selection problems using metaheuristic algorithms. In this paper, an improved self-adaptive inertia weight particle swarm optimisation with local search and combined with C4.5 classifiers for feature selection algorithm is proposed. In this proposed algorithm, the gradient base local search with its capacity of helping to explore the feature space and an improved self-adaptive inertia weight particle swarm optimisation with its ability to converge a best global solution in the search space. Experimental results have verified that the SIW-APSO-LS performed well compared with other state of art feature selection techniques on a suit of 16 standard data sets.     

The control of paracetamol particle size and surface morphology through crystallisation in a spray dryer

The parameters governing the crystallisation of paracetamol using various conventional techniques has been extensively studied, however the factors influencing the drug crystallisation using spray drying is not as well understood. The aim of this work was to investigate the crystallisation of an active pharmaceutical ingredient through evaporative crystallisation using a spray dryer to study the physicochemical properties of the drug and to use semi-empirical equations to gain insight into the morphology and particle size of the dried powder. Paracetamol solutions were spray dried at various inlet temperatures ranging from 60 °C to 120 °C and also from a series of inlet feed solvent compositions ranging from 50/50% v/v ethanol/water to 100% ethanol and solid-state characterisation was done. The size and morphology of the dried materials were altered with a change in spray drying parameters, with an increase in inlet temperature leading to an increase in particle Sauter mean diameter (from 3.0 to 4.4 µm) and a decrease in the particle size with an increase in ethanol concentration in the feed (from 4.6 to 4.4 µm) as a result of changes in particle density and atomised droplet size. The morphology of the dried particles consisted of agglomerates of individual crystallites bound together into larger semi-spherical agglomerates with a higher tendency for particles having crystalline ridges to form at higher ethanol concentrations of the feed.     

Combined constant speed control method for a wind generator equipped with hydraulic energy storage

A wind generator equipped with hydraulic energy storage (WG‐HES) uses hydraulic transmission systems instead of gearbox transmissions, thus eliminating high‐power converters and reducing the tower‐top cabin weight. When there is no wind or the wind speed is extremely low, the pressured oil released by accumulators is used to drive a motor to operate at a constant speed, thereby generating constant‐frequency power. However, few studies have examined the constant speed control characteristics for generating electricity using only an accumulator group. In this study, a combined constant speed (CCS) proportional–integral–derivative (PID) control method based on “variable displacement and throttling” is proposed, which includes two closed loops and one regulating loop. First, a simulation model of the CCS PID control method for a variable motor was established in the Simcenter Amesim program. The influence of different PID parameters on the anti‐interference ability of the constant speed control of the motor was analyzed under a given load step. Then, we obtained the range of control parameter values and a set of optimal values. Second, the effectiveness of the CCS control method and the accuracy of the simulation results were verified on a 600‐kW WG‐HES system prototype. The results verified that the CCS control method has good anti‐interference ability and can meet the requirements of constant speed control for a variable motor under the best PID parameters. These results can provide a basis for developing control strategies for WG‐HESs when there is no wind or at low wind speeds.     

基于改进雷达图的配电系统电能质量评估方法

本文针对配电系统电能质量综合评估存在的评估指标权重分配过于主观或客观的问题,提出一种基于改进雷达图法的配电系统电能质量评估方法。该方法利用最小偏差组合权重法计算各评估指标的最优组合权重。并在传统雷达图的基础上对各指标轴间夹角值的确定和特征向量的选取两方面做了进一步的改进。首先采用扇形区域取代原始的三角形区域,并利用最小偏差组合权重法计算各指标轴间夹角值。其次选择新的特征向量构造评估函数对配电系统电能质量进行综合评估。最后通过对某钢铁厂棒材变电站10kV配电系统电能质量进行综合评估,验证了该方法的可行性和合理性。较传统雷达图而言,改进雷达图法解决了传统雷达图法中各指标间信息共用以及评估结果不唯一的问题,使评估结果更加准确合理。     

Effects of temperature on creepage discharge characteristics in oil-impregnated pressboard insulation under combined AC–DC voltage

Due to the complexity of the valve side winding voltage of the converter transformer, the insulation characteristics of the oil-impregnated pressboard (OIP) of the converter transformer are different from those of the traditional AC transformer. The study on effect of temperature on the creeping discharge characteristics of OIP under combined AC–DC voltage is seriously inadequate. Therefore, this paper investigates the characteristics of OIP creepage discharge under combined AC–DC voltage and discusses the influence of temperature on creepage discharge characteristics under different temperatures from 70°C to 110 °C. The experimental results show that the partial discharge inception voltage and flashover voltage decrease with increasing temperature. The times of low amplitude discharge (LAD) decrease and amplitude of LAD increases. Simultaneously, the times of high amplitude discharge (HAD) gradually increase at each stage of creepage discharge with higher temperature. The analysis indicates that the charge carriers easily accumulate and quickly migrate directional movement along the electric field ahead of discharging. The residual charge carriers are more easily dissipated after discharging. The ‘hump’ region of LAD moves to the direction of higher discharge magnitude. The interval time between two continuous discharges is shortened obviously. The concentration of HAD accelerates the development of OIP insulation creepage discharge. The temperature had an accelerating effect on the development of discharge in the OIP under applying voltage.