水力空化改质对重质原油沥青质及性质的影响

利用水力空化过程产生局部的高温、高压、高射流以及强大的剪切力等极端化学物理条件改质处理沙特重质原油，试验结果表明：沙特重质原油经过水力空化改质后粘度由13.61降低至7.22mm2/s，残碳由7.16%降低至6.48%，实沸点蒸馏后减压渣油降低1个百分点。进一步采用APPI FT-IR MS、XRD、FT-IR、SEM和粒度分布等技术研究了水力空化改质对沙重原油分子组成，沥青质团聚体微晶结构、沥青质胶束粒径分布、沥青质官能团、沥青质形貌等方面的影响，从分子角度阐述空化改质重油的机理。研究结果表明：水力空化改质后沙重原油分子量分布、芳烃类化合物缔合作用变小；沥青质对低DBE化合物吸附性能降低；沥青质团聚体微晶结构更加松散；沥青质胶束粒度分布降低；沥青质分子相互团聚作用力减弱。进一步考察了水力空化改质前后减压渣油延迟焦化性能，改质处理后焦炭产率降低1.85个百分点，液体收率和气体产率分别增加1.52和0.33个百分点，水力空化改质对沥青质性质、结构特点的改善能够有效的提高其加工性能。     

Sulfate- and pH-driven metabolic flexibility in sugarcane vinasse dark fermentation stimulates biohydrogen evolution,sulfidogenesis or homoacetogenesis

Dark fermentation of sugarcane vinasse can be used as a “cleaning” step to remove sulfate prior to methanogenesis because sulfidogenic conditions can be successfully established in parallel with biohydrogen production. Using a 2² central composite rotational design (CCRD) and response surface methodology (RSM), this study assessed the impacts of bicarbonate and sulfate availability on the establishment of sulfidogenesis in the thermophilic (55 °C) fermentation of vinasse in batch reactors, equally assessing the impacts on biohydrogen evolution. CCRD-RSM results indicated the favoring of biohydrogen production at the lowest sulfate and bicarbonate concentrations, whilst the opposite was observed for sulfidogenesis. Glycerol, lactate, and hydrogen were the preferential electron donors utilized by sulfate-reducing bacteria (SRB), whilst ethanol was markedly consumed only at high sulfate concentrations. SRB were inhibited by sodium when dosing excess NaHCO₃ and Na₂SO₄. Complementary tests revealed maximum biohydrogen production (2.40 mmol) out of the CCRD, at pH exceeding 7.5 with no interference of sulfidogenesis. Non-efficient biohydrogen production was observed at low pH (<5.0; ～1.90 mmol) because the uptake of lactate was inhibited. Meanwhile, homoacetogenesis was established under intermediate pH range (5.5–6.5), as revealed by the accumulation of acetate (up to 2.5 g L^?1). 16S rRNA gene amplicon sequencing further revealed the genera Thermoanaerobacterium/Pseudoclostridium, Desulfotomaculum/Desulfohalotomaculum and Sporomusaceae/Moorella as the main biohydrogen-producing, sulfate-removing and biohydrogen-consuming (homoacetogens) microbial groups, respectively. Hence, using a single inoculum source, vinasse may provide a butyrate-rich (along with biohydrogen-rich biogas) or a sulfate-free and acetate-rich fermented effluent, depending mainly on proper pH control.     

有砟轨道路基翻浆冒泥模型试验系统的研发与应用

为研究既有线有砟轨道路基的翻浆冒泥机理，自主研发了一套能够模拟循环荷载–湿化耦合作用的模型试验系统。模型试样直径500 mm，由厚度分别为350 mm的路基土和200 mm的道砟组成，整个试样在高强度透明有机玻璃模型筒中制备完成。模型试验系统配备有监测荷载、位移、体积含水率和孔隙水压力的4种传感器，并通过高清相机对颗粒迁移过程进行图像捕捉。基于所研发的试验系统，针对辛泰铁路典型翻浆冒泥病害路段土样，开展翻浆冒泥模型试验。试验结果表明：动孔隙水压力是导致翻浆冒泥病害产生的关键因素。随着体积含水率的增加，动孔隙水压力引起的颗粒迁移量逐渐增加；在饱和状态下，会引起大量颗粒迁移，翻浆冒泥现象显著。试验结束时，道砟污染指数达到25%，在实际工程中已严重影响铁路的正常运营，有必要对污染道砟进行换填。     

Tunable BaxSr1-xTiO3 nanoparticles induced high energy storage density in layer-structured asymmetric polymer-based nanocomposites

In order to solve the problem of low charging and discharging energy density of dielectric capacitors, the structure design of layered polymer matrix composites is carried out in this paper. Ba_0.7Sr_0.3TiO₃, Ba_0.8Sr_0.2TiO₃ and Ba_0.9Sr_0.1TiO₃ nanoparticles were successfully prepared by the oxalate coprecipitation method. The surface of Ba_xSr_1-xTiO₃ was successfully coated with dopamine, which promoted the dispersion of the polymer matrix of the ceramic powder. Monolayer Ba_xSr_1-xTiO₃/PVDF composites containing Ba_xSr_1-xTiO₃ with different Ba/Sr ratios were successfully prepared by the casting method. Three-layer asymmetric composites with different fillers were successfully prepared by layer-by-layer casting. The phase and microstructure of the as-prepared materials were analyzed by XRD and SEM. The dielectric, electrical conductivity, ferroelectric and energy storage properties of the composites were tested. The effects and laws of the design of the three-layer asymmetric structure on the dielectric properties and energy storage properties of the layered composites are mainly studied. When the structure of the three-layer asymmetric composite is 1-2-3, the breakdown field strength reaches 330 kV/mm, the discharge energy density reaches 8.51 J/cm³, and the charge-discharge efficiency is 67%. This work demonstrates that layered composites with asymmetric properties can facilitate the development of electrical energy storage.     

毫米波三维异质异构集成技术的进展与应用

三维异质异构集成技术是实现电子信息系统向着微型化、高效能、高整合、低功耗及低成本方向发展的最重要方法,也是决定信息化平台中微电子和微纳系统领域未来发展的一项核心高技术。文章详细介绍了毫米波频段三维异质异构集成技术的优势、近年来的发展趋势以及面临的挑战。利用硅基MEMS 光敏复合薄膜多层布线工艺可实现异质芯片的低损耗互连,同时三维集成高性能封装滤波器、高辐射效率封装天线等无源元件,还能很好地处理布线间的电磁兼容和芯片间的屏蔽问题。最后介绍了一款新型毫米波三维异质异构集成雷达及其在远距离生命体征探测方面的应用。     

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

MnS掺杂多孔碳复合材料的制备及电化学性能（两张发票1000+2500）

褐煤作为低级煤资源利用率不高，但褐煤中具有腐植酸成分，将褐煤中提取的腐植酸作为化肥原料，提取后剩余残渣作为碳源，与MnS纳米粒子制备了MnS@C复合材料。采用XRD、拉曼光谱、XPS、N2吸附-脱附、SEM和TEM对样品进行了表征。将该复合材料应用于锂离子电池负极材料，对其电化学性能进行了测试。结果表明，MnS@C复合材料的比表面积和孔容分别为117.19m2/g和0.044mL/g，该电极在0.1 A/g电流密度条件下循环200次后比容量高达830 mA‧h/g，且电极容量保持率为99%左右。在0.2、0.4、0.8、1.0、1.2和1.6 A/g电流密度下比容量分别为644、522、427、399、373和348mAh/g，展现出良好的倍率性能。MnS@C复合材料优异的电化学性能得益于碳基体的存在，不仅可以缓解MnS纳米粒子在嵌锂/脱锂过程中的体积膨胀，而且展示了锂离子电池高性能的巨大潜力，为褐煤的高值化利用作出巨大贡献。     

Catalytic combustion synthesis of CNTs/MgO composite powders and the influences on the thermal shock resistance of low-carbon Al2O3–C refractories

Using MgC₂O₄, Mg powders as raw materials and Ni(NO₃)₂?6H₂O as a catalyst, CNTs/MgO composite powders were prepared by a catalytic combustion synthesis method. The CNTs/MgO composite powders were characterized by XRD, Raman spectroscopy, FESEM/EDS and HRTEM. The effects of catalyst content on the degree of graphitization and aspect ratio of the CNTs in composite powders were investigated. Moreover, the thermal shock resistance of low-carbon Al₂O₃–C refractories after adding the composite powder was investigated. The results indicated that the CNTs prepared with 1 wt% Ni(NO₃)₂?6H₂O addition had a higher degree of graphitization and aspect ratio. In particular, the aspect ratio could reach approximately 200. The growth mechanism of hollow bamboo-like CNTs in the composite powders was proven to be a V-L-S mechanism. The thermal shock resistance of Al₂O₃–C samples could be improved significantly after adding CNTs/MgO composite powders. In particular, compared with CM0, the residual strength ratio of Al₂O₃–C samples with added 2.5 wt% composite powders could be increased 63.9%.     

Fabrication and properties of the superhydrophobic ceria-based composite coating on magnesium alloy

A superhydrophobic ceria-based composite coating is developed to improve anticorrosion properties of AZ61 magnesium alloy, fabricating via chemical conversion method followed by hydrothermal treatment. The cerium conversion coating has a block structure with microcracks. After the hydrothermal treatment, a dense CeO₂ layer, porous CeO₂ nanorods, and stearic absorbing layers are grown stepwise on the conversion coating. And the composite coating is hydrophobic or even superhydrophobic and has almost no microcracks. As the hydrothermal reaction time increases, the water contact angle of the composite coating first increases and then decreases, and it reaches the maximum value of 152° after hydrothermal treatment for 4 h. Both the dense CeO₂ layer and the superhydrophobic stearic absorbing layer can effectively prevent the electrolyte from contacting the substrate; the corrosion current density of the superhydrophobic composite coating is lower than that of the hydrophilic composite coating and the cerium conversion coating, and has the best corrosion resistance.     

Surface generation mechanism of ceramic matrix composite in ultrasonic assisted wire sawing

Ceramic matrix composites (CMC) are highly required in many fields of science and engineering. However, the CMC parts always have poor surface finish. This study attempts to improve cutting performance of CMC material by combing the advantages of ultrasonic assisted cutting and diamond wire sawing. Cutting force, surface roughness, machined edge and tool wear are analyzed based on experimental results. It shows that the oscillatory movement of tool edges provides positive effect on particle ejection and residual material reduction. Ductile chip formation can be achieved due to the small tip radius of grits. Obvious decrease in cutting force, surface roughness and tool wear are obtained. Moreover, burrs, fuzzing and fracture are reduced. Meanwhile, both the surface characteristics and shape accuracy are significantly improved. These results provide a valuable basis for application of ultrasonic assisted wire sawing and understanding of CMC cutting mechanisms.