Investigation of La0.6Sr0.4Co1-xNixO3-δ (x=0, 0.2, 0.4, 0.6, 0.8) catalysts on solid oxide fuel cells anode for biogas dry reforming

The introduction of catalyst on anode of solid oxide fuel cell (SOFC) has been an effective way to alleviate the carbon deposition when utilizing biogas as the fuel. A series of La_0.6Sr_0.4Co_1-xNi_xO_3-δ (x = 0, 0.2, 0.4, 0.6, 0.8) oxides are synthesized by sol-gel method and used as catalysts precursors for biogas dry reforming. The phase structure of La_0.6Sr_0.4Co_1-xNi_xO_3-δ oxides before and after reduction are characterized by X-ray diffraction (XRD). The texture properties, carbon deposition, CH₄ and CO₂ conversion rate of La_0.6Sr_0.4Co_1-xNi_xO_3-δ catalysts are evaluated and compared. The peak power density of 739 mW cm^?2 is obtained by a commercial SOFC with La_0.6Sr_0.4Co_0.4Ni_0.6O_3-δ catalyst at 850 °C when using a mixture of CH₄: CO₂ = 2:1 as fuel. This shows a great improvement from the cell without catalyst for internal dry reforming, which is attributed to the formation of NiCo alloy active species after reduction in H₂ atmosphere. The results indicate the benefits of inhibiting the carbon deposition on Ni-based anode through introducing the La_0.6Sr_0.4Co_0.4Ni_0.6O_3-δ catalyst precursor. Additionally, the dry reforming technology will also help to convert part of the exhaust heat into chemical energy and improve the efficiency of SOFC system with biogas fuel.     

Effect of polyethyleneimine-fatty acid complex type dispersant structure on the overall processing chain of Si3N4 ceramics using multicomponent non-aqueous slurries

The effect of fatty acid structure of polyethyleneimine (PEI)-fatty acid complex, which was designed as a polymer dispersant for multi-component non-aqueous slurries, on the overall processing chain of Si₃N₄ ceramics involving slurry stabilization, spray drying, compaction, and liquid sintering was investigated using PEI-oleic acid (PEI-OA) and PEI-isostearic (PEI-ISA) complexes. Si₃N₄-Y₂O₃-Al₂O₃-AlN-TiO₂/toluene slurries were selected as a real model for Si₃N₄-based multicomponent slurries. It was observed that both PEI-OA and PEI-ISA can stabilize Si₃N₄-Y₂O₃-Al₂O₃-AlN-TiO₂/toluene slurries; however, the PEI-ISA system tended to have slightly higher slurry viscosity, which was suspected to be due to the interactions between protruded PEI segments among short ISA chains. The spray-dried granules from PEI-ISA-stabilized slurry were observed to have filled structures with higher surface roughness whereas those prepared from PEI-OA-stabilized slurry were observed to have hollow-structured granules. The granules prepared from PEI-OA slurry had improved flow and compaction properties with higher relative density of green compacts compared with those prepared from PEI-ISA-stabilized slurry, whereas the relative density and microstructural homogeneity of S₃N₄ ceramics sintered at 1600?°C for 2?h were observed to be higher for the PEI-ISA system. It is suspected that PEI-OA effectively improved the dispersion stability of multicomponent slurries and flow/compaction properties of granules; however, the inhomogeneous microstructures of green compacts induced by the hollow-structured granules had an adverse effect on the sintering of Si₃N₄ ceramics.     

Recent advances during CH4 dry reforming for syngas production: A mini review

Given the continuing issues of environment and energy, methane dry reforming for syngas production have sparked interest among researchers, but struggled with the process immaturity owing to catalyst deactivation. This review summarizes the recent advances in the development of efficient and stable catalysts with strong resistance to coking and metal sintering, including the application of novel materials, the assessment of advanced characterizations and the compatibility to improved reaction system. One feasible option is the crystalline oxide catalysts (perovskite, pyrochlore, spinel and LDHs), which feature a fine metal dispersion and surface confinement effect via a metal exsolution strategy and exhibit superior reactivity and stability. Some new materials (h-BN, clays and MOFs) also extend the option because of their unique morphology and microstructure. It also is elaborated that progresses were achieved in advanced characterizations application, leading to success in the establishment of reaction mechanisms and attributions to the formed robust catalysts. In addition, the perspective described the upgrade of reaction system to a higher reaction efficiency and milder reaction conditions. The combination of efficient reaction systems and robust catalysts paves a way for a scaling-up application of the process.     

干熄焦锅炉炉管失效机理分析

通过对干熄焦锅炉炉管及腐蚀产物开展系统研究，提出炉管失效原因为氧化/硫腐蚀＋高温粉尘冲刷。长寿命炉管仅耐磨层发生了较为严重的氧化及硫腐蚀，而近基体层发生了轻微氧化及硫腐蚀，基体只发生了轻微氧化；短寿命炉管耐磨层、近基体层以及基体裂纹内均发生了较为严重的氧化及硫腐蚀，且存在珠光体球化、内表面产生全脱碳层等缺陷。推测短寿命炉管存在超温现象，而超温可加剧氧化及硫腐蚀反应。此外，短寿命炉管遭受了较为严重的高温粉尘冲刷，不仅可造成炉管减薄，还会导致炉管表面温度升高。因此，减少循环气体中粉尘量尤其是大颗粒，可有效减弱冲刷以及控制炉管表面温度，是提高炉管使用寿命的关键。     

Impact of pre-treatment (soaking or germination) on nutrient and anti-nutrient contents,cooking time and acceptability of cooked red dry bean (Phaseolus vulgaris L.) and chickpea (Cicer arietinum L.) grown in Ethiopia

Pulses are processed in diverse ways prior to consumption. Soaking and germination are among the most common traditional, household-level food processing strategies. This study was carried out to determine the effects of soaking, germination, cooking and their combinations on the contents of selected nutrients and anti-nutrients of red dry bean and chickpea. In addition, the effects of pre-treatment on cooking time and the acceptability of dishes prepared from red dry bean and chickpea were determined. The nutrient compositions (zinc, iron and calcium) of most soaked-cooked and germinated-cooked red dry bean and chickpea samples were not significantly different than those of respective controls. However, soaking and germination pre-treatments significantly lowered the phytate and tannin contents of the red dry bean and chickpea samples, with a few exceptions, and overall, polyphenol contents were lower after soaking-cooking than after germination-cooking. Most scores for sensory attributes of bean-based and chickpea-based dishes prepared from soaked or germinated samples were not significantly different than those of the controls. For most red dry bean and chickpea samples, longer germination times yielded superior results in terms of reductions in cooking time, tannin content, and phytate:zinc and phytate:iron molar ratio.     

Experimental investigation of different morphology textured ceramic tools by in-situ formed for the dry cutting

Surface texture is considered an important measure to improve the cutting performance of a tool. In this study, we have prepared three types of textured and conventional tools on the rake face by an in-situ formed method. During the experiment, the best parameters of three types of textured tools were selected for dry cutting AISI 1045 steel at different cutting speeds. Cutting forces, cutting temperatures, workpiece surface roughness, and tool wear were measured during the cutting process. The results showed that textured tools have significantly reduced cutting force, cutting temperature, and tool wear, and the roughness of the workpiece was improved compared with the conventional tool. The micro-pit texture tool has less stress contact region than the micro-groove width texture tool, but the micro-groove width texture tool exhibiting the best cutting performance. This investigation clearly showed that the textured tool prepared by the in-situ formed method has improved cutting performance.     

A comparative thermodynamic analysis of Kalina and organic Rankine cycles for hot dry rock: a prospect study in the Gonghe Basin

Hot dry rock is a new type of geothermal resource which has a promising application prospect in China. This paper conducted a comparative research on performance evaluation of two eligible bottoming cycles for a hot dry rock power plant in the Gonghe Basin. Based on the given heat production conditions, a Kalina cycle and three organic Rankine cycles were tested respectively with different ammonia-water mixtures of seven ammonia mass fractions and nine eco-friendly working fluids. The results show that the optimal ammonia mass fraction is 82% for the proposed bottoming Kalina cycle in view of maximum net power output. Thermodynamic analysis suggests that wet fluids should be supercritical while dry fluids should be saturated at the inlet of turbine, respectively. The maximum net power output of the organic Rankine cycle with dry fluids expanding from saturated state is higher than that of the other organic Rankine cycle combinations, and is far higher than the maximum net power output in all tested Kalina cycle cases. Under the given heat production conditions of hot dry rock resource in the Gonghe Basin, the saturated organic Rankine cycle with the dry fluid butane as working fluid generates the largest amount of net power.     

唐代中日佛教干漆造像交流研究——以鉴真东渡为例

文章以唐代中日佛教干漆造像交流为研究对象,以鉴真东渡为切入点,通过历史文献等资料整理,从历史学和社会学,艺术学,设计学的角度对鉴真东渡的历史背景、鉴真六次东渡及东渡后对日本佛教干漆造像的影响三个方面进行分析和阐述,结合日本奈良时代特定的历史环境和背景,探究唐代中日佛教干漆造像交流脉络,揭示鉴真东渡及其团队对日本佛教干漆造像的深远影响,为唐代中日佛教干漆造像交流研究提供新的研究思路。     

300MWCFB锅炉配套半干法烟气脱硫的汞排放试验研究

某300 MW循环流化床(CFB)锅炉采用炉内脱硫、SNCR、预电除尘器和烟气循环流化床半干法脱硫装置实现了超低排放。对不同工况下不同位置的烟气汞浓度和灰渣等固体副产物中的汞含量进行测试分析,研究结果表明:燃煤在循环流化床锅炉燃烧产生的汞主要以气态汞和颗粒汞形式存在;锅炉负荷提高,烟气中气态汞和颗粒汞浓度均有所提高,炉内脱硫对原始汞排放特性几乎没有影响;烟气循环流化床半干法脱硫装置可脱除71%～77%的气态汞和86%～88%的颗粒汞;采用预电除尘器与烟气循环流化床半干法脱硫结合的超低排放路线,总汞脱除率可达到82%～87%,使烟囱排放的汞浓度不高于1.5μg/m~3。副产物分析结果表明,烟气中脱除的汞主要富集于粉煤灰和半干法脱硫灰中。