The effect of ionic cross-links on the deformation behavior of homoblends made of poly(styrene-co-styrenesulfonic acid) and poly(styrene-co-4-vinylpyridine)

Deformation behavior of stoichiometric blends made from poly(styrene-co-styrenesulfonic acid) (SPS) and poly(styrene-co-4-vinylpyridine) (SVP) was investigated by TEM observation of strained thin films. An FTIR investigation revealed that ionic cross-links were formed between the component polymers upon blending due to intermolecular ion-ion interactions, which arose from proton transfer from sulfonic acid groups to pyridine groups. TEM observations indicate that the deformation mode of the blends changed from crazing only to crazing plus shear deformation, with the shear contribution becoming larger, as the ion content in the blends increased. Such changes in deformation mode can be understood as arising from an increase in the ‘effective’ strand density due to the formation of ionic cross-links upon blending. It was also found that the ionic cross-links via pyridinium cation/sulfonate anion ion pairs were more effective in inducing the transition of deformation mode than ionic cross-links via -SO₃⁻/Na⁺ or -SO₃⁻/Ca²⁺ ion pairs.     

裂解炉炉管基于风险的检验

管式裂解炉炉管受炉内高温及管内介质压力的共同作用,易发生蠕变等现象,因此,对裂解炉炉管进行风险评价尤为重要。应用API 581基于风险的检验规范对炉管的失效可能性及失效后果分别进行定量计算,并由此得到裂解炉炉管的定量风险结果和基于风险的检验周期,为裂解炉的风险控制与管理提供依据。     

细节决定采输卤的成败

通过认真学习《细节决定成败》，结合井矿盐开采的实际，分别以生产过程中的三个细节为主，讨论了在采输卤生产技术控制中的细节的重要性。     

WC/Cu复合材料制备及其高温性能

用机械合金化法结合冷变形，制备了WC／Cu复合材料，研究了冷变形后复合材料的组织特征和高温退火时韵性能变化。结果表明：烧结后的材料经冷变形，组织呈显著纤维状，WC颗粒弥散分布，密度明显提高，达到理论密度的99．2％；复合材料经600～900℃高温退火，强度和硬度略有下降，塑性则有大幅提高；900℃退火时未发生明显的再结晶，界面结合良好；所制备的WC／Cu复合材料有优良的综合性能。     

可控震源施工中电台数据传输不良的原因分析及排除

可控震源在施工中,常常出现各种电台干扰,导致震源数据传输不正常或震源收不到仪器发出的遥控启动信号,影响正常施工.本文介绍了各种电台干扰引起的故障现象,分析了故障产生的原因,给出了故障的排除方法.     

Failure analysis of a broken tooth

Several days after heart surgery, a patient discovered his upper right canine tooth had broken at the root. Such tooth damage, recognized post-operatively, is usually assumed to be caused by blunt mechanical force from an instrument used by the anesthesiologist during placement of a breathing tube at the start of surgery. In this case, the patient had saved the crown portion of the broken tooth, and it was possible to examine the root fracture characteristics. The curvature and direction of the crack path and natural tooth situation suggested that failure could be described through a cantilever beam model. This was confirmed when a whole extracted sample tooth was embedded and broken by a measured force in a manner consistent with the model. The resulting fracture surface matched that of the patient’s broken canine tooth. However, the high load and force direction necessary to fracture the root was inconsistent with forces applied during the anesthesia procedure. The failure analysis and further investigation indicated tooth clenching on the breathing tube during recovery was the likely cause of fracture. This paper presents an alternate explanation for intubation-related dental injury, demonstrates the practicality of fractographic analysis of biological materials, and introduces a methodology for simulating in vitro tooth settings for mechanical testing.     

多孔板体结构足尺性能分析及材料基本要求

本文就利用诸如蛋白石这样的疏松多孔矿料同灰土构成的混合料，在路面结构中表现出的独特有效的抗冻作用机理作了深入分析，并结合足尺试验数据加以验证。阐述了所谓多孔板体结构的概念、机制和材料组成要求。     

具有细小组织的高强度和高延性钢管的开发

介绍了日本川崎制铁公司技术研究所开发出的电焊钢管采用热张力减径工艺的特性 ,及这种钢管的高强度、高延性等基本特性。用这种钢管制造的汽车零部件 ,经弯曲、冲击和疲劳特性等实验 ,证明具有良好的机械加工性能 ,是制造汽车用零部件的优良材料。     

换热器小浮头螺栓断裂失效分析

针对换热器小浮头螺栓发生断裂的情况进行失效分析，找出原因，提出处理措施及材质选择时应注意的问题。     

广州地铁一号线隧道结构变形监测及成果分析

介绍了广州地铁一号线运营以来的全线隧道结构变形监测 ,分析了隧道结构的安全状况和各种变化规律 ,并对其变形原因进行有益的探讨