Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.     

浅谈DC/DC变换器控制新方法

文中针对DC/DC变换器的特点,在现有控制和建模方法的基础之上,对DC/DC变换器的现代控制方法进行了归纳和总结,简要讨论了其控制原理,并比较了各种现代控制方法的优缺点,最后对DC/DC变换器控制方法的发展作了一定的展望。     

伶仃洋三维潮流输沙的数值模拟

作者使用垂向坐标变换技术，结合有限差分方法建立了三维潮流输沙的数学模型。为了增加模型的稳定性和减少数值耗散，对悬沙对流扩散方程中的水平对流项采用三阶迎风格式离散。应用本模型对伶仃洋的枯季和洪季的潮流输沙的悬沙场进行了数值模拟，将模拟结果与实测资料进行比较，二者吻合较好。模拟结果分析表明：伶仃洋悬沙运动主要集中在西滩，对伶仃航道影响不大；洪季水体含沙浓度高于枯季；水体含沙浓度沿水深存在浓度梯度，且洪季的浓度梯度明显大于枯季。     

欠平衡钻井过程中的井控新设备

文章简述了欠平衡钻井中不压井操作的设备和方法,介绍了威得福公司的井下套管阀和海底泥浆举升钻井工业联合项目在深水钻井中研发的新钻杆阀在欠平衡钻井中的应用。通过在钻杆上安装钻杆阀和在套管上安装套管阀解决接单根及起下钻操作时因压井可能破坏欠平衡状态的问题,使全过程的欠平衡钻井得以实现。     

转炉溅渣护炉改质剂的开发研究

影响转炉溅渣护炉效果的关键因素是终渣成分的控制,采用改质剂对转炉终渣成分进行调整,降低渣中FeO含量和炉渣温度,提高MgO含量和炉渣熔点及粘度,有利于改善炉渣与炉衬的粘结效果,并提高溅渣层的耐蚀性能,缩短溅渣起孕时间,在一定程度上抑制炉渣中铁的氧化物与炉衬中石墨的反应.     

AD2S80在测角系统中的应用

DS2S80是美国AD公司生产的以鉴幅方式对感应同步器信号进行处理的专用芯片。由它与感应同步器构成的测角系统具有成本低、功耗小、所需外部元件少、可靠性好等优点。介绍了AD2S80数字转换芯片的引脚、组成测角系统的工作原理、外围电路的设计，给出了一种半量式测角系统的实现方案。     

济钢转炉煤气储存加压系统存在缺陷及处理措施

济钢燃气厂针对济钢转炉煤气储存加压系统的设备现状，组织了一次设备大修，大修后煤气柜升降速度提高到了1．0m/min，并解决了加压机前负压等问题。     

电潜泵中压变频调速系统的改进

电潜泵中压变频器输出端产生高次谐波和脉冲电流 ,对电潜泵电动机的绝缘性能和轴承寿命造成不利影响。为此 ,提出 3项改进对策 :①采用谐振软性开关逆变电路 ,使功率开关器件在零电压条件下导通 ;②在变频器逆变输出端设置电抗滤波器抑制高次谐波电流 ;③改变电动机内部结构 ,如加大定子槽宽 ,增加转子导条尺寸 ,变星接法为星 角接法 ,采用绝缘轴承等。实践证明 ,采取改进对策后 ,不仅提高了电潜泵的产量 ,而且变频器滤波后电动机端的过电压明显减小 ,电潜泵和电缆的寿命延长     

A versatile data acquisition system for time resolved X-ray scattering using gas proportional detectors with delay line readout

A data acquisition system for time resolved X-ray scattering experiments using linear, quadrant or area gas proportional detectors with delay line readout based on commercially available hardware (National Instruments) is described. The system can easily be configured for recording data from point detectors (e.g. photomultipliers and photodiodes) and/or ancillary data only. Applications involving measurements with two different types of time to digital converters illustrate the features and performances of the system.     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.