Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

Friction compensation controller for load varying machine tool feed drive

The load applied to a machine tool feed drive changes during the machining process as material is removed. This load change alters the Coulomb friction of the feed drive. Because Coulomb friction accounts for a large part of the total friction the friction compensation control accuracy of the feed drives is limited if this nonlinear change in the applied load is not considered. This paper presents a new friction compensation method that estimates the machine tool load in real time and considers its effect on friction characteristics. A friction observer based on a Kalman filter with load estimation is proposed for friction compensation control considering the applied load change. A specially designed feed drive testbed that enables the applied load to be modified easily was constructed for experimental verification. Control performance and friction estimation accuracy are demonstrated experimentally using the testbed.     

对CFG桩质量缺陷的探讨

根据具体工程的概况及水文地质条件，分析了CFG桩在地下水位出现大面积缩颈现象和复合地基载荷试验达不到设计要求的原因，并介绍了地基补强措施，以满足工程质量的要求。     

Improving Short-Circuit Current Capacity, Resistance, and Breaking Load of OPGW Constructions by Modifying Aluminium Alloy With AlB2

This article presents a method that can be applied to molten AA-6101 alloy to improve electrical properties of the aluminium part of the optical ground wire (OPGW) used in overhead transmission lines to protect phase conductors from lightning strike and to transmit signals and data. AA-6101 alloy in casting of the log as 6 m length and 178 mm diameter for extrusion has been inoculated by AlB₂ to decrease detrimental effects of Cr, Ti, V, and Zr on the conductivity of the material. After inoculation, improved billets were extruded as 9.5 mm diameter feedstock. Required wires drawn from the feedstock according to the construction types of OPGW to be tested were exposed to aging at 175°C, 6 h (T-8). Upon completion of the back-twist and performing-type stranding process, resistance, and short-circuit current capacity and breaking load of the OPGW 88/44 constructions with other metal combinations have been examined and tested to show improvement. Results are summarized in tables and graphically.     

伶仃洋三维潮流输沙的数值模拟

作者使用垂向坐标变换技术，结合有限差分方法建立了三维潮流输沙的数学模型。为了增加模型的稳定性和减少数值耗散，对悬沙对流扩散方程中的水平对流项采用三阶迎风格式离散。应用本模型对伶仃洋的枯季和洪季的潮流输沙的悬沙场进行了数值模拟，将模拟结果与实测资料进行比较，二者吻合较好。模拟结果分析表明：伶仃洋悬沙运动主要集中在西滩，对伶仃航道影响不大；洪季水体含沙浓度高于枯季；水体含沙浓度沿水深存在浓度梯度，且洪季的浓度梯度明显大于枯季。     

在广西全面开展悬移质泥沙简测的可行性和重要性

通过对百色等水文站泥沙资料分析 ,并结合广西河流及泥沙特性和社会对泥沙资料的精度要求 ,得出了在广西实行悬移质泥沙简测的可行性。为满足广西国民经济可持续发展需要 ,提出了在广西改革悬移质泥沙测验方式的必要性和紧迫性     

压型钢板组合楼板承载力的有限元分析

压型钢板组合楼板是 2 0世纪发展起来的一种新型结构形式。它具有显著的优势 ,如轻质、高强 ,施工快捷等 ,将在未来的建筑领域中大有作为。组合楼板的承载力主要取决于钢板 -混凝土界面处的抗剪强度。建立了一个二维有限元模型来研究单向组合板的性能。并将计算结果与试验数据进行对比 ,验证了模型的有效性     

Microscopic and Macroscopic Growth Rates of Fatigue Cracks in Steels and Alloys under the Influence of Crack Closure

On the basis of the experimental data, we show that the difference between the macroscopic and microscopic fatigue crack growth rates in the second section of the kinetic diagram of fatigue fracture is caused by the effect of crack closure within the limits of its existence. We establish the relationships between the macroscopic and microscopic fatigue crack growth rates and the structure of the material in the second section of the diagram for various values of the load ratio with regard for the effect of crack closure and propose a procedure of examination of the fracture processes in structural materials based on the analysis of microscopic and macroscopic fatigue crack growth rates.     

新型复合弹簧的研究

提出一种金属圆锥弹簧与橡胶圆锥弹簧复合而成的弹簧．分析表明：它可以应用于弹性耦合激励振动筛和座式直线振动筛。     

Performance analysis of IEEE 802.11 ad hoc networks in the presence of exposed terminals

The paper evaluates the performance effects of exposed terminals in IEEE 802.11 ad hoc networks in finite load conditions. It derives analytical models for the estimation of channel utilization and media access delay for IEEE 802.11 ad hoc networks in finite load conditions with and without exposed terminals. The simulation results show that the analytical estimated channel utilization and media access delay metrics are fairly accurate.