An optimal configuration for hybrid SOFC,gas turbine,and Proton Exchange Membrane Electrolyzer using a developed Aquila Optimizer

In this research, a technical, economic and environmental analysis has been proposed to a Hybrid Solid Oxide Fuel Cell (SOFC) system-based hybrid system including biomass, gas turbine, and Proton Exchange Membrane Electrolyzer. A multi-objective optimization technique has been utilized to improve the overall product cost and the exergy effectiveness based on a developed version of Aquila Optimizer (DAO). The main idea of using the developed version is to improve the accuracy and the precision of the original Aquila optimizer. The system is then authenticated in terms of energy/exergy effectiveness, and energy-economic efficiency. The achievements indicate that employing the optimization algorithm for different configurations provided satisfying results for the system.     

内含实体对H型垂直轴风力机气动性能的影响

以H型垂直轴风力机及其内含圆柱形实体为研究对象,对NACA0018翼型的五叶片H型垂直轴风力机的气动性能进行数值模拟和实验验证。分析8种不同直径的内含圆柱体,在内含实体截面积占风轮迎风面积之比分别为21.2%、50.0%和76.9%时,风力机风能利用率的峰值分别下降8.04%、20.7%及74.3%。结果表明：随着内含实体直径的增大,风能利用率的峰值逐渐减小,开始较为缓慢,达到一定值时快速下降。小直径内含实体主要影响叶片在下风区的转矩,对风能利用率的影响较小,而大直径内含实体还会影响叶片在上风区的转矩,其风能利用率迅速减小。对于内含固定直径的实体,比如在现有建筑物外侧安装风力机时,其风轮半径的选择需综合考虑风能利用率和风力机的建造成本两方面的因素。研究结果可为建筑物与垂直轴风力机进行有效结合以提高风能的利用提供参考。     

An economic investigation of the wind-hydrogen projects: A case study

Hydrogen as an energy carrier can play a significant role in reducing environmental emissions if it is produced from renewable energy resources. This research aims to assess hydrogen production from wind energy considering environmental, economic, and technical aspect for the East Azerbaijan province of Iran. The economic assessment is performed by calculation of payback period, levelized cost of hydrogen, and levelized cost of electricity. Since uncertainty in the power output of wind turbines may affect the payback period, all calculations are performed for four different turbine degradation rates. While it is common in the literature to choose the wind turbine based on a single criterion, this study implements Multi-Criteria Decision-Making (MCDM) techniques for this purpose. The results of Step-wise Weight Assessment Ratio Analysis illustrates that economic issue is the most important criterion for this research. The results of Weighted Aggregated Sum Product Assessment shows that Vestas V52 is the most suitable wind turbine for Ahar and Sarab cities, while Eovent EVA120 H-Darrieus is a better choice for other stations. The most suitable location for wind power generation is found to be Ahar, where it is estimated to annually generate 2914.8 kWh of electricity at the price of 0.045 $/kWh, and 47.2 tons of hydrogen at the price of 1.38 $/kg, which result in 583 tons of CO₂ emission reduction.     

Thermodynamic performance analysis and environmental impact assessment of an integrated system for hydrogen and ammonia generation

A novel multigeneration plant that's using natural gas for power, hydrogen, ammonia, and hot water generation, is planned and analyzed, in the current paper. The suggested combined plant integrated with four sub-systems, which are the Brayton cycle, reheat Rankine cycle, the high-temperature steam electrolyzer for hydrogen production, and ammonia synthesis processes. Also, thermodynamic analysis and environmental impact assessment are conducted for the designed plant and sub-systems. Moreover, the sustainability index analysis of this proposed study is conducted. The effects of some important indicators on the performance and on the environmental impact of the modeled system and sub-processes are also studied. According to analyses results, it is noted that the energetic and exergetic efficiencies of the suggested system are 51.83% and 70.27%, respectively, and also the total CO₂ emission rate is 11.4 kg/kWh for the integrated plant. Furthermore, the total irreversibility rate is computed as 40007.68 kW, and furthermore, the combustion chamber has a maximum irreversibility rate with 20,033 kW, among the proposed plant components.     

潮流能水平轴水轮机在剪切来流下的水动力分析

采用基于计算流体力学方法的全尺度数值模拟计算,建立了适用于潮流能水轮机模拟的剪切来流环境,通过数值计算结果,对潮流能水轮机随时间变化的宏观力和流场特征进行了系统分析,探索水轮机在复杂工况下的水动力特性规律。结果表明,水轮机整个叶轮的总体平均受力在剪切流工况中未受到明显影响; 单个叶片的瞬态轴向力系数和瞬态轴向扭矩系数在旋转周期内出现了明显的周期性变化,且周期性变化幅值随转速增大而增大; 非定常的瞬时轴向扭矩和力的周期性振荡容易引起单个叶片的结构性振动,可能对水轮机的机械结构造成影响。     

A simple model for deep dynamic stall conditions

The present study is focused on modeling of dynamic stall behavior of a pitching airfoil. The deep stall regime is in particular considered. A model is proposed, which has a low implementation and computational complexity but yet is able to deal with different types of dynamic stall conditions, including those characterized by multiple vortex shedding at the airfoil leading edge. The proposed model is appraised against an extensive data set of experimental (α,C_L) curves for NACA0012. The results of an existing widely used model, having comparable complexity, are also shown for comparison. The proposed model is able to well reproduce not only the classic curves of deep dynamic stall but also the curves characterized by lift oscillations at high angles of attack due to the shedding of multiple vortices. Furthermore, the model appears to be robust to variations of its parameters from the optimal values and of the airfoil geometry. Finally, the model is successfully implemented in a commercial CFD software and applied to the simulation of a vertical axis wind turbine within the actuator cylinder approach. The accuracy of the prediction of the turbine power coefficient in the whole rotation cycle is very good for the optimal working condition of the turbine, for which the model parameters were calibrated. Fairly good accuracy is also obtained in significantly different working conditions without any further calibration.     

Multiple surrogate based optimization of a bidirectional impulse turbine for wave energy conversion

Oscillating water column based wave energy extracting system has a low efficiency due to the poor performance of its principal power extracting component, the bidirectional turbine. In the present work, flow over a bidirectional impulse turbine was simulated using CFD technique and optimized using multiple surrogates approach. The surrogates being problem dependent may produce unreliable results, if a wrong surrogate is selected. Hence, multiple surrogates such as response surface approximation, radial basis function, Kriging and weighted average surrogates were incorporated in this problem. Same design points were used to generate multiple optima via multiple surrogates to enhance the robustness of the optimization process. Numbers of guide vanes and rotor blades were chosen as the design variables, and the objective was to maximize the blade efficiency. Reynolds-averaged Navier–Stokes equations were solved for analyzing the flow physics. The computed results were used to train the surrogates and find the optimal points via hybrid genetic algorithm. The surrogates were further applied to find the optimal flow parameters by changing flow velocity and turbine speed. The relative efficiency enhancement through our present approach was about 16%. Detailed methodologies, analysis of the results and surrogate applicability have been presented in this paper.     

Development of low-noise drag-type vertical wind turbines

In this study, the aerodynamic noise characteristics of Savonius wind turbines were investigated using hybrid computational aero-acoustics techniques, and low-noise designs were proposed based on the understanding of the noise generation mechanism. First, the flow field around the turbine was analyzed in detail by solving three-dimensional unsteady incompressible Reynolds-averaged Navier–Stokes equations using computational fluid dynamics techniques. Then, the aerodynamic noise radiating from the wind turbine was predicted using the Ffowcs Williams and Hawkings equation with the obtained flow field information. Two distinct harmonic noise components—the blade passing frequency (BPF) and harmonics with a fundamental frequency that is much higher than the BPF—were identified in the predicted noise spectrum. The origin of the higher harmonic components was found to be related to vortex shedding from the rotating turbine. Based on this finding, the proposed low-noise design for Savonius wind turbines uses S-shaped blades. S-shaped blades were found to reduce the noise levels of Savonius wind turbines by up to 2.7 dB.     

Multilevel approach to lifetime assessment of steam turbines

This paper presents a multilevel methodology for a steam turbine lifetime assessment based on the damage calculation, probabilistic analysis and fracture mechanics considerations. Creep-fatigue damage calculations serve as a basis for evaluating the current lifetime expenditure and for defining additional steps of analysis. The need for the use of probabilistic analysis results from the inherent uncertainty in estimating the lifetime expenditure primarily caused by scatter in material properties. Fracture mechanics considerations are helpful in determining additional safety margins for components containing cracks. This methodology has been illustrated using an example of the lifetime calculations of a high-temperature steam turbine rotor. The calculations were based on the results of 2D numerical simulations performed for steady state and transient operating conditions.     

汽轮机运行调节方式优化策略探析

分析了汽轮机的喷嘴调节、节流调节、旁通调节、定压调节和滑压调节等几种基本调节方式的特点,指出现役燃煤火电机组多因调节方式单一而普遍存在着调峰能力不足、负荷响应迟缓以及因长期偏离设计工况致使运行安全经济性下降等诸多问题,提出了通过调节方式的优化组合,采用(节流)定压-滑压-(喷嘴)定压-旁通调节的复合调节方式,以实现煤电机组安全、经济、灵活、快速地参与电网的深度调峰,破解具有强随机波动性的新能源电量规模化并网的困境。