Friction compensation controller for load varying machine tool feed drive

The load applied to a machine tool feed drive changes during the machining process as material is removed. This load change alters the Coulomb friction of the feed drive. Because Coulomb friction accounts for a large part of the total friction the friction compensation control accuracy of the feed drives is limited if this nonlinear change in the applied load is not considered. This paper presents a new friction compensation method that estimates the machine tool load in real time and considers its effect on friction characteristics. A friction observer based on a Kalman filter with load estimation is proposed for friction compensation control considering the applied load change. A specially designed feed drive testbed that enables the applied load to be modified easily was constructed for experimental verification. Control performance and friction estimation accuracy are demonstrated experimentally using the testbed.     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Influence of Polyalkylmethacrylate VII on Boundary Film Formation,Friction,Wear and Efficiency of Lubricants

1 Influence of PAMAon Boundary Fil mFormation and Friction1.1 Experi mental methodsUltra-thin optical interferometry has been used tostudy thinlubricating fil ms for more than a decade and theexperi mental details of this technique have been reportedpreviously[1].The principle of the test setup is shown inFigure1.A polished steel ball is loaded and rolled againstthe flat surface of a glass disc that is coated with a thinsemi-reflecting chromiumlayer and a silica spacer of about500nmthickne…     

非稳定井流模型的半解析解

为了提高非稳定渗流计算的计算精度 ,通过数学分析得到了水位传导系数随时间变化时 ,一类非稳定渗流井流模型的半解析解 ,并进行了计算比较     

Mechanical spectroscopy in commercial Fe–6 wt.% Si alloys between 400 and 1000 K

Mechanical spectroscopy, neutron diffraction and differential scanning calorimetry (DSC) were performed on commercial Fe–6 wt.% Si alloy after quenching from high temperature. The damping spectrum shows a peak at around 800 K and an associated modulus defect. The modulus shows an increase during the second and subsequent heating runs. In addition, an anomaly in the modulus behavior has been found at around 400 K. Different thermal treatments allows to obtain two different recovery degrees of the quenched-in defects. The influence of the recovery degree on the 800 K internal friction peak and on the anelastic modulus has been evaluated and confirm the validity of the grain boundary mechanism associated to this peak. Experimental results are discussed on the basis of recovery and ordering processes.     

MB8镁合金薄板的搅拌摩擦焊

针对我国航空航天工业常用的MB8镁合金。采用搅拌摩擦焊工艺进行焊接，对其焊缝的成形特点、组织特征和力学性能进行分析。结果表明，采用搅拌摩擦焊焊接镁合金效果良好。     

Acoustic emission method for research and control of friction pairs

One of the new physical methods that provides much information about the processes going on in a friction contact zone in real time is acoustic emission (AE). Basic experimental results of AE in friction are presented and analysed. Using AE signals we can get an indication about the state of the friction processes, about the quality of solid and liquid layers on the contacting surfaces in real time, sometimes about intensity of wear, changing of wear and friction regimes and so on. The influence of sliding velocity, load, roughness and some physical and mechanical properties of the body on the parameters of AE are also given. Some attention to the practical implementation of these techniques for control of capability for work of friction pairs in real conditions are given. Modern methods and devices enable condition monitoring of sliding and rolling bearings.     

摩擦焊在钢制实心抽油杆修复中的应用

通过对焊接工艺及焊后热处理工艺优化，采用摩擦焊接技术对报废抽油杆中仍有使用寿命的杆头与杆体进行了拼接，获得了性能达标的抽油杆。从而提高了旧杆的修复率．降低了采油成本。该技术可在抽油杆修复及相关行业进行推广应用。     

磨损自补偿添加剂在成品油中的摩擦学效应

利用四球试验机考察了二聚酸－3－氯－2－羟基丙单酯（DAE）在4种成品油中的摩擦学性能。试验结果表明，DAE添加剂在L－HM68液压油和L－DAB100空压机油中具有良好的适应性，使其承载能力增强，摩擦系数降低及耐磨性增强；DAE在L－CKE涡轮蜗杆油中使耐磨性增强；DAE在L－CKC150齿轮油中虽使承载能力提高，减磨性增强，但有使耐磨性减小的趋势，说明DAE在不同的油中有不同的性能。     

短模型上的明渠非恒定流试验

水工整体模型试验中,明渠非恒定流至今大多被简化为恒定流,而效果有时并不理想。本文指出,只要设置固定式曲线尾门,并有必要的动态量测设备,便可模拟原型非恒定流;即使模型偏短,也能得出比恒定流试验更接近原型的成果。在同一模型上,既做恒定流试验,又进行必要的非恒定流试验,二者相辅相成,必将有助于试验水平的提高。作为例证,本文介绍了泄洪调度导致航道水面波动的一项试验成果,并以岩基冲刷、通航水流条件、围堰过水、河床冲淤等研究课题为例,讨论了采用“短模型非恒定流试验方式”的必要性与可行性。