Thermal desorption and pyrolysis direct analysis in real time mass spectrometry of Nafion membrane

Perfluorosulfonic acid ionomer membranes have been widely used as proton conducting membranes in various electrochemical processes such as polymer electrolyte fuel cells and water electrolysis. While their thermal stability has been studied by thermogravimetry and analysis of low molecular weight products, their decomposition mechanism is little understood. In this study a newly developed methodology of thermal desorption and pyrolysis in combination with direct analysis in real time mass spectrometry is applied for Nafion membrane. An ambient ionization source and a high-resolution time-of-flight mass spectrometer enabled unambiguous assignment of gaseous products. Thermal decomposition is initiated by side chain detachment above 350°C, which leaves carbonyls on the main chain at the locations of the side chains. Perfluoroalkanes are released above 400°C by main chain scission and their further decomposition products dominate above 500 °C. DFT calculation of reaction energies and barrier heights of model compounds support proposed decomposition reactions.     

An ultrasonic study on ternary xPbO–(45-x)CuO–55B2O3 glasses

A series of xPbO–(45-x)CuO–55B₂O₃ glasses (5 ≤ x ≥ 40 mol %) were prepared by the melt-quenching technique. The X-ray diffraction (XRD) patterns of the prepared glasses are found to have amorphous structure. An extensive ultrasonic study has been made to explore the structural role of PbO and CuO in the borate network. Various elastic properties were calculated from the measured data of density and ultrasonic velocity. Ultrasonic velocity and elastic moduli revealed broad humps at about 20 mol % PbO, which are attributed to the borate anomaly. Below 20 mol % PbO, all Pb²⁺ ions are considered to be entering the borate network as a glass modifier. This results in the transforms the borate network from an open structure to a denser three-dimensional structure due to BO₃ → BO₄ conversion. Beyond 20 mol, addition of PbO results in the formation of metaborate, pyroborate, and orthoborate units with NBOs. This weakness the glass structure and decrease both ultrasonic velocity and elastic moduli. The elastic properties were predicted and quantitatively analyzed by taking into account the effect of boron coordination number on the compositional and structural parameters involved in Makishima–Mackenzie's theory, ring deformation model and bond compression model. An excellent agreement between the computed theoretical and experimental elastic moduli, micro-harness and Poisson's ratio was achieved for majority of samples.     

Chemical bond characteristics and infrared reflectivity spectrum of a novel microwave dielectric ceramic CaIn2O4 with near-zero τf

Orthorhombic-structured CaIn₂O₄ ceramics with a space group Pca2₁ were synthesized via a solid-state reaction method. A high relative density (95.6 %) and excellent microwave dielectric properties (ε_r ～11.28, Qf = 74,200 GHz, τ_f ～ ?4.6 ppm/°C) were obtained when the ceramics were sintered at 1375 °C for 6 h. The dielectric properties were investigated on the basis of the Phillips–Van Vechten–Levine chemical bond theory. Results indicated that the dielectric properties were mainly determined by the InO bonds in the CaIn₂O₄ ceramics. These bonds contributed more (74.65 %) to the dielectric constant than the CaO bonds (25.35 %). Furthermore, the intrinsic dielectric properties of the CaIn₂O₄ ceramics were investigated via infrared reflectivity spectroscopy. The extrapolated microwave dielectric properties were ε_r ～10.12 and Qf = 112,200 GHz. Results indicated that ion polarization is the main contributor to the dielectric constant in microwave frequency ranges.     

Magnetically Guidable Proteinaceous Adhesive Microbots for Targeted Locoregional Therapeutics Delivery in the Highly Dynamic Environment of the Esophagus

The esophagus is a tubular-shaped muscular organ where swallowed fluids and muscular contractions constitute a highly dynamic environment. The turbulent, coordinated processes that occur through the oropharyngeal conduit can often compromise targeted administration of therapeutic drugs to a lesion, significantly reducing therapeutic efficacy. Here, magnetically guidable drug vehicles capable of strongly adhering to target sites using a bioengineered mussel adhesive protein (MAP) to achieve localized delivery of therapeutic drugs against the hydrodynamic physiological conditions are proposed. A suite of highly uniform microparticles embedded with iron oxide (IO) nanoparticles (MAP@IO MPs) is microfluidically fabricated using the genipin-mediated covalent cross-linking of bioengineered MAP. The MAP@IO MPs are successfully targeted to a specific region and prolongedly retained in the tubular-structured passageway. In particular, orally administered MAP@IO MPs are effectively captured in the esophagus in vivo in a magnetically guidable manner. Moreover, doxorubicin (DOX)-loaded MAP@IO MPs exhibit a sustainable DOX release profile, effective anticancer therapeutic activity, and excellent biocompatibility. Thus, the magnetically guidable locomotion and robust underwater adhesive properties of the proteinaceous soft microbots can provide an intelligent modular approach for targeted locoregional therapeutics delivery to a specific lesion site in dynamic fluid-associated tubular organs such as the esophagus.     

某微细粒嵌布磁铁矿选矿工艺研究

针对某微细粒磁铁矿进行了全磁选流程和磁选-反浮选流程对比试验研究。结果表明,在最终磨矿细度相当的情况下,2种工艺流程都获得了产率48%左右、TFe品位66%左右、回收率80%左右的铁精矿指标,而采用磁选-反浮选流程的第三段磨矿量比全磁选流程减少了2/3。磁选-反浮选流程具有显著的节能降耗优势。     

Scaling analysis of hydrogen flow with carbon dioxide cushion gas in subsurface heterogeneous porous media

Subsurface hydrogen (H₂) storage in geological formations is of growing interest for decarbonization. However, there is a knowledge gap in understanding the multiphase flow involved in this process, which can have a significant impact on the recovery performance of H₂. Therefore, a full-compositional modeling study was conducted to analyze potential issues and to understand the fundamental hydrodynamic mechanisms of H₂ storage. We performed a range of 2D vertical simulations at the decametre scale with a very fine cell size (0.1 m) to observe the detailed flow behaviour of H₂ with carbon dioxide (CO₂) as cushion gas in various flow regimes. Issues such as viscous instability, capillary bypassing, gas trapping and gravity segregation are analysed here. To generalize our calculations, we have validated and applied the scaling theory in the context of subsurface H₂ storage. Since this study is focused on the hydrodynamic behaviour, three dimensionless groups, including aspect factor, capillary/viscous ratio and gravity/viscous ratio were identified to correlate recovery performance between various scales in a fixed heterogeneous system. It was found that H₂ could infiltrate the cushion gas in the proximity of the injectors, meaning that CO₂ is not displaced away from the injectors in a piston-like fashion. As a result, the purity of the back produced H₂ is much degraded, particularly in a viscous-dominated scenario. On the other hand, the injected H₂ mostly accumulates at the top forming a highly restricted mixing zone with CO₂ in the gravity-dominated case. The recovery performance is therefore much improved in this case. Although the gas distribution can be significantly altered by capillary forces leading to bypassed zones, the recovery performance of H₂ is hardly influenced. This is because the back-produced H₂ recovery is not dependent on the sweep efficiency of the gas. H₂ can be back produced following the same paths which were formed during injection.     

自重湿陷性黄土地基预钻孔浸水处理的可靠度设计方法

为解决传统预浸水法存在的浸水时间长、浸水处理范围难以确定等不足,基于土体中水分运移规律,依据可靠度理论、极限状态设计方法及复合 Poisson 过程原理,提出一种消除黄土湿陷性的处理浸水方法——预钻孔浸水法。给出了利用预钻孔浸水法对自重湿陷性黄土地基进行浸水时,水平向及竖直向浸水影响范围的确定模型;在此基础上结合达西定律给出了浸水孔设计参数如孔深、孔间距及浸水孔个数的确定方法。结合铜川某工程,设计进行了现场预钻孔浸水试验,对该方法的合理性进行了验证,并通过现场钻探、现场勘探、室内湿陷性试验等方法对该方法的处理效果进行了评价。该浸水方法具有浸水时间短、浸水影响范围可根据浸水孔布设进行控制等优点,且浸水处理效果良好,完全符合施工要求。     

Initial and residual trapping of hydrogen and nitrogen in Fontainebleau sandstone using nuclear magnetic resonance core flooding

Hydrogen is among a few promising energy carriers of the future mainly due to its zero-emission combustion nature. It also plays an important role in the transition from fossil fuel to renewable. Hydrogen technology is relatively immature and serious knowledge gaps do exist in its production, transport, storage, and utilization. Although the economical generation of hydrogen to the scale required for such transition is still the biggest technical and environmental challenge, unlocking the large-scale but safe storage is similarly important. It is difficult to store hydrogen in solid and liquid states and storing it in the gaseous phase requires a huge volume which is just available in subsurface porous media. Sandstone is the most abundant and favourable medium for such storage as carbonate rock might not be suitable due to potential geochemical reactions.It is well established in the literature that interaction of the host rock-fluid and injected gas plays a crucial role in fluid flow, residual trapping, withdrawal, and more generally storing capacity. Such data for the hydrogen system is extremely rare and are generally limited to contact angle measurements, while being not representative of the reality of rock-brine-hydrogen interaction(s). Therefore, we have conducted, for the first time, a series of core flooding experiments using Nuclear Magnetic Resonance (NMR) to monitor hydrogen (H₂) and Nitrogen (N₂) gas saturations during the drainage and imbibition stages under pressure and temperature that represent shallow reservoirs. To avoid any geochemical reaction during the test, we selected a clean sandstone core plug of 99.8% quartz (Fontainebleau with a gas porosity of 9.7% and a permeability of 190 mD).Results show significantly low initial and residual H₂ saturations in comparison with N₂, regardless of whether the injection flow rate or capillary number were the same or not. For instance, when the same injection flow rate was used, H₂ saturation during primary drainage was 4% and it was <2% after imbibition. On other hand, N₂ saturation during the primary drainage was 26% and it was 17% after imbibition. However, when the same capillary number of H₂ was utilised for the N₂ experiment, the N₂ saturation values were ～15% for initial gas saturation and 8% for residual gas saturation. Our results promisingly support the idea of hydrogen underground storage; however, we should emphasise that more sandstone rocks of different clay mineralogy should be investigated before reaching a conclusive outcome.     

Swapping catalytic active sites from cationic Ni to anionic F in Fe–F–Ni3S2 enables more efficient alkaline oxygen evolution reaction and urea oxidation reaction

Electrolysis of water for producing hydrogen instead of traditional fossil fuels is one of the most promising methods to alleviate environmental pollution and energy crisis. In this work, Fe and F ion co-doped Ni₃S₂ nanoarrays grown on Ni foam substrate were prepared by typical hydrothermal and sulfuration processes for the first time. Density functional theory (DFT) calculation demonstrate that the adsorption energy of the material to water is greatly enhanced due to the doping of F and Fe, which is conducive to the formation of intermediate species and the improvement of electrochemical performance of the electrode. The adsorption energy of anions (F and S) and cations (Fe and Ni) to water in each material was also calculated, and the results showed that F ion showed the most optimal adsorption energy of water, which proved that the doping of F and Fe was beneficial to improve the electrochemical performance of the electrode. It is worth noting that the surface of Fe–F–Ni₃S₂ material will undergo reconstruction during the process of water oxidation reaction and urea oxidation reaction, and amorphous oxides or hydroxides in situ would be formed on the surface of electrode, which are the real active species.     

Yttrium doped covalent triazine frameworks as promising reversible hydrogen storage material: DFT investigations

Through Density Functional Theory (DFT) simulations, we have explored the possibility of yttrium (Y) doped Triazine (Covalent Triazine Frameworks i.e., CTF-1) to be a promising material for reversible hydrogen storage. We have found that Y atom strongly bonded on Triazine surface can adsorb at the most 7H₂ molecules with an average binding energy of ?0.33 eV/H₂. This boosts the storage capacity of the system to 7.3 wt% which is well above the minimum requirement of 6.5 wt% for efficient storage of hydrogen as stipulated by the US Department of Energy (DoE). The structural integrity over and above the desorption temperature (420 K) has been entrenched through Molecular Dynamics simulations and the investigation of metal-metal clustering has been corroborated through diffusion energy barrier computation. The mechanism of interactions between Y and Triazine as well as between H₂ molecules and Y doped Triazine has been explored via analyses of the partial density of states, charge density, and Bader charge. It has been perceived that the interplay of H₂ molecules with Y on Triazine is Kubas-type of interaction. The above-mentioned analysis and outcomes make us highly optimistic that Y doped Triazine could be employed as reversible hydrogen storage material which can act as an environmentally friendly alternate fuel for transport applications.