高面板坝全寿命周期变形控制方法及应用

高面板坝的变形对面板的安全运行有着特别重要的影响，国内外已建的高面板坝工程中，因坝体变形大导致防渗面板挤压破损，坝体渗漏量大的实例较多，不得不降低水库水位进行修复处理，造成较大的经济损失乃至给大坝的长期运行留下安全隐患。通过发生挤压破损的实例分析，发现变形控制缺乏系统性是发生面板挤压破损的主要因素，为预防面板破损，系统提出了“控制坝体总变形，转化有害变形，适应纵向变形”的坝体变形控制方法，并在使用软硬岩混合料筑坝的董箐面板堆石坝中得到的应用，取得了良好效果，该工程运行至今达十余年，未见面板有挤压破损迹象，该方法对建设200 m以上乃至300 m级超高面板坝具有重要借鉴意义。     

高效液相色谱法测定化妆品中依克多因的含量

建立高效液相色谱法测定化妆品中依克多因的分析方法,采用Agilent Poroshell 120 EC-C₁₈色谱柱（100 mm×3.0 mm,2.7μm）分离,以甲醇和p H为3.0的40 mmol/L磷酸二氢钠-10 mmol/L 1-庚烷磺酸钠缓冲溶液梯度洗脱,流速0.8 m L/min,柱温30℃,检测波长210 nm。采用外标法定量测定化妆品中的依克多因含量。结果表明,依克多因在5～800 mg/L的质量浓度范围内呈现良好线性关系,相关系数为0.999 8,方法的检出限和定量限分别为0.3和1.0 mg/L。该方法具有分离效率高、分析时间短、节省溶剂等优点,解决了依克多因在C₁₈色谱柱上保留弱的问题。     

Proton exchange membrane from the blend of poly(vinylidene fluoride) and functional copolymer: Preparation,proton conductivity,methanol permeability,and stability

A polymer electrolyte membrane is considered as the heart of fuel cells. Here we report the preparation of proton exchange membranes (PEMs) of poly (vinylidene fluoride) (PVDF) blend poly (methyl methacrylate)-co-poly (sodium-4-styrene sulfonate) (PMMA-co-PSSNa) by solvent evaporation method. Three different types of PEMs have been prepared by using different ratios of PVDF and PMMA-co-PSSNa copolymer. We have investigated the effect of concentration of PVDF on water uptake, ion exchange capacity, mechanical, thermal, and oxidative stability, proton conductivity (K^m), and methanol permeability (P_M) of the blend membranes. These blend PEMs showed good physicochemical and electrochemical properties along with thermal and oxidative stability. The membrane prepared from PVDF (45% w/w) to PMMA-co-PSSNa (55% w/w) exhibited optimum P_M at room temperature (8.38 × 10^?7 cm²s^?1). This low fuel crossover and high relative selectivity can make our prepared blend membranes a potential candidate in polymer electrolyte membrane fuel cells (PEMFCs) or direct methanol fuel cells (DMFCs).     

毫米波三维异质异构集成技术的进展与应用

三维异质异构集成技术是实现电子信息系统向着微型化、高效能、高整合、低功耗及低成本方向发展的最重要方法,也是决定信息化平台中微电子和微纳系统领域未来发展的一项核心高技术。文章详细介绍了毫米波频段三维异质异构集成技术的优势、近年来的发展趋势以及面临的挑战。利用硅基MEMS 光敏复合薄膜多层布线工艺可实现异质芯片的低损耗互连,同时三维集成高性能封装滤波器、高辐射效率封装天线等无源元件,还能很好地处理布线间的电磁兼容和芯片间的屏蔽问题。最后介绍了一款新型毫米波三维异质异构集成雷达及其在远距离生命体征探测方面的应用。     

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

Fabrication of high-efficiency Yb:Y2O3 laser ceramics without photodarkening

High-efficiency Yb:Y₂O₃ laser ceramics were fabricated using the vacuum-sintering plus hot isostatic pressing (HIP) without sintering additives. High-purity well-dispersed nanocrystalline Yb:Y₂O₃ powder was synthesized using a modified co-precipitation method in-house. The green bodies were first vacuum sintered at a temperature as low as 1430°C and then HIPed at 1450°C. Finally, the samples were air annealed at 800°C for 10 h. Although no sintering aids were used, full density of the samples with excellent optical homogeneity and an inline transmission of 80% at 400 nm could be obtained. Moreover, photodarkening phenomenon was not detected in the ceramics. Preliminary laser experiment with the fabricated ceramics in a two-mirror cavity has demonstrated 32 W continuous-wave (CW) output at ∼1077 nm with an optical-to-optical conversion efficiency of 58.2%. To the best of our knowledge, this is so far the highest CW output power and optical-to-optical conversion efficiency achieved with the Yb³⁺-doped sesquioxide ceramics in a simple two-mirror cavity.     

Ammonia gas sensing and magnetic permeability of enhanced surface area and high porosity lanthanum substituted Co–Zn nano ferrites

This work reports magnetic permeability and ammonia gas sensing characteristics of La³⁺ substituted Co–Zn nano ferrites possessing chemical formula Co_0.7Zn_0.3La_xFe_2-2xO₄ (x = 0–0.1) synthesized by a sol-gel route. Refinement of X-ray diffraction (XRD) patterns of the ferrite powders by the Rietveld technique has revealed the creation of single-phase spinel structure. The tenancy of constituent cations at tetrahedral/octahedral sites was obtained from the refinement of XRD. The crystallite sizes calculated from the W–H method vary from 20 to 24 nm. The scanning electron microscope (SEM) profiles of the ferrite samples were analyzed for the morphological details. The energy dispersive X-ray analysis (EDAX) patterns of the samples were obtained to test the elemental purity of the ferrites within their stoichiometry. The transmission electron microscope (TEM) image of the ferrite (x = 0.1) exhibits the spherical and oval shaped particles with a mean size of 20 nm. Fourier transform infra-red (FTIR) spectra were analyzed to confirm the superseding of La³⁺ cations at octahedral sites. The Brunauer-Emmett-Teller (BET) analysis of nitrogen adsorption-desorption isotherms of the ferrites was performed to investigate the porous structure and to determine the surface area of the nanocrystalline ferrites. The oxidation states of the constituent ions were confirmed by means of X-ray photoelectron spectroscopy (XPS). The complex permeability as a function of frequency was studied to explore the effects of structural parameters on the magnetic behaviour of the ferrites. Analysis of gas sensing properties of the ferrites have proved that the Co–Zn–La ferrite with controlled La composition can be utilized as an effective ammonia gas sensing material in commercial gas sensors.     

Omega-6支撑身体，Omega-3支撑大脑：均衡摄入对儿童大脑发育的影响（网络首发、推荐阅读）

人体大脑和身体的发育，需要从食物中摄取均衡的营养物质。人类大脑是区分人类和其他动物的特征。食物中的必需脂肪酸是机体组织结构和功能的必要组成部分。Omega-6（O6）亚油酸（LA6）是皮肤组织的组成成分，且是炎症、血栓形成、免疫和其他信号分子的前体；Omega-3（O3）α-亚麻酸（ALA3），特别是其长链代谢产物——二十二碳六烯酸（DHA3），是大脑、视网膜和部分神经组织中的关键组分。从富含LA6脂肪酸（缺乏O3脂肪酸）的植物籽中提取出的廉价而优质油脂，是20世纪的西方国家食品工业生产的主要脂肪来源。在代谢通路中，高浓度的LA6脂肪酸可拮抗O3脂肪酸代谢，造成O3脂肪酸不足，因此，在给怀孕动物的饲料中，只提供富含LA6但缺乏O3脂肪酸的油脂作为唯一的脂肪来源，会导致幼崽大脑发育不良。过去20~30年的研究表明，低含量LA6且含DHA3的油脂可改善大脑的功能。近年来的研究较多集中在营养因素对大脑发育的影响，最新研究数据表明，脂肪酸平衡对营养不良儿童的大脑发育尤为重要。世界卫生组织（WHO）越来越重视大脑的营养健康，通过其下属的食品法典委员会，建议用于治疗严重急性营养不良儿童的即食治疗食品中，使用含有均衡脂肪酸组成/构成的脂肪。同样，脂肪酸均衡对老年人可能也很重要。目前，业界已经有了调整油脂成分的方法，以确保脂肪酸均衡，从而维持人体整个生命周期的大脑健康。     

超高效液相色谱⁃四极杆⁃飞行时间质谱对含PET食品接触材料中可迁移非挥发性物质的筛查研究

采用超高效液相色谱⁃四极杆⁃飞行时间高分辨质谱（UPLC⁃Q⁃TOF）对4类不同类型的含聚对苯二甲酸乙二醇酯（PET）材质的食品接触材料在4 %乙酸和50 %乙醇模拟物中的迁移出的非挥发性未知物进行筛查解析。结果表明，产品在4 %乙酸模拟物的迁移风险远小于50 %乙醇模拟物，主要迁移物质为聚合单体形成的寡聚物，抗氧剂、润滑剂、胶黏剂等加工助剂以及生产加工、迁移过程中形成的非有意添加物（NIAS）物质；纯PET材质的产品迁移物质较少，多层复合材料迁移物质较多。复合材质的产品中，PET材质可能在生产时添加了己二酸、癸二酸、新戊二醇等物质，进行了改性处理；此外，部分迁移物质会与模拟物中的乙醇发生反应，生成新的NIAS物质。     

Microstructural and mechanical properties assessment of transient liquid phase bonding of CoCuFeMnNi high entropy alloy

The transient liquid phase (TLP) bonding of CoCuFeMnNi high entropy alloy (HEA) was studied. The TLP bonding was performed using AWS BNi-2 interlayer at 1050 °C with the TLP bonding time of 20, 60, 180 and 240 min. The effect of bonding time on the joint microstructure was characterized by SEM and EDS. Microstructural results confirmed that complete isothermal solidification occurred approximately at 240 min of bonding time. For samples bonded at 20, 60 and 180 min, athermal solidification zone was formed in the bonding area which included Cr-rich boride and Mn₃Si intermetallic compound. For all samples, the γ solid solution was formed in the isothermal solidification zone of the bonding zone. To evaluate the effect of TLP bonding time on mechanical properties of joints, the shear strength and micro-hardness of joints were measured. The results indicated a decrement of micro-hardness in the bonding zone and an increment of micro-hardness in the adjacent zone of joints. The minimum and maximum values of shear strength were 100 and 180 MPa for joints with the bonding time of 20 and 240 min, respectively.