非常规气藏储层改造体积评价方法研究

为精确描述非常规气藏压裂后的复杂流动特征及定量评价储层改造体积（SRV），利用自主研发的缝网重构算法“破裂树生长法”建立压后缝网模型，并以此为基础提出了使用拟稳态流动时特定的压力等值线来确定SRV范围的定量评价方法，最后以长宁201井区为例进行了矿场实例分析。该方法根据微地震监测点的位置，重构出微裂缝网的连通关系。在复杂微裂缝网的基础上建立离散裂缝地质模型并进行生产数值模拟，根据数值模拟结果的压力分布精确划定SRV的范围。利用该方法计算出长宁201井区的SRV体积为0.052 1 km3，以该缝网模型的数值模拟产量预测结果符合实际生产规律，方法实用性较好。     

关于多功能液压支架拖运车的电控系统设计

本文简介多功能液压支架拖运车的电控系统,包括电控箱的设计和主要电气元件的性能和选择依据。此电控系统能够一般电控系统的各种功能和保护,而且能够通过摄像头做到操作盲区和使用遥控器进行远程控制,从而提高液压支架的拖运效率、降低劳动强度和提高安全保障。     

煤峪口矿81010工作面煤层底板裂隙发育特征及防治

针对煤炭开采过程中出现的突水事故,采用RFPA数值模拟软件建立采动模型,对底板裂隙破断过程和声发射进行模拟,研究煤层底板采动裂隙扩展突水通道,结果表明:离断层越近,断层内水压导升高度越高,断层出现活化,裂隙扩展发育,最终贯通形成导水通道,在进行注浆改造后,单个钻孔的最大涌水量为8 m³/h,说明注浆加固防治水效果较好,能确保工作面的安全回采。     

Evidence of fluid evolution of Baoshan Cu−Pb−Zn polymetallic deposit: Constraints from in-situ sulfur isotope and trace element compositions of pyrite

In-situ LA-ICP-MS and S isotopes of pyrite from the Baoshan Cu polymetallic deposit were conducted to investigate the ore-forming process and the enrichment mechanism of elements. Three generations of pyrite (Py I, Py II, and Py III) in the skarn-type ores and pyrite in the carbonate-hosted sulfide ores from central, western, and northern (C_Py, W_Py, and N_Py) mining districts are selected for comparison. Compared with Py I and Py III, the contents of most elements in Py II are apparently higher. The As and Se contents are high within a wide range and are decoupled in the growth band of the C_Py. The highest As, Se, and Pb contents were found in W_Py and N_Py. These results indicate the drastic changes in the temperature and fluid mixing during the mineralization. The occurrence of fluctuation and change in temperature and f(O₂) was triggered by intermittent pulses of magmatic-hydrothermal fluids, mixing with meteoric water, and water−rock interactions. The sulfur isotopes of all species of pyrite indicated the magmatic source. The change in the f(O₂) conditions caused slight differences in the sulfur isotope compositions. Consequently, a metallogenic model was proposed to explain the ore-forming processes.     

Dense and core-rim structured B4C-TiB2 ceramics with Mo-Co-WC additive

B₄C-TiB₂ ceramics (TiB₂ ranging 5~70 vol%) with Mo-Co-WC as the sintering additive were prepared by spark plasma sintering. In comparison with B₄C-TiB₂ without additive, the enhanced densification was evident in the sintered specimen with Mo-Co-WC additive. Core-rim structured grain was observed around TiB₂ grains. The interface of the rim between TiB₂ and B₄C phases demonstrated different feature: the inner borderline of the rim exhibited a smooth feature, whereas a sharp curved grain boundary was observed between the rim and the B₄C grain. The formation mechanism is discussed: the epitaxial growth of (Ti,Mo,W)B₂ rim around the TiB₂ core may occur as a result of the solid solution and dissolution-precipitation between TiB₂ phase and the sintering additive. It was revealed that the fracture toughness increased as the content of TiB₂ content increased, alongside the decreased hardness. B₄C-30 vol% TiB₂ specimen demonstrated the optimal combination of mechanical properties, reaching Vickers hardness of 24.3 GPa and fracture toughness of 3.33 MPa·m^1/2.     

Hydraulic reactivity and cement formation of baghdadite

In this study, the hydraulic reactivity and cement formation of baghdadite (Ca₃ZrSi₂O₉) was investigated. The material was synthesized by sintering a mixture of CaCO₃, SiO₂, and ZrO₂ and then mechanically activated using a planetary mill. This leads to a decrease in particle and crystallite size and a partial amorphization of baghdadite as shown by X-ray powder diffraction (XRD) and laser diffraction measurements. Baghdadite cements were formed by the addition of water at a powder to liquid ratio of 2.0 g/ml. Maximum compressive strengths were found to be ~2 MPa after 3-day setting for a 24-h ground material. Inductively coupled plasma mass spectrometry (ICP-MS) measurements showed an incongruent dissolution profile of set cements with a preferred dissolution of calcium and only marginal release of zirconium ions. Cement formation occurs under alkaline conditions, whereas the unground raw powder leads to a pH of 11.9 during setting, while prolonged grinding increased pH values to approximately 12.3.     

超高压水力割缝技术在低渗透特厚煤层中的应用

为增大煤层透气性系数，提高煤层瓦斯抽采效果，通过超高压水力割缝技术，增大煤体暴露面积，给煤层内部卸压、瓦斯释放和流动创造了良好的条件，缝槽上下的煤体在一定范围内得到较充分的卸压，增大了煤层的透气性。结果表明:水力割缝钻孔组瓦斯抽采浓度、纯流量、百米瓦斯抽采纯流量及瓦斯抽采率是对比钻孔的2~4倍，远远大于对比钻孔组，割缝钻孔瓦斯抽采效果显著。研究为其他类似矿井提供借鉴。     

极限工况下的管网“互联互通”改进方案

在全国天然气管道“主干互联、区域成网”(以下简称“互联互通”)基础格局逐渐形成的背景下,天然气管网规模日益扩大、管道分支和气源增加,并且分布不集中、输送方向可变,使得输气方案更加灵活,可以更好地解决某些地域的供气紧张问题;但受现有站场和设备的限制,暂不能满足某些多线组合极限工况,使得“互联互通”的初衷难以全部实现。为了使得现有的各输气干线在实现“互联互通”之后可以满足更多的多线组合工况,在分析“互联互通”背景下M管网工况变化的基础上,研发了可以进行水力仿真和压气站方案制订的计算软件,并对3种极限工况下的不同输气量情况进行了可行性试算,进而基于试算结果提出了相应的管网改进建议。研究结果表明:(1)经验证,软件计算误差满足要求;(2)在M管道某处增设压气站或在某些输气站场配置压缩机组;(3) M管网改进调整后,可以完成大部分的多线组合极限工况,真正实现“互联互通”的输气方案。结论认为,该研究成果有助于推进全国天然气管网早日实现“互联互通”。     

放顶煤液压支架在土耳其IMABT煤矿现场的应用

通过对土耳其IMBAT煤矿地质条件的分析研究，结合多种选型计算方法的验证，最终选择了合适的设备，使该矿的开采效率得到较大提升。同时也扩大了我国的煤炭开采装备应用范围。根据在土耳其IMBAT煤矿现场多年的服务经验，将理论与实践相结合，就综采放顶煤液压支架在土耳其IMABT煤矿现场的应用进行了论述。     

丙烯酸装置循环气压缩机叶片损伤分析与修复

某石化公司丙烯酸装置循环气压缩机在运行过程中,一级叶片突然发生断裂,导致机组停机。采用宏观检查、扫描电子显微镜、能谱分析等方法对断裂叶片进行检验和检测,将断裂叶片的材质、裂纹及断口特征检测结果与疲劳断裂特征和机组运行状况进行对比,确定压缩机叶片的断裂系其达到疲劳寿命所致,提出采用激光熔覆方法对压缩机叶片进行修复,介绍了修复工艺操作程序要点,可为同类故事的处理提供参考。