Effect of Fe2+ and Fe0 Applied Photo‐Fenton Processes on Sludge Disintegration

The disintegration of waste active sludge was investigated by photo‐Fenton processes. A batch study was conducted to evaluate parameters, such as Fe²⁺ and Fe⁰ ions and H₂O₂, governing the activated sludge integration by the photo‐Fenton process. Under optimum conditions, the concentration of soluble chemical oxygen demand (SCOD) with the classical Fenton process (CFP) increased very rapidly in the first five minutes due to the sufficient presence of reaction components in the medium, and then the rate of increase declined. In the modified Fenton process (FTP), the SCOD concentration increased more slowly as metallic iron powder must first be dissolved. The photo‐Fenton process proved to be a feasible and efficient process for the disintegration of waste sludge.     

Application of artificial neural network method to predict the breakage properties of PGE bearing chromite ore

In the present investigation, systematic grinding experiments were conducted in a laboratory ball mill to determine the breakage properties of low-grade PGE bearing chromite ore. The population balance modeling technique was used to study the breakage parameters such as primary breakage distribution (B_{i, j}) and the specific rates of breakage (S_i). The breakage and selection function values were determined for six feed sizes. The results stated that the breakage follows the first-order grinding kinetics for all the feed sizes. It was observed that the coarser feed sizes exhibit higher selection function values than the finer feed size. Further, an artificial neural network was used to predict breakage characteristics of low-grade PGE bearing chromite ore. The predicted results obtained from the neural network modeling were close to the experimental results with a correlation of determination R² = 0.99 for both product size and selection function.     

0Cr17Ni4Cu4Nb传感器断裂原因分析

某力学传感器在出厂检验流程中发生断裂失效,为了确定失效原因,防止此类失效事件再次发生,实验对该传感器的力学性能、金相组织和断口形貌进行了分析,确定了断裂原因。结果表明,传感器的失效模式为氢致延迟开裂,材料中氢含量偏高和开裂位置机加工质量较差是导致传感器发生氢致开裂的主要原因。结合失效原因,提出了改进措施。     

A novel differential evolution mapping technique for generic combinatorial optimization problems

Differential evolution is primarily designed and used to solve continuous optimization problems. Therefore, it has not been widely considered as applicable for real-world problems that are characterized by permutation-based combinatorial domains. Many algorithms for solving discrete problems using differential evolution have been proposed, some of which have achieved promising results. However, to enhance their performance, they require improvements in many aspects, such as their convergence speeds, computational times and capabilities to solve large discrete problems. In this paper, we present a new mapping method that may be used with differential evolution to solve combinatorial optimization problems. This paper focuses specifically on the mapping component and its effect on the performance of differential evolution. Our method maps continuous variables to discrete ones, while at the same time, it directs the discrete solutions produced towards optimality, by using the best solution in each generation as a guide. To judge its performance, its solutions for instances of well-known discrete problems, namely: 0/1 knapsack, traveling salesman and traveling thief problems, are compared with those obtained by 8 other state-of-the-art mapping techniques. To do this, all mapping techniques are used with the same differential evolution settings. The results demonstrated that our technique significantly outperforms the other mapping methods in terms of the average error from the best-known solution for the traveling salesman problems, and achieves promising results for both the 0/1 knapsack and the traveling thief problems.     

风速时间序列混沌判定方法比较研究

混沌识别是对非线性时间序列进行混沌预测的前提。针对时间序列风速确定性与随机性相结合的复杂非线性特征,研究了不同的混沌识别方法,并对风速时间序列进行混沌特征识别。应用随机噪声、周期运动及经典混沌系统的时间序列对所选方法进行可靠性验证。对美国国家风能研究中心M2测风塔实测时间序列风速数据进行非线性混沌特征识别。结果表明:风速时间序列具有明显的混沌特征;各风速时间序列表现出不同程度的混沌特征;各混沌识别方法对风速时间序列混沌特征的表达形式不同,互为补充,相互验证。     

退火温度对0Cr25Al5热轧态盘条钢组织及性能的影响

采用显微组织分析和分子动力学模拟等方法研究了退火温度对0Cr25Al5热轧态盘条钢组织及性能的影响。结果发现,晶粒尺寸随温度的升高逐渐增加并趋于稳定,但是断后伸长率和断面收缩率在950 ℃突然大幅度下降。试样组织形貌在800 ℃和950 ℃退火温度下的OM及SEM分析结果未见明显差别。于是使用分子动力学模拟对0Cr25Al5钢三元体系的自由能进行了计算,发现随着B2结构的FeAl或者DO3结构的Fe₃Al有序相尺寸的增大,系统自由能先减小后增大,其最小值随着退火温度的升高向有序相颗粒尺寸减小的方向移动。在1273 K的高温下仍然会保留60 nm左右大小的有序相颗粒。因此,推测0Cr25Al5钢在大于950 ℃的温度范围内韧性下降是由于60 nm左右的B2结构的FeAl或者DO3结构的Fe₃Al有序相造成,与晶粒尺寸无关。因此,针对该钢种应进行低温退火促使基体组织回复以消除缺陷,从而抑制Fe、Al等基体原子的扩散。