Improving through-thickness conductivity of carbon fiber reinforced polymer using carbon nanotube/polyethylenimine at the interlaminar region

The through-thickness conductivity of carbon fiber reinforced polymer (CFRP) composite was increased by incorporating multiwalled carbon nanotubes in the interlaminar region. Carbon nanotubes (CNTs) were dispersed in a polyethylenimine (PEI) binder, which was then coated onto the carbon fiber fabric. Standard vacuum-assisted resin infusion process was applied to fabricate the composite laminates. This modification technique aims to enhance the electrical conductivity in through-thickness direction for the purpose of nondestructive testing, damage detection, and electromagnetic interference shielding. CNT concentrations ranging from 0 to 0.75 wt% were used and compared to pristine CFRP samples (reference). The through-thickness conductivity of the CFRP exhibited an improvement of up to 781% by adopting this technique. However, the dispersion of CNT in PEI led to a viscosity increase and poor wetting properties which resulted in the formation of voids/defects, poor adhesion (as shown in scanning electron micrographs) and the deterioration of the mechanical properties as manifested by interlaminar shear strength and dynamic mechanical analysis measurements.     

Interfacial interactions and properties of cellular structured polyurethane nanocomposite based on carbonaceous nano-fillers

In this article, we have studied the effect of carbonaceous nanofillers viz. fullerenol (0D), carboxylated multi-wall carbon nanotube (MWCNT, 1D), hydroxylated graphene (2D) and combination of carboxylated CNT and hydroxylated graphene as 3D in thermoplastic polyurethane on the tensile properties of the fabricated cellular structures. The concentration of nano-fillers was varied as 0.1, 1, and 5 wt%. Tensile properties of the nanocomposite cellular structures were measured as per ASTM D882 at 20°C (below glass transition temperature, T_g) and 40°C (above T_g). The results have shown that the tensile strength was found to increase by 200%–300% and the tensile modulus was found to increase by 150%–300% for 2D and 3D nano-fillers while significantly poor results were observed for 0D. However, the test data tensile strength and modulus showed marginal increase at 20°C and marginally low at 40°C for 1D filler. The interfacial adhesion was calculated by using experimental tensile data and the predictive models. The interfacial adhesion parameter (B_σ) calculated using Pukanszky equation was found significantly higher value for 2D (B_σ20 = 195.8) and 3D (B_σ20 = 192.0) fillers while poor adhesion was observed for 0D (B_σ20 = −81.6) fillers. The developed cellular structured materials were also evaluated by attenuated total reflection Fourier transform IR spectra, differential scanning calorimetry, X-ray diffraction, scanning electron microscope, and transmission electron microscope.     

Competitive growth of Al2O3/YAG/ZrO2 eutectic ceramics during directional solidification: Effect of interfacial energy

The microstructure evolution and growth behavior of the Al₂O₃/Y₃Al₅O₁₂(YAG)/ZrO₂ ternary eutectic ceramics during directional solidification were well investigated. During directional solidification of the Al₂O₃/YAG/ZrO₂ ternary eutectic ceramics, {} Al₂O₃ paralleled with {001}ZrO₂ while they did not parallel with {001}YAG at the same time in the competitive growth stage. All of the interfaces parallel to each other finally. The area percentage of the Al₂O₃/ZrO₂ and YAG/ZrO₂ interfaces are 40.4 ± 0.2% and 30.8 ± 0.1%, respectively, higher than that of the Al₂O₃/YAG (28.8 ± 0.2%). The content of Al₂O₃ and YAG phases are 39.9% and 41.1%, respectively, almost double of that of ZrO₂. The interfaces of Al₂O₃/ZrO₂ and YAG/ZrO₂ are shorter and more dispersed than that of the Al₂O₃/YAG. It was found that the interfacial energy of Al₂O₃/ZrO₂ and YAG/ZrO₂ interfaces are lower than that of Al₂O₃/YAG. It can be concluded that interfacial energy plays a decisive role in affecting the crystallographic orientation and interfaces distribution in the Al₂O₃/YAG/ZrO₂ eutectic since the interfaces of Al₂O₃/ZrO₂ and YAG/ZrO₂ with lower interfacial energy can be formed more easily during directional solidification. Therefore, the contents of Al₂O₃/ZrO₂ and YAG/ZrO₂ interfaces are higher. This study can provide theoretical guidance for interface design of multi-phase materials.     

Profiling hot isostatically pressed canister–wasteform interaction for Pu-bearing zirconolite-rich wasteforms

Zirconolite-rich full ceramic wasteforms designed to immobilize Pu-bearing wastes were produced via hot isostatic pressing (HIP) using stainless steel (SS) and nickel (Ni) HIP canisters. A detailed profiling of the elemental compositions of the major and minor phases over the canister–wasteform interaction zone was performed using scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDS) characterization. Bulk sample analyses from regions near the center of the HIP canister were also conducted for both samples using X-ray diffraction and SEM-EDS. The sample with the Ni HIP canister showed almost no interaction zone with only minor diffusion of Ni from the inner wall of the canister into the near-surface region of the wasteform. The sample with the SS HIP canister showed ∼100–120 μm of interaction zone dominated by high-temperature Cr diffusion from canister materials to the wasteform with the Cr predominantly incorporated into the durable zirconolite phase. We also examined, for the first time, changes to the HIP canister wall thickness caused by HIPing and demonstrated that no canister wall thinning occurred. Instead, in the areas examined, the canister wall thickness was observed to increase (up to ∼20%) due to the compression occurring during the HIP cycle. Further, only sparse formation of (Cr, Mn)-rich oxide particles were noted within the HIP canister inner wall area immediately adjacent to the ceramic material, with no evidence for reverse diffusion of ceramic materials. Though the HIP canister–wasteform interaction extends to ∼120 μm when using an SS HIP canister for the system investigated, this translates to <<1 vol.% for an industrial scale HIPed wasteform. Importantly, the HIP canister–wasteform interactions did not produce any obviously less durable phases in the wasteform or had any detrimental impact on the HIP canister properties.     

Heterogeneous Bimetallic Mo-NiPx/NiSy as a Highly Efficient Electrocatalyst for Robust Overall Water Splitting

Highly efficient electrocatalysts composed of earth-abundant elements are desired for water-splitting to produce clean and renewable chemical fuel. Herein, a heteroatomic-doped multi-phase Mo-doped nickel phosphide/nickel sulfide (Mo-NiP_x/NiS_y) nanowire electrocatalyst is designed by a successive phosphorization and sulfuration method for boosting overall water splitting (both oxygen and hydrogen evolution reactions (HER)) in alkaline solution. As expected, the Mo-NiP_x/NiS_y electrode possesses low overpotentials both at low and high current densities in HER, while the Mo-NiP_x/NiS_y heterostructure exhibits high active performance with ultra-low overpotentials of 137, 182, and 250 mV at the current density of 10, 100, and 400 mA cm⁻² in 1 m KOH solution, respectively, in oxygen evolution reaction. In particular, the as-prepared Mo-NiP_x/NiS_y electrodes exhibit remarkable full water splitting performance at both low and high current densities of 10, 100, and 400 mA cm⁻² with 1.42, 1.70, and 2.36 V, respectively, which is comparable to commercial electrolysis.     

Deformation-induced bonding of polymer films below the glass transition temperature

Bonding between polymers through interdiffusion of macromolecules is a well-known mechanism of polymer adhesion. A new polymer bonding mechanism in the solid state, taking place at ambient temperatures well below the glass transition value (T_g), has been recently reported; in this mechanism, bulk plastic compression of polymer films held in contact led to adhesion over timescales of the order of a fraction of a second. In this study, we prepared various blends of plasticized polymer films with desirable ductility from amorphous and semicrystalline powders of hydroxypropyl methylcellulose and polyvinyl alcohol derivatives; then, we observed the bonding of these polymers at ambient temperatures, up to 80 K below T_g, purely through mechanical deformation. The deformation-induced bonding of the polymer films studied in this work led to interfacial fracture toughnesses in the range of 1.0–21.0 J/m² when bulk plastic strains between 3% and 30% were imposed across the films. Scanning electron microscopy observation of the debonded interfaces also confirmed that bonding was caused by deformation-induced macromolecular mobilization and interpenetration. These results expand the range of applicability of sub-T_g, solid-state, deformation-induced bonding processes.     

Biochemical Investigation of the Interaction of pICln,RioK1 and COPR5 with the PRMT5–MEP50 Complex

The PRMT5–MEP50 methyltransferase complex plays a key role in various cancers and is regulated by different protein–protein interactions. Several proteins have been reported to act as adaptor proteins that recruit substrate proteins to the active site of PRMT5 for the methylation of arginine residues. To define the interaction between these adaptor proteins and PRMT5, we employed peptide truncation and mutation studies and prepared truncated protein constructs. We report the characterisation of the interface between the TIM barrel of PRMT5 and the adaptor proteins pICln, RioK1 and COPR5, and identify the consensus amino acid sequence GQF[D/E]DA[E/D] involved in binding. Protein crystallography revealed that the RioK1 derived peptide interacts with a novel PPI site.     

Tribological and corrosion behaviors of fluorocarbon coating reinforced with sodium iron titanate platelets and whiskers

A series of sodium iron titanate (NFTO)–fluorocarbon composite coatings have been prepared with the liquid-phase blending method. The effects of two types of NFTO, NFTO platelets, and NFTO whiskers, on the tribological and corrosion behaviors of the composite coatings, are systematically studied. The results show that the addition of NFTO can significantly enhance the friction-reducing and wear resistance performances of the fluorocarbon coating. Under dry sliding, the minimum specific wear rate is 1.67 × 10⁻⁴ mm³/Nm for the platelet-filled composite coatings and 1.15 × 10⁻⁴ mm³/Nm for the whisker-filled composite coatings, respectively, showing a decrease of 83.5 and 88.6% than that of pure coating. Under a simulated seawater environment, the minimum specific wear rate is 5.44 × 10⁻⁵ mm³/Nm for the platelet-filled composite coatings and 0.84 × 10⁻⁵ mm³/Nm for the whisker-filled composite coatings, respectively, showing a decrease of 90.5 and 98.5% than that of pure coating. The morphologies of worn surfaces, wear debris, and transfer films are analyzed, and the corresponding wear resistance mechanisms are discussed. The electrochemical impedance spectroscopy certifies a remarkably improved corrosion resistance of the composite coatings which have been immersed in 3.5 wt % NaCl solution for 30 days. The composite coating reinforced with 7.5 wt % platelets shows the highest resistance of 256.3 × 10⁶ Ω·cm², approximately two orders of magnitude higher than that of pure coating. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48936.     

Submicron laser-textured vents for self-cleaning injection molds

Clogging of venting slots in injection molds is a common maintenance problem caused by the degradation and the accumulation of gaseous and volatiles by-products of polymer melting. In this work, the effect of laser-induced periodic surface structures on the self-cleaning properties of venting slots is investigated. The degradation of poly(ethylene terephthalate) (PET) over different surfaces is characterized by reproducing the mechanisms that occurs in mold cavities when the air is pushed through the venting channel. An imaging technique is developed for the quantification of the sediment that deposits on sample surfaces due to condensation of by-products of PET melting. The experimental results indicate that the use of a multiscale texture minimizes the deposition of residues on the vent surface reducing it from 17.2 to 3.1%. A linear dependency between contact angle and clogging ratio indicates the efficacy of the model that explains vent self-cleaning properties considering their wetting properties.     

Statistical design of sustainable composites from poly(lactic acid) and grape pomace

Biocomposites from poly(lactic acid) (PLA) and grape pomace (GP) were created via injection molding to examine the effects of GP in a PLA matrix. To optimize the mechanical performance the biocomposites were compatibilized with maleic anhydride grafted PLA (MA-g-PLA). The objective of this work was to create a model that could accurately predict the mechanical properties of GP/PLA biocomposites. A region of feasibility for the biocomposites was determined using a statistical design of experiments. Linear regression was used to model the mechanical performance and predicted results with an error of 10% for both tensile and flexural strength and 16% for impact strength. The model was verified with a biocomposite of PLA/GP/MA-g-PLA with a ratio of 62/36/2. This biocomposite had a tensile strength, flexural modulus, and impact strength of 25.8 MPa, 40.0 MPa, and 18.4 J/m, respectively. It was found that a linear model can accurately predict the mechanical properties of PLA/GP/MA-g-PLA biocomposites.