爆破位置对深凹露天矿山炮烟扩散的影响研究

深凹露天矿山由于其特殊的结构,爆破产生的炮烟扩散稀释较为困难,严重危害生产作业人员的生命安全与健康。基于实际矿山构建了深凹露天矿山的二维物理及数学模型,采用非稳态数值分析方法研究了不同爆破位置下,深凹露天矿山采坑内爆破炮烟的扩散规律。研究结果表明：不同爆破位置下,露天采坑内均出现复环流,爆破点位置是影响露天采坑内风流结构特征的重要因素；露天采坑内的炮烟最高浓度均随着时间变化而逐渐下降,但下降的速率逐步减小,呈现三个阶段的下降趋势；爆破位置位于背风侧时露天采坑内的炮烟最高浓度和降至安全浓度所需时间远高于迎风侧三个爆破位置；随着背风侧爆破点距采坑底部距离的减小,炮烟最高浓度及降至安全浓度所需时间先降低后增加,炮烟最高浓度及降至安全浓度所需时间随着迎风侧爆破位置距采坑底部距离的减小而增加。研究结果对于指导深凹露天矿山企业合理组织爆破后的生产作业和保障作业人员安全具有重要意义。     

Investigation of fabrication of gas diffusion substrate for proton exchange membrane fuel cells

The gas diffusion substrate (GDS) is essential in the proton exchange membrane fuel cells. Its fabrication techniques affect the performance significantly and are worthy of investigation. In this study, a manufacturing process of the GDS is proposed to understand the formation process of GDS and promote its structure and performance more pertinently. Different states during the preparation process, raw carbon paper, pre-curing, curing, carbonation, and graphitization, are characterized and measured. Experimental and numerical methods are employed to determine the relationships between microstructure, transport, and mechanical performance variation with the fabricating processes. The results show that its porosity, average pore size, and effective diffusivity decrease first and increase after curing. These parameters after graphitization are lower than that of the carbon paper (CP). The electrical resistivity increases dramatically while pre-curing and decreases gradually after curing, carbonation, and graphitization, and it is much reduced after graphitization. Moreover, mechanical measurement results show that both the picks of tensile strength and flexural modulus occur after curing. Its tensile strength shows little change after graphitization compared to the initial paper's. In contrast, the flexural modulus is improved significantly.     

One-step to prepare high-performance gas diffusion layer (GDL) with three different functional layers for proton exchange membrane fuel cells (PEMFCs)

Gas diffusion layer (GDL) is one of the most important components of fuel cells. In order to improve the fuel cell performance, GDL has developed from single layer to dual layers, and then to multiple layers. However, dual or multi layers in GDL are usually prepared by layer-by-layer methods, which cost too much time, energy, and resources. In this work, we successfully developed a facile one-step method to prepare a GDL with three functional layers by utilizing the different sedimentation rates and filtration rates of short carbon fiber (CF) and carbon nanotube (CNT). The treatment temperature for this GDL is much lower than that of traditional method. The thickness of the GDL can be effectively controlled from as thin as 50 μm to more than 200 μm by simply adjusting the content of CF. The GDL with high flexibility is suitable to develop high performance flexible electronics. The fuel cell with the GDL has the maximum power density 1021 mW cm^?2, which shows 19% improvement comparing to the conventional one. Therefore, this work breaks the traditional concept that GDL for fuel cells only can be prepared by very complex and high-cost procedure.     

Study on ice-melting performance of gradient gas diffusion layer in proton exchange membrane fuel cell

In this study, a three-dimensional model was established using the lattice Boltzmann method (LBM) to study the internal ice melting process of the gas diffusion layer (GDL) of the proton exchange membrane fuel cell (PEMFC). The single-point second-order curved boundary condition was adopted. The effects of GDL carbon fiber number, growth slope of the number of carbon fibers and carbon fiber diameter on ice melting were studied. The results were revealed that the temperature in the middle and lower part of the gradient distribution GDL is significantly higher than that of the no-gradient GDL. With the increase of the growth slope of the number of carbon fiber, the temperature and melting rate gradually increase, and the position of the solid-liquid interface gradually decreases. The decrease in the number of carbon fibers has a similar effect as the increase in the growth slope of the number of carbon fibers. In addition, as the diameter of the carbon fiber increases, the position of the solid-liquid interface gradually decreases first and then increases.     

Numerical simulation of a PEM fuel cell: Effect of tortuosity parameters on the construction of polarization curves

Fuel cells (PEMFCs) are considered a clean alternative for the production of electricity. To improve their efficiency, it is necessary to understand the transport phenomena that determine their performance. This work analyzes the effective diffusion coefficients in the gas diffusion and catalyst layers (GDL and CL, respectively) based on theories such as effective medium approximation and percolation theory of a 3D multiphase nonisothermal model of a single channel PEMFC. We calculate polarization curves with different effective diffusion models and tortuosity factors m, n using OpenFOAM. The best model that approaches to experimental data is the Tomadakis-Sotirchos model with n = 4.0. The exponent m that represents the tortuosity due to the geometry has a high impact on the polarization curve construction compared to the exponent n. High values of diffusibility do not mean high values of current densities showing that there are other phenomena involved, such as water flooding.     

Microstructure,mechanical, tribological,and oxidizing properties of AlCrSiN/AlCrVN/AlCrNbN multilayer coatings with different modulated thicknesses

Multilayer structure design is one of the most promising methods for improving the comprehensive performance of AlCrN-based hard coatings applied to cutting tools. In this study, four types of AlCrSiN/AlCrVN/AlCrNbN multilayer coatings, with different modulated thicknesses, were deposited to investigate their microstructure, mechanical, tribological, and oxidizing properties. All multilayer coatings exhibited grain growth along the crystallographic plane of (200) with a NaCl-type face-centered cubic (FCC) structure. The results show that, as the modulation thickness decreases from ～35 nm to ～10 nm, (1) the grain refinement effect is increasingly evident; (2) all multilayer coatings show a hardness of >30 GPa and an elastic modulus of >300 GPa. Both the ability to resist elastic strain to failure and the plastic deformation of multilayer coatings increase. In addition, their resistance to cracking reduces; (3) the wear rates of these multilayer coatings reduce successively from 1.78 × 10^?16 m³ N^?1 m^?1 to 7.7 × 10^?17 m³ N^?1 m^?1. This is attributed to an increase in self-lubricating VO_x and a decrease in adhesives from the counterparts; (4) the best high-temperature oxidation resistance was obtained for the multilayer coating with a modulated thickness of ～15 nm.     

Effect of Pr-Ga dual-alloys diffusion on magnetic properties and thermal stability of hot-deformed PrNd-Fe-B magnets

To investigate the influence of the addition of Pr–Ga alloys on magnetic properties and morphology of materials, the hot-deformed PrNd-Fe-B magnets were prepared by the addition of Pr–Ga alloys using a dual-alloys diffusion. The room-temperature coercivity of the hot-deformed PrNd-Fe-B magnets increases substantially from 1.68 to 2.34 T, while the remanence decreases from 1.42 to 1.24 T, by the addition of 5 wt% Pr–Ga alloys. Moreover, the thermal stability of coercivity improves from ?0.46%/^oC to ?0.42%/^oC. Two types of grain boundary phases (PrNd-rich and PrNd-Ga-rich) are generated at grain boundaries by microstructural analysis, resulting in the decrease of Fe element concentration from more than 60% to about 10% at grain boundaries. The decrease of ferromagnetic element concentration at grain boundaries and the refinement of grain are considered to be the main reasons for the improvement of coercivity and thermal stability.     

α钛富氧层增厚动力学模型

为了实现在工业化生产中对α钛富氧层厚度预测和控制,通过实验研究α钛富氧层在高温空气环境中的形成及增厚过程,讨论热处理温度和时间的影响作用,建立高温(750~850℃)空气环境下关于温度、时间的富氧层增厚动力学模型。结果表明:当恒温热处理温度为750~850℃时,α钛富氧层厚度x与保温时间t0.5呈正比例关系,且升高热处理温度可显著提高富氧层增厚速度。在此温度范围内,氧原子的扩散激活能约为203473 J/mol,计算曲线与实验数据吻合性较好。结合文献中已有的扩散系数方程和实验测得的富氧层厚度数据,推导得到5个富氧层增厚动力学方程,其中3个方程的计算曲线与实验数据吻合性较好,可为实际生产中预估富氧层厚度提供理论支持。     

钨中空位及其团簇的能量学和动力学性质参数

在总结前人钨中空位及其团簇的能量学和动力学行为的研究成果基础上，采用第一性原理方法系统计算了钨中空位及其团簇的结合能和扩散能垒。研究发现，交换关联泛函PW91和PBE较PBEsol、AM05和LDA更适合用于计算钨空位的能量学性质。基于第一性原理计算结果对文献中单空位形成能、双空位作用性质等争议性问题进行了讨论，并对钨经验势进行了评估。研究结果表明，钨中孤立单空位间总是相互排斥，而空位团簇（V_n>3）对单空位具有很强的吸引作用，其结合能随着所含空位个数增多呈现波动性增大的趋势。空位团簇稳定结构可通过最小化Wigner-Seitz表面积来确定，其结合能与V_n与V_n-1之间的Wigner-Seitz面积之差呈正比。     

Kinetic analysis of crystallization of zeolite beta synthesized by direct heating

To quantitatively investigate the initial crystallization of zeolite beta synthesized by direct heating, the extent of the reaction was precisely evaluated by X-ray diffraction measurements and Rietveld structural refinement, and a kinetic analysis of crystallization was performed using the Avrami-Erofe'ev equation. The activation energy for crystallization was lower than that for hydrothermal synthesis. Reaction and synthesis time curves revealed that the initial zeolite beta crystallization consisted of three stages. The first was an induction period with nucleation by the generation of building units and the formation of an initial coordinated structure. The second stage was crystal growth by a diffusion-controlled reaction, and the third stage involved slowing down of crystallization by the limitation of dehydrocondensation. These stages could be analyzed by calculation of the rate constant and Avrami exponent for each stage.