微纳层叠聚丙烯腈凝胶流动特性的数值模拟研究

建立了层叠流道的三维模型和有限元网格模型，根据流变测试数据，采用Polymat对物料的黏度模型参数进行拟合，并利用Polyflow软件对聚丙烯腈（PAN）凝胶在层叠流道内的三维等温流动过程进行了数值模拟分析。研究发现，当入口流量增大时，层叠流道出口速度的不均匀性增加；沿流动方向流道内压力逐渐降低，并在出口处降低至同一最低值；流道进出口压力差与入口流量大小具有正相关性；在流道的中心截面上剪切速率分布均匀，波动较小。     

Low/intermediate temperature pyrolyzed polysiloxane derived ceramics with increased carbon for electrical applications

This study focuses on the chemistry, thermal stability, and electrical conductivity of low/intermediate pyrolysis temperature (700?900 °C) polysiloxane derived ceramics. These ceramics were modified with additional carbon derived from divinylbenzene (DVB) added to the precursor. Their electrical properties were investigated for potential uses in micro-electrical mechanical systems (MEMS) and anodes for lithium batteries. The microstructure and chemical composition was investigated by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), Raman spectroscopy, and x-ray photoelectron spectroscopy (XPS); thermogravimetric analysis (TGA) provided insight into the thermal stability; and electrochemical impedance spectroscopy (EIS) into the electrical properties of the material. The increase of pyrolysis temperature and carbon content lead to an enhancement of the electrical conductivity, higher than previously reported values for intermediate pyrolysis temperature SiOC polymer derived ceramics. A limit of the amount of DVB that can be added to PHMS to produce a hybrid precursor has also been obtained.     

Facile synthesis of a carbon-rich SiAlCN precursor and investigation of its structural evolution during the polymer-ceramic conversion process

A liquid carbon-rich SiAlCN precursor is facilely synthetized by hydrosilylation between liquid polyaluminocarbosilane (LPACS) and 1,3,5,7-tetravinyl- 1,3,5,7-tetramethylcyclotetrasilazane {[CH₃(CH₂CH₂)SiNH]₄} (TeVSZ). The structural evolution during the polymer-ceramic conversion process is investigated by various methods. The results show that the main cured mechanism is β-addition on hydrosilylation, although α-addition on hydrosilylation, polymerization of vinyl groups and dehydrocoupling reaction between N–H bonds also occur during the cured process. During the pyrolysis process, dehydrogenation and dehydrocarbonation condensation reactions, transamination reactions occur, leading to formation of a three-dimensional network inorganic structure at 400–800 °C, where part of Al–O bonds convert to Al–N bonds. Then the network inorganic structure undergoes demixing and separation into amorphous SiAlCN(O) phase, where the amorphous turbostratic free carbon phase also form at 800–1200 °C. With demixing and decomposition of the amorphous carbon-rich SiAlCN(O) phase, the crystalline β-SiC and graphitic carbon start to form at about 1400 °C, the crystalline sizes of them both enlarge with increasing temperature. However, the crystal growth of β-SiC is distinctly inhibited due to existence of the rich carbon phase, tiny amounts of Al₂O₃ and AlN. In addition, a small amount of AlN can promote the formation of α-SiC at 1800 °C.     

Solution precursor thermal spraying of gadolinium zirconate for thermal barrier coating

Gadolinium zirconate (GZ) is an attractive material for thermal barrier coatings (TBCs). However, a single layer GZ coating has poor thermal cycling life compared to Yttria Stabilized Zirconia (YSZ). In this study, Solution Precursor High Velocity Oxy-Fuel (SP-HVOF) thermal spray was used to produce a double layer GZ/YSZ TBC and compared the thermal cycling performance with the single layer YSZ TBC. The temperature behaviour of the solution precursor GZ was studied, and single splat tests were carried out to obtain an optimised spray parameter. In thermal cycling tests, the single-layer YSZ reached 20 % failure at 85 ± 5 cycles, whereas the double-layer GZ/YSZ was at 70 ± 15 cycles. The single-layer failed at the topcoat/TGO interface, whereas the double-layer failed at GZ/YSZ interface and topcoat/TGO interface. Moreover, Gd diffusion occurred near the GZ/YSZ interface, resulting in porosities in the GZ layer.     

Molecular Characteristics of Amyloid Precursor Protein (APP) and Its Effects in Cancer

Amyloid precursor protein (APP) is a type 1 transmembrane glycoprotein, and its homologs amyloid precursor-like protein 1 (APLP1) and amyloid precursor-like protein 2 (APLP2) are highly conserved in mammals. APP and APLP are known to be intimately involved in the pathogenesis and progression of Alzheimer’s disease and to play important roles in neuronal homeostasis and development and neural transmission. APP and APLP are also expressed in non-neuronal tissues and are overexpressed in cancer cells. Furthermore, research indicates they are involved in several cancers. In this review, we examine the biological characteristics of APP-related family members and their roles in cancer.     

Zirconia-alumina multiphase ceramic fibers with exceptional thermal stability by melt-spinning from solid ceramic precursor

Zirconia-alumina multiphase ceramic fibers with 80 wt% (Z80A20 fiber) and 10 wt% (Z10A90 fiber) proportions of zirconia were prepared via melt-spinning and calcination from solid ceramic precursors synthesized by controllable hydrolysis of metallorganics. The zirconia-alumina multiphase fibers had a diameter of about 10 µm and were evenly distributed with alumina and zirconia grains. The Z80A20 and Z10A90 ceramic fibers had the highest filament tensile strength of 1.78 GPa and 1.87 GPa, respectively, with a peak value of 2.62 GPa and 2.71 GPa. The Z80A20 ceramic fiber has superior thermal stability compared to the Z10A90 ceramic fiber and a higher rate of filament strength retention due to the stability in grain size. After heat treatment at 1100 °C, 1200 °C, and 1300 °C for 1 h respectively, the filament tensile strength retention rate of Z80A20 ceramic fibers was 87 %, 80 %, and 40 %. While Z10A90 ceramic fiber was fragile after being heated at 1300 °C. The results showed that the high zirconia content facilitated the fiber's thermal stability.     

Synthesis of highly efficient,structurally improved Li4SiO4 sorbents for high-temperature CO2 capture

Li₄SiO₄ sorbents for high-temperature CO₂ removal have drawn extensive attention owing to their potential application in carbon capture and storage (CCS). The major challenge in the application lies in the poor CO₂ capture performance under realistic conditions of low CO₂ concentrations, owing to the dense structure and poor porosity. In this work, Li₄SiO₄ sorbents were prepared with porous micromorphologies and large contact areas using a variety of organometallic Li-precursors, achieving fast CO₂ sorption kinetics, high capacity and excellent cyclic stability at a low CO₂ concentration (15?vol%). It was found that a high conversion of ~?74% was maintained for pure Li₄SiO₄ even after 100 sorption/desorption cycles. Moreover, by doping with Na₂CO₃ to reduce the CO₂ diffusion resistance, the conversion of the sorbent was further enhanced to 93.2%. The enhancement mechanism of alkali carbonate have been proven here to be ascribed to the formation of the eutectic melt of Li/Na carbonates, the existence and function of which has been confirmed in this study.     

Characteristics of polycarbosilanes produced under different synthetic conditions and their influence on SiC fibers: Part I

SiC fibers can be obtained by the spinning, curing, and heat treatment of polycarbosilane (PCS); however, the properties of the PCS precursor must be considered to set the correct spinning conditions. Although many studies have focused on the synthesis conditions, the characterization (in particular, the structural characteristics) of PCS fibers, and the polymer itself has limitations. In this study, PCS was prepared in two steps, and the growth of the polymer with respect to the reaction conditions was analyzed. We found that PCS is formed and grown by the rearrangement and subsequent condensation reactions of polydimethylsilane (PDMS). Further, fiber formation was affected by the reaction temperature, time, and pressure. Three types of PCS were obtained under different synthetic conditions, and they were all characterized. Regardless of the structural similarity of the PCS fibers (based on the spectroscopic analysis), the polymers showed different thermal and rheological properties. Our findings will be important in improving the production of PCS fibers (and subsequent SiC fibers) with finely controlled properties.     

Fabricating NixCo1−xO@C cocatalysts sensitized by CdS through electrostatic interaction for efficient photocatalytic H2 evolution

Exploiting efficient and stable noble metal-free hydrogen evolution catalysts for water splitting is of great importance. In this work, Ni_xCo_1-xO@C/CdS hybrid is successfully fabricated through an electrostatic interaction of oppositely charged nanoparticles on their surfaces. The resulting Ni_xCo_1-xO@C nanoboxes cocatalysts which were derived from NiCo-LDH@ZIF-67 with Ni–Co layered double hydroxides (LDH) decorated with ZIF-67 precursor exhibited improved hydrogen production rate compared with bare CdS semiconductor from 0.7 mmol g⁻¹ h⁻¹ to 56 mmol g⁻¹ h⁻¹. It is demonstrated that the electrostatic interaction between the two surface charged nanoparticles of Ni_xCo_1-xO@C and CdS play an important role in migrating and separating of photogenerated charge carriers. The synthesized Ni_xCo_1-xO@C as excellent candidates for cost-effective cocatalysts is aimed to substitute for noble metals in photocatalytic H₂ evolution.