Direct ink writing of vancomycin-loaded polycaprolactone/ polyethylene oxide/ hydroxyapatite 3D scaffolds

Novel inks were formulated by dissolving polycaprolactone (PCL), a hydrophobic polymer, in organic solvent systems; polyethylene oxide (PEO) was incorporated to extend the range of hydrophilicity of the system. Hydroxyapatite (HAp) with a weight ratio of 55–85% was added to the polymer-based solution to mimic the material composition of natural bone tissue. The direct ink writing (DIW) technique was applied to extrude the formulated inks to fabricate the predesigned tissue scaffold structures; the influence of HAp concentration was investigated. The results indicate that in comparison to other inks containing HAp (55%, 75%, and 85%w/w), the ink containing 65% w/w HAp had faster ink recovery behavior; the fabricated scaffold had a rougher surface as well as better mechanical properties and wettability. It is noted that the 65% w/w HAp concentration is similar to the inorganic composition of natural bone tissue. The elastic modulus values of PCL/PEO/HAp scaffolds were in the range of 4–12 MPa; the values were dependent on the HAp concentration. Furthermore, vancomycin as a model drug was successfully encapsulated in the PCL/PEO/HAp composite scaffold for drug release applications. This paper presents novel drug-loaded PCL/PEO/HAp inks for 3D scaffold fabrication using the DIW printing technique for potential bone scaffold applications.     

Polysorbate identity and quantity dictate the extensional flow properties of protein-excipient solutions

While protein medications are promising for treatment of cancer and autoimmune diseases, challenges persist in terms of development and injection stability of high-concentration formulations. Here, the extensional flow properties of protein-excipient solutions are examined via dripping-onto-substrate extensional rheology, using a model ovalbumin (OVA) protein and biocompatible excipients polysorbate 20 (PS20) and 80 (PS80). Despite similar PS structures, differences in extensional flow are observed based on PS identity in two regimes: at moderate total concentrations where surface tension differences drive changes in extensional flow behavior, and at small PS:OVA ratios, which impact the onset of weakly elastic flow behavior. Undesirable elasticity is observed in ultra-concentrated formulations, independent of PS identity; higher PS contents are required to observe these effects than in analogous polymeric excipient solutions. These studies reveal novel extensional flow behaviors in protein-excipient solutions, and provide a straightforward methodology for assessing the extensional flow stability of new protein-excipient formulations.     

Effect of laver powder on textual,rheological properties and water distribution of squid (Dosidicus gigas) surimi gel

In order to ameliorate the gel quality of Dosidicus gigas surimi, the effects of laver powder on gel properties, rheological properties, and water-holding capacity (WHC) were investigated. Results indicated that the addition of laver powder could significantly increase the hardness, chewiness, and breaking force of surimi gels. However, the texture indexes and gel strength began to decline when additional amount exceeded 0.6%. Rheological results demonstrated that the addition of laver powder increased the storage modulus (G′) and viscosity of surimi, prolonged protein denaturation temperature in surimi gels. Moreover, the WHC of surimi gel was improved with the increase of laver powder. Further analyses in low-field nuclear magnetic resonance revealed that laver powder could shorten the transverse relaxation time, enhanced the combination with water, and altered the distribution of different water categories. The proportion of bound water and immobilized water reached its maximum and minimum at 0.6% of laver powder, respectively. Correlation analyses showed that WHC of surimi gel was negatively correlated well with the proportion of loose-bound water, but positively correlated with the strong-bound water and free water. In conclusion, the results supported that 0.6% was the optimal additional amount of laver powder for the squid-based surimi production based on the current ingredients of surimi products.     

Effect of different fibres on texture,rheological and sensory properties of acid casein processed cheese sauces

The objective of this study was the evaluation of different fibres (bamboo, acacia, potato or citrus) addition on texture, rheological and sensory properties of acid casein processed cheese sauces. Fibres used in production of sauces had an impact on the texture, viscosity, viscoelastic and sensory properties. The largest increase in viscosity was observed in products with addition of potato fibre, which have good water holding and adsorption capacity. Processed cheese sauce with the addition of citrus fibre was characterised by the highest values in general, and the increase of this feature in the tested samples was regular. Adhesiveness was the highest in products with 1% addition of every fibre. The lowest values of viscosity single shear, G′ and G″ moduli, among all tested, had sauces with acacia fibre. Moreover, they had the most thin liquid consistency, which was different from preferred one.     

The use of bio-diesel based additive as rheology improver and pour point depressant of Nigerian waxy crude

The chemical method has proved to be the most effective mitigating method of wax deposition in petroleum system as it deals with the root cause of wax formation. Most of the commercial chemicals in the industry are very expensive and toxic. This paper aims the use of biodiesel based additives for improving the rheological behavior and pour points of waxy crude from Nigeria field. The biodiesels derived additives gave better performance than the commercial chemical and the seed oils as greatly improvement in rheology and pour point values of the waxy crude were observed     

Influence of tetraploid wheat (Triticum dicoccum) on low glycaemic index pizza base processing and its starch digestibility

The present study aimed to utilise Dicoccum wheat (DW), barley (BF) and soya flour (SF) in the development of low in vitro starch digestibility (IVSD) and estimated glycaemic index (EGI) PB. The BF and SF are mixed (1:1) (BFSF) and used to replace DW at 25%, 50% and 75% level and compared with 100% DW. The quality characteristics (rheological, physical, textural and chemical), IVSD and EGI of PB were determined. The incorporation of BFSF to DW increased the farinograph water absorption capacity (58.1%–64.2%) and mixing tolerance index (21-68 FU), and decreased the dough development time (4.3–2.8 min) and amylograph pasting properties, respectively. Further, the thickness, shear force and redness were decreased and lightness and yellowness increased. Based on the physico-sensory studies, 50% of BFSF along with emulsifier’s incorporation was optimum without affecting any sensory parameters and this PB had decreased IVSD (31) and EGI (54) when compared to the control 37 and 63, respectively.     

The effect of rice bran on physicochemical,textural and glycaemic properties of ready-to-eat extruded corn snacks

In this work, corn extruded snack products were enriched with rice bran (RB) at 10% and 15%. A co-rotating twin-screw extruder was used with a feed moisture content of 16 g 100 g⁻¹, a screw speed of 240 r.p.m. and four heating sections of the barrel (100, 140, 150 and 150 °C). The impact of RB inclusion on nutritional profile, starch digestion, physicochemical and textural properties of snack products was evaluated. RB-enriched extrudates showed a lower specific volume and hardness and higher crispness than control. RB at 15% gave a water-holding capacity lower than control. Rheology of extrudate dispersions indicated an increase in elastic interactions and solid-like behaviour with RB supplementation. Differences in rheological properties resulted in attenuation of predictive glycaemic response for RB-enriched snacks.     

An experimental approach towards increasing mechanical durability of extruded fish feed in the drying process

Mechanical durability of extruded fish feed must be optimized to lower economic losses as well as emission of organic matter to aquatic environments. The glass transition hypothesis for viscoelastic biopolymers is demonstrated and confirmed experimentally to be valid for extruded fish feed pellets. It is proposed and demonstrated that it is important to avoid early glass transition onset, to optimize the obtained mechanical durability. From the proposed glass transition hypothesis, immediate process relevance to the pre-drying transport mechanism is demonstrated. Furthermore, measured mechanical durability is found to range from 1.5 to 5.0% loss, for different combinations of drying parameters.