Achieving fabrication of highly transparent Y2O3 ceramics via air pre-sintering by deionization treatment of suspension

An easy albeit quite effective deionization suspension treatment was adopted to alleviate the detrimental effects related to the hydrolysis of Y₂O₃ in an aqueous medium. Fabrication of highly transparent Y₂O₃ ceramics with a fine grain size via air pre-sintering and post–hot isostatic pressing (HIP) treatment without using any sintering additive was achieved using the treated suspensions. The hydrolysis issue of Y₂O₃ powder in an aqueous medium was effectively alleviated by using deionization treatment, and a well-dispersed suspension with a low concentration of dissolved Y³⁺ species was obtained. The dispersed suspensions were consolidated by the centrifugal casting method, and the green bodies derived from the suspension of 35.0 vol% solid loading showed an improved homogeneity with a relative density of 52.1%. Fully dense Y₂O₃ transparent ceramic with high transparency was obtained by pre-sintering consolidated green compacts at a low temperature of 1400°C for 16 h in air followed by a post-HIP treatment at 1550°C for 2 h under 200 MPa pressure. The sample had a fine average grain size of 690 nm. The in-line transmittance of the sample reached 83.3% and 81.8% at 1100 nm and 800 nm, respectively, very close to the theoretical values of Y₂O₃.     

PUL-Mediated Plant Cell Wall Polysaccharide Utilization in the Gut Bacteroidetes

Plant cell wall polysaccharides (PCWP) are abundantly present in the food of humans and feed of livestock. Mammalians by themselves cannot degrade PCWP but rather depend on microbes resident in the gut intestine for deconstruction. The dominant Bacteroidetes in the gut microbial community are such bacteria with PCWP-degrading ability. The polysaccharide utilization systems (PUL) responsible for PCWP degradation and utilization are a prominent feature of Bacteroidetes. In recent years, there have been tremendous efforts in elucidating how PULs assist Bacteroidetes to assimilate carbon and acquire energy from PCWP. Here, we will review the PUL-mediated plant cell wall polysaccharides utilization in the gut Bacteroidetes focusing on cellulose, xylan, mannan, and pectin utilization and discuss how the mechanisms can be exploited to modulate the gut microbiota.     

2种侧围加强内框总成检具结构对比分析

概述了侧围加强内框总成与周边零件的匹配关系,从检具操作的人机工程出发,描述了侧围加强内框总成检具的2种定位方式和结构设计,对比了2种定位方式对于检测结果的影响,总结了其优点和弊端,结果表明侧围加强内框总成检具采用车内方向朝下的定位方式效果更好。     

凌庄子水厂保水堰流量系数试验

凌庄子水厂蓄水池进水口处有一保水堰,为非标准薄壁堰,不能使用已有堰流公式对其过流量进行准确计算。为了得出较为精确的过流流量,按照重力相似准则制作几何比尺为1∶5的模型进行试验研究。在已有自由出流公式的基础上,对自由出流流量系数进行修正并对淹没情况下流量变化过程进行研究。对该非标准堰自由出流流量系数的实测值与经验值进行分析比较,发现堰板槽降低了实际自由出流过流能力。淹没出流的流量系数主要与下游尾水位有关,试验中形成的淹没式堰流受实际堰型尺寸影响,下游尾水位和堰上水位近似相等,不完全适用已有淹没出流流量公式,通过试验给出了修正淹没系数随h/p的变化关系。结果表明利用堰前、堰后水位初步计算过流流量是可行的,可为该工程提供参考,也可为实际工程中非标准矩形堰的流量计算提供思路。     

Impacts of slip and mass transpiration on Newtonian liquid flow over a porous stretching sheet

This article focuses on analytic solutions for Newtonian fluid flow with slip and mass transpiration on a porous stretching sheet using the differential transform method and Pade approximants of an exceptionally nonlinear differential equation. The impacts of different parameters including mass transpiration (suction/injection), Navier's slip, and Darcy number parameters on the velocity of the liquid and tangential stress are discussed. A comprehensive comparison of our results with the previous one in the literature is made, and the results showed good agreement. An investigation is conducted of a combination of magnetic liquids that are conceivably pertinent for wound medicines, skin repair, and astute coatings for natural gadgets. It is found that there is a decrease in the velocity profiles and the boundary layer thickness for the case of suction.     

Experimental investigation of the effects of contraction on tsunami-induced forces and pressures on a box section bridge

Many bridges that lie within possible tsunami inundation zones are critical links in transport networks. Some efforts have been made to determine the effects of tsunamis on bridges, but only a limited range of published design guidelines are available. Therefore, it is necessary to further investigate the effects of tsunamis on bridges. In the current study, physical modeling experiments were carried out to measure bore impact forces and pressures for various tsunami bore strengths on a bridge deck with different abutment types (wing wall and spill-through) and different opening and submergence ratios. The experiments were conducted in a wave flume with dimensions of 14 × 1.2 × 0.8 m (length × width × height), equipped with an automatic gate designed to generate a tsunami bore. The horizontal and vertical forces showed an increasing trend with increasing submergence ratio for both types of abutment. However, the horizontal force showed a decreasing trend as the opening ratio decreased, while the vertical force initially increased as the opening ratio decreased, until it reached a peak value, and then it started to decrease. The overall shapes of the results for both types of abutment are similar, with higher values for spill-through abutments due to their lower energy dissipation rates. Based on the experimental data, empirical equations are proposed for estimation of tsunami loads as a function of opening and submergence ratios.     

Large domain-wall currents in epitaxial Au/BiFeO3/SrRuO3 thin-film capacitors with modulated oxygen vacancy and wall densities

Large domain wall (DW) conductivity in an insulating ferroelectric plays an important role in the future nanosensors and nonvolatile memories. However, the wall current was usually too small to drive high-speed memory circuits and other agile nanodevices requiring high output-powers. Here, a large domain-wall current of 67.8 μA in a high on/off ratio of ~4460 was observed in an epitaxial Au/BiFeO₃/SrRuO₃ thin-film capacitor with the minimized oxygen vacancy concentration. The studies from read current-write voltage hysteresis loops and piezo-response force microscope images consistently showed remaining of partially unswitched domains after application of an opposite poling voltage that increased domain wall density and wall current greatly. A theoretical model was proposed to explain the large wall current. According to this model, the domain reversal occurs with the appearance of head-to-head and tail-to-tail 180° domain walls (DWs), resulting in the formation of highly conductive wall paths. As the applied voltage increased, the domain-wall number increased to enhance the on-state current, in agreement with the measurements of current-voltage curves. This work paves a way to modulate DW currents within epitaxial Au/BiFeO₃/SrRuO₃ thin-film capacitors through the optimization of both oxygen vacancy and domain wall densities to achieve large output powers of modern domain-wall nanodevices.     

Influence of bio-clogging on permeability characteristics of soil

It is necessary to enhance the barrier performance of cutoff walls in order to improve the contamination control level, especially for reconstruction or expansion of existing landfill sites. This paper presents a comprehensive laboratory investigation on the synergistic effects of microorganisms and fibers on the hydraulic conductivity of silty sand to evaluate the applicability to the field condition as an alterative barrier material. Inside the soil, the added carbon fibers not only provided good biocompatibility, but also formed spatial three-dimensional network between soil particles to improve the bacterial adhesion that eventually caused 2–3 orders of magnitude decrease in soil permeability. The resistance of the biofilm to extreme conditions was tested by permeation with solutions of different salinity and pH values, and by subjecting specimens to various hydraulic gradients and soil conditions. Despite the microbial growth inhibition occurred at these conditions, however, biofilm can largely remain intact and continue to reduce k, which due to the gradual adaptation of microorganisms to the extreme environment and the gradual recovery of their activity. Results of these tests demonstrate that biofilm treatment may be a feasible technology for creating waste containment barriers in soil.     

Quaternäre Metall/Metalloxid‐Katalysatoren als Wandkatalysatoren in Mikroreaktoren für Power‐to‐Gas‐Applikationen mittels kombinatorischer Hochdurchsatzmethoden

Catalysts of quaternary composition have been prepared and tested for the Sabatier process. For catalyst syntheses the following techniques have been used: sol‐gel methods, wet impregnation and incipient wetness impregnation. The Sabatier reaction was carried out at temperatures between 520 K and 670 K, pressures of 15 bar and 30 bar using a mixture H₂:CO₂ of 4:1. Activity screening of the microscale wall catalysts was performed by a custom‐built 10‐fold parallel gas‐flow microreactor setup in sequential operating mode. To analyze the gas phase compositions GC‐FID was used.