排序方式: 共有112条查询结果,搜索用时 35 毫秒
1.
A dual-band, wide tuning range voltage-controlled oscillator that uses transformer-based fourth-order(LC) resonator with a compact common-centric layout is presented. Compared with the traditional wide band(VCO), it can double frequency tuning range without degrading phase noise performance. The relationship between the coupling coefficient of the transformer, selection of frequency bands, and the quality factor at each band is investigated. The transformer used in the resonator is a circular asymmetric concentric topology. Compared with conventional octagon spirals, the proposed circular asymmetric concentric transformer results in a higher qualityfactor, and hence a lower oscillator phase noise. The VCO is designed and fabricated in a 0.18- m CMOS technology and has 75% wide tuning range of 3.16–7.01 GHz. Depending on the oscillation frequency, the VCO current consumption is adjusted from 4.9 to 6.3 m A. The measured phase noises at 1 MHz offset from carrier frequencies of 3.1, 4.5, 5.1, and 6.6 GHz are –122.5, –113.3, –110.1, and –116.8 d Bc/Hz, respectively. The chip area, including the pads, is 1.20.62 mm2 and the supply voltage is 1.8 V. 相似文献
2.
A new broadband low-noise amplifier (LNA) is proposed. The conventional common gate (CG) LNA exhibits a relatively high noise figure, so active gin-boosting technology is utilized to restrain the noise generated by the input transistors and reduce the noise figure. Theory, simulation and measurement are shown. An implemented prototype using 0.13 μm CMOS technology is evaluated using on-wafer probing. S11 and S22 are below -10 dB across 0.1-5 GHz. Measurements also show a gain of 18.3 dB with a 3 dB bandwidth from 100 MHz to 2.1 GHz and an ⅡP3 of-7 dBm at 2 GHz. The measured noise figure is better than 2.5 dB below 2.1 GHz, is better than 4.5 dB below 5 GHz, and at 500 MHz, it gets its minimum value 1.8 dB. The LNA consumes 9 mA from 1.5 V supply and occupies an area of 0.04 mm^2. 相似文献
3.
锁相环频率综合器中高性能电荷泵设计 总被引:1,自引:1,他引:0
本文基于0.18μm CMOS工艺设计并实现了一种新的高性能电荷泵电路。采用宽输入范围的轨到轨运算放大器和自偏置共源共栅电流镜技术提高了电荷泵在宽输出电压范围内的电流匹配精度;同时,提出通过增加预充电电流源技术来提高电荷泵的初始充电电流,以缩短CPPLLs的建立时间。测试结果表明电荷泵在0.4~1.7V输出电压范围内失配电流小于0.4%,充电电流为100μA,预充电电流为70μA。在1.8V电源电压下,电荷泵电路锁定时的平均功耗为0.9mW。 相似文献
4.
应用于无线传感器网络的低噪声放大器设计 总被引:1,自引:0,他引:1
给出一种基于SMIC0.13μm RFCMOS工艺、应用于无线传感器网络2.4GHz的低噪声放大器设计。设计目标为在2.43GHz的中心频率下带宽为120MHz,并且增益分为高20dB、中10dB及低0dB三档可调。电路采用功率和噪声优化技术,输入端采用片外电感匹配,输入输出都匹配到50Ω阻抗。在Cadence Spectre仿真环境下的后仿真结果表明:高增益时S21为21.2dB而噪声系数为0.5dB,S11为-29.8dB,S22为-20.7dB。电路在1.2V电源电压下的工作电流约为6mA。 相似文献
5.
6.
一个应用于卫星导航接收机的低功耗可配置双频多模射频前端 总被引:1,自引:1,他引:0
本文给出了一个应用于GPS、北斗、伽利略和Glonass四种卫星导航接收机的高性能双频多模射频前端。该射频前端主要包括有可配置的低噪声放大器、宽带有源单转双电路、高线性度的混频器和带隙基准电路。详细分析了寄生电容对源极电感负反馈低噪声放大器输入匹配的影响,通过在输入端使用两个不同的LC匹配网络和输出端使用开关电容的方法使低噪声放大器可以工作在1.2GHz和1.5GHz频带。同时使用混联的有源单转双电路在较大的带宽下仍能获得较好的平衡度。另外,混频器采用MGTR技术在低功耗的条件下来获得较高的线性度,并不恶化电路的其他性能。测试结果表明:在1227.6MHz和1557.42MHz频率下,噪声系数分别为2.1dB和2.0dB,增益分别为33.9dB和33.8dB,输入1dB压缩点分别0dBm和1dBm,在1.8V电源电压下功耗为16mW。 相似文献
7.
本文给出一种应用于无线传感器网络射频前端低噪声放大器的设计,采用SMIC0.18μmCMOS工艺模型。在CadenceSpectre仿真环境下的仿真结果表明:该低噪声放大器满足射频前端的系统要求,在2.45GHz的中心频率下增益可调,高增益时,噪声系数为2.9dB,输入P1dB压缩点为-19.8dBm,增益为20.5dB;中增益时,噪声系数为3.6dB,输入P1dB压缩点为-15.8dBm,增益为12.5dB;低增益时,噪声系数为6.0dB,输入P1dB压缩点为-16.4dB,增益为2.2dB。电路的输入输出匹配良好,在电源电压1.8V条件下,工作电流约为6mA。 相似文献
8.
本文利用噪声系数的Y因子法测试原理分析了四端口网络和差分网络的噪声特性及其噪声系数与双端口网络噪声系数之间的数学关系方程,测试时分别对差分网络的每个输入输出组合进行双端口噪声系数测试,然后利用该关系方程计算出差分网络的噪声系数。该方法不需要利用巴仑将差分网络转成双端口网络,从而简化了对测试设备的要求。通过对比测试表明,两种方法的测试结果相差在0.5dB以内,可以满足应用需要。 相似文献
9.
10.