Interfacial microstructure and mechanical properties of Ti3SiC2 ceramic and TC11 alloy joint diffusion bonded with a Cu interlayer

Reliable joints of Ti₃SiC₂ ceramic and TC11 alloy were diffusion bonded with a 50 μm thick Cu interlayer. The typical interfacial structure of the diffusion boned joint, which was dependent on the interdiffusion and chemical reactions between Al, Si and Ti atoms from the base materials and Cu interlayer, was TC11/α-Ti + β-Ti + Ti₂Cu + TiCu/Ti₅Si₄ + TiSiCu/Cu(s, s)/Ti₃SiC₂. The influence of bonding temperature and time on the interfacial structure and mechanical properties of Ti₃SiC₂/Cu/TC11 joint was analyzed. With the increase of bonding temperature and time, the joint shear strength was gradually increased due to enhanced atomic diffusion. However, the thickness of Ti₅Si₄ and TiSiCu layers with high microhardness increased for a long holding time, resulting in the reduction of bonding strength. The maximum shear strength of 251 ± 6 MPa was obtained for the joint diffusion bonded at 850 °C for 60 min, and fracture primarily occurred at the diffusion layer adjacent to the Ti₃SiC₂ substrate. This work provided an economical and convenient solution for broadening the engineering application of Ti₃SiC₂ ceramic.     

Effect of LiTFSI and LiFSI on Cycling Performance of Lithium Metal Batteries Using Thermoplastic Polyurethane/Halloysite Nanotubes Solid Electrolyte

All-solid-state lithium batteries(ASSLB) are promising candidates for next-generation energy storage devices.Nevertheless,the large-scale commercial application of high energy density AS S LB with the polymer electrolyte still faces challenges.In this study,a thin solid polymer composite electrolyte(SPCE) is prepared through a facile and cost-effective strategy with an infiltration of thermoplastic polyurethane(TPU),lithium salt(LiTFSI or LiFSI),and halloysite nanotubes(HNTs) in a porous framework of polyethylene separator(PE)(TPU-HNTs-LiTFSI-PE or TPU-HNTs-LiFSI-PE).The composition,electrochemical performance,and especially the effect of anions(TFSI~-and FSI~-) on cycling performance are investigated.The results reveal that the flexible TPU-HNTs-LiTFSI-PE and TPU-HNTs-LiFSI-PE with a thickness of 34 μm exhibit wide electrochemical windows of 4.9 and 5.1 V(vs.Li+/Li) at 60℃,respectively.Reduction in FSI~-tends to form more LiF and sulfur compounds at the interface between TPU-HNTs-LiFSI-PE and Li metal anode,thus enhancing the interfacial stability.As a result,cell composed of TPU-HNTs-LiFSI-PE exhibits a smaller increase in interfacial resistance of solid electrolyte interphase(SEI) with a distinct decrease in charge-transfer resistance during cycling.Li|Li symmetric cell with TPU-HNTs-LiFSI-PE could keep its stable overpotential profile for nearly 1300 h with a low hysteresis of approximately39 mV at a current density of 0.1 mA cm~(-2),while a sudden voltage rise with internal cell impedance-surge signals was observed within 600 h for cell composed of TPU-HNTs-LiTFSI-PE.The initial capacities of NCMITPU-HNTs-LiTFSIPEILi and NCMITPU-HNTs-LiFSI-PEILi cells were 149 and 114 mAh g~(-1),with capacity retention rates of 83.52% and89.99% after 300 cycles at 0.5 C,respectively.This study provides a valuable guideline for designing flexible SPCE,which shows great application prospect in the practice of ASSLB.     

Effects of the joining process on the microstructure and properties of liquid-phase-sintered SiC-SiC joints formed with Ti foil

The joining of liquid-phase sintered SiC (LPS-SiC) ceramics was conducted using spark plasma sintering (SPS), through solid state diffusion bonding, with Ti-metal foil as a joining interlayer. Samples were joined at 1400 °C, under applied pressures of either 10 or 30 MPa, and with different atmospheres (argon, Ar, vs. vacuum). It was demonstrated that the shear strength of the joints increased with an increase in the applied joining pressure. The joining atmosphere also affected on both the microstructure and shear strength of the SiC joints. The composition and microstructure of the interlayer were examined to understand the mechanism. As a result, a SiC-SiC joining with a good mechanical performance could be achieved under an Ar environment, which in turn could provide a cost-effective approach and greatly widen the applications of SiC ceramic components with complex shape.     

Surface modification of superfine SiC powders by ternary modifiers-KH560/sodium humate/SDS and its mechanism

SiC is a promising functional ceramic material with many great properties. High concentrated SiC slurry with excellent rheology and stability is required in some processes of ceramic forming. In this work, the dispersion of SiC powders was obviously improved by ternary modifiers: γ-(2,3-epoxypropoxy) propytrimethoxysilane (KH560), sodium humate and sodium dodecyl sulfate (SDS). Modified SiC slurry showed the lowest viscosity of 0.168 Pa s at a solid content of 50 vol%. The maximum absolute value of zeta potential of SiC increased from 47.3 to 61.6 mV by modification. Sedimentation experiments showed that a highly stable suspension of modified SiC was obtained at pH 10. SiC green body with high density of 2.643 g/cm³ was prepared with modified powders by slip casting. X-ray photoelectron spectra (XPS) and thermogravimetry (TG) measurements indicated the adsorption of modifiers on SiC surface. Therefore, modified SiC powders could stably disperse in aqueous media due to the increase of electrosteric repulsion between particles. The novel strategy used in this study could further improve the dispersion of SiC powders.     

Anthocyanin-fortified konjac glucomannan/sodium alginate composite edible boba: characteristics of texture,microstructure, in vitro release behaviour and antioxidant capacity

Konjac glucomannan/sodium alginate composite edible boba (KGM/SA-boba) with good taste is very popular in China, and it is an outstanding carrier for health potential ingredients. In this work, KGM/SA-boba were fortified with 0.25, 0.50, 0.75 and 1.00% purple sweet potato anthocyanin (PSPA), then characterised by the water distribution, texture, microstructure, in vitro release property of PSPA and antioxidant capacity. LF-NMR analysis demonstrated that the free water of KGM/SA-boba could transfer to tightly bound water with the addition of PSPA that made it with better water-binding ability, higher springiness and lower hardness. And the results of SEM and rheology showed that PSPA could stabilise the microstructure of KGM/SA-boba by forming more amorphous regions and hydrogen bonds proved by the results of DSC and FT-IR. Furthermore, 50% of PSPA in PSPA-fortified KGM/SA-boba can be released at the first hour in a simulated gastrointestinal environment. And the scavenging capacity of DPPH and ABTS of the PSPA-fortified KGM/SA-boba after digestion was higher than that of PSPA alone. Generally, PSPA could improve the texture while KGM/SA-boba in turn would make PSPA more stable in the gastrointestinal digestive system.     

火麻仁油微乳凝胶面膜的制备及初步评价

目的:制备火麻仁油微乳凝胶补水面膜并对其理化性质、保湿性和抗氧化活性进行评价.方法:通过伪三元相图确定火麻仁油微乳最佳处方,采用单因素及正交试验优化火麻仁油微乳凝胶处方,载入保湿活性物质制得火麻仁油微乳凝胶面膜并对其质量、稳定性、保湿性和抗氧化活性进行评价.结果:火麻仁油微乳最佳处方:火麻仁油0.2％、PEG-20氢化蓖麻油0.53％、1,3丙二醇0.27％.火麻仁油微乳凝胶最佳处方为卡波姆-940含量1％,丙三醇含量5％,稀释倍数30倍.制得的微乳凝胶澄清透明、涂展性较好、易清洗、不油腻;平均粒径为(30.91±0.31)nm,PDI为0.299±0.017,电位为(-3.54±0.43)mV;黏度为494725.15 mPa·s;pH值为5.50±0.01;保湿效果优于市售某凝胶面膜;火麻仁油微乳凝胶面膜对DPPH自由基清除率高于火麻仁油毛油,质量浓度为6 mg·mL-1时可达62.39％,IC50为3.71 mg·mL-1.结论:火麻仁油微乳凝胶面膜安全、稳定,制备工艺简单,对皮肤具有良好的补水和抗氧化效果,具备开发和推广的价值.     

Densification and joining of a (HfTaZrNbTi)C high-entropy ceramic by hot pressing

A bulk (Hf_0.2Ta_0.2Zr_0.2Nb_0.2Ti_0.2)C high-entropy ceramic (HEC) with a high density was prepared by hot pressing (HP), and through a robust joining technique, large-sized piece was fabricated. A hot-pressed carbide HEC with a single-phase and homogeneous composition was obtained at the sintering temperatures from 1800 to 1950 °C for 30 min under a pressure of 30 MPa. The influence of sintering temperature on the mechanical properties of the HEC was investigated, and the flexural and compressive strengths were reported. Additionally, the feasibility of active brazing of this HEC was studied and solid joints with high shear strength were obtained by atomic diffusion and chemical reaction at the interface, providing a key approach to fabricate complex components of HECs.     

Zinc doped Fe2O3 for boosting Electrocatalytic Nitrogen Fixation to ammonia under mild conditions

Artificial nitrogen fixation is emerging as a promising approach for synthesis of ammonia at mild conditions. Inspired by biological nitrogen fixation based on bacteria containing iron, zinc doped Fe₂O₃ nanoparticles are proposed as an efficient and earth abundant electrocatalyst for converting N₂ to NH₃. In neutral media, it achieves a maximum Faradaic efficiency (FE) of 10.4% and a large NH₃ yield rate of 15.1 μg h^?1 mg^?1_cat. at ?0.5 V vs. reversible hydrogen electrode. This catalyst also exhibits excellent selectivity and stability. Theoretical calculations suggest the reaction follows the associative enzymatic mechanism and it has a barrier of as low as 0.68 eV.     

一种新型井下声波发生装置及其声波传播特性

井下有限空间内声波的有效发生与声能量的高效传递是声波在钻柱中稳定、长距离传输的前提,高效可靠的发生装置是实现井下信息声波传输技术现场化应用的关键。为了实现速度快、准确性高、抗外界因素干扰能力强的井下信息传输,基于超磁致伸缩换能器设计加工了一种井下声波发生装置,并通过建立试验系统,对该装置的功能性及关键参数设计开展了研究。研究结果表明:①带内孔的单级圆锥变幅杆是辐射声波首选,换能器在圆锥变幅杆小端激励的声波辐射进入钻柱中能够获得平面波;②在变幅杆放大系数极小值点附近设计长径比能够有效提高低频段声波能量传递效率;③黄铜材料的声传递介质具有较高的滤波质量与声能量传递效率;④声波能量传递效率随换能器预紧力增加,先增加后保持不变,7.20 kN预紧力能够获得最佳传递效率。结论认为,在井下声波发生与中继装置的设计过程中,应充分考虑换能器声波辐射方式与结构参数对声波能量传递效率的影响;建议进一步研究声发射端机械结构、声载波参数等因素对钻柱中声传播特性的影响,以加快井下信息声传输技术现场应用的步伐。