一种基于抽取LMS的距离旁瓣抑制方法

在噪声雷达中，传统相关处理方法的距离旁瓣受到时宽带宽积的限制，在有限相关处理时间内得到的距离旁瓣较高，会造成微弱目标被强目标、杂波旁瓣淹没的现象。提出一种基于抽取最小均方（Least Mean Square,LMS）滤波的噪声雷达旁瓣抑制方法，将LMS滤波器的系数作为距离压缩结果，从而获取较低的距离旁瓣。对该方法的性能进行了理论分析，并通过数字仿真验证了算法的有效性和理论分析的正确性。     

A review of thin film electrolytes fabricated by physical vapor deposition for solid oxide fuel cells

The ohmic resistance in solid oxide fuel cells (SOFCs) mainly comes from the electrolyte, which can be reduced by developing novel electrolyte materials with higher ionic conductivity and/or fabricating thin-film electrolytes. Among various kinds of thin-film fabrication technology, the physical vapor deposition (PVD) method can reduce the electrolyte thickness to a few micrometers and mitigate the issues associated with high-temperature sintering, which is necessary for wet ceramic methods. This review summarizes recent development progress in thin-film electrolytes fabricated by the PVD method, especially pulsed laser deposition (PLD) and magnetron sputtering. At first, the importance of the substrate surface morphology for the quality of the film is emphasized. After that, the fabrication of thin-film doped-zirconia and doped-ceria electrolytes is presented, then we provide a brief summary of the works on other types of electrolytes prepared by PVD. Finally, we have come to the summary and made perspectives.     

The role of microbial electrogenesis in regulating methane and nitrous oxide emissions from constructed wetland-microbial fuel cell

This study assesses a sustainable solution to greenhouse gases (GHGs) mitigation using constructed wetland-microbial fuel cells (CW-MFC). Roots of wetland plant Acorus Calamus L. are placed in biological anode to better enable anode microorganisms to obtain rhizosphere secretion for power improvement. Three selected cathode materials have a large difference in GHG emissions, and among them, carbon fiber felt (CFF) shows the lowest emissions of methane and nitrous oxide, which are 0.77 ± 0.04 mg/(m²·h) and 130.78 ± 13.08 μg/(m²·h), respectively. The CFF CW-MFC achieves the maximum power density of 2.99 W/m³. As the influent pH value is adjusted from acidic to alkaline, the GHGs emissions are reduced. The addition of Ni inhibits GHGs emission but decreases the electricity, the power density is reduced to 1.09 W/m³, and the methane and nitrous oxide emission fluxes decline to 0.20 ± 0.04 mg/(m²·h) and 15.49 ± 1.86 μg/(m²·h), respectively. Low C/N ratio reduces methane emission, while high C/N ratio effectively inhibits nitrous oxide emission. At the influent pH 8 and C/N = 5:1, the methane emission flux is approximately 10.60 ± 0.27 mg/(m²·h), and the nitrous oxide emission flux is only 10.90 ± 1.10 μg/(m²·h). Based on the above experimental results by controlling variable factors, it is proposed that CW-MFC offers an environment-friendly solution to regulate GHG emissions.     

Effects of injection parameters on propagation patterns of hydrogen-fueled rotating detonation waves

Two-dimensional rotating detonation waves (RDWs) with separate injections of hydrogen and air are simulated using the Navier–Stokes equations together with a detailed chemical mechanism. The effects of injection stagnation temperature and slot width on the detonation propagation patterns are investigated. Results find that extremely high temperatures can lead to a chaotic mode in which detonation waves are generated and extinguished randomly. Increasing the slot width can reduce the number of detonation waves and finally trigger detonation quenching at a low injection stagnation temperature. But increasing the slot width can change the RDW propagation pattern from a chaotic to a stable mode under high injection temperature. Furthermore, the kinetic parameter τ (representing the chemical reactivity of the mixture) and the kinematic parameter α (representing the mixing efficiency of hydrogen and oxygen) are introduced to distinguish the RDW propagation patterns.     

Heterofullerene C48B12-impregnated MOF-5 and IRMOF-10 for hydrogen storage: A combined DFT and GCMC simulations study

The H₂ storage properties of isoreticular metal-organic framework materials (IRMOFs), MOF-5 and IRMOF-10, impregnated with different numbers and types of heterogeneous C₄₈B₁₂ molecules were investigated using density functional theory and grand canonical Monte Carlo (GCMC) calculations. The excess hydrogen adsorption isotherms of IRMOFs at 77 K within 20 bar indicate that suitable number and type of C₄₈B₁₂ molecules play a crucial role in improving the H₂ storage properties of IRMOFs. Among the studied pure and nC₄₈B₁₂ (n = 1, 2, 4, 8) in Ci symmetry impregnating into MOF-5, at 77 K under 6 bar, MOF-5-4C₄₈B₁₂ with a 3.5 wt% and 29.9 g/L hydrogen storage density, and at 77 K under 12 bar, the pure MOF-5 with a 4.9 wt% and 31.0 g/L hydrogen storage density has the best hydrogen storage properties. Whereas, among the studied pure and nC₄₈B₁₂ (n = 1, 2, 4, 8) in S6 symmetry impregnating into IRMOF-10, IRMOF-10-8C₄₈B₁₂ always shows the best hydrogen storage properties among the pure and C₄₈B₁₂-impregnated IRMOF-10 at 77 K within 20 bar. IRMOF-10-8C₄₈B₁₂ has a 6.0 wt% and 34.6 g/L hydrogen storage density at 77 K under 6 bar, and has a 7.1 wt% and 41.4 g/L hydrogen storage density at 77 K under 12 bar. The confinement effect of IRMOFs on C₄₈B₁₂ molecules, and steric hindrance effect of C₄₈B₁₂ molecules on IRMOFs mainly affects the H₂ uptake capacity by comparing the absolute H₂ molecules in individual IRMOFs units, C₄₈B₁₂ molecules, and IRMOFs-nC₄₈B₁₂ compounds. The absolute hydrogen adsorption profiles show that eight C₄₈B₁₂ molecules impregnating into MOF-5 can exert obvious steric effects for H₂ adsorption. The saturated gravimetric and volumetric H₂ densities of IRMOF-10-8C₄₈B₁₂ higher than those of MOF-5-8C₄₈B₁₂ due to with larger free volume.     

子集模拟中马尔可夫链蒙特卡洛抽样算法比较

文章着重研究子集模拟中马尔可夫链蒙特卡洛(MCMC)抽样算法的抽样效率与计算精度。首先，阐述可靠度子集模拟的基本原理与中间状态样本生成的各种MCMC抽样算法，在稳态马尔可夫链构造基础上提出延迟拒绝MMH(Modified Metropolis Hasting)算法，通过在MMH算法上增加备选样本的延迟拒绝步提高MMH算法的抽样效率；阐述基于随机游走与基于扩散方程MCMC方法中建议分布的差异，进一步对备选样本接受率为1的preconditioned Crank-Nicolson(pCN)算法和条件抽样(Conditional sampling, CS)算法开展研究，证明两种算法的等价性；推导有效样本量的计算方法，提出采用有效样本量与总样本量的比值定义MCMC方法的抽样效率。通过复杂目标分布的样本生成研究不同MCMC抽样算法建议分布及其参数对备选样本接受率与抽样效率的影响，最后通过计算实例研究子集模拟过程采用不同MCMC抽样算法得到失效概率的相对误差及其变异性，揭示不同MCMC抽样算法对失效概率计算精度的影响。研究表明：不同MCMC抽样算法生成备选样本的接受率及其自相关性受建议分布及其参数影响较大，对于复杂的目标分布，pCN算法和CS算法的抽样效率较高，延迟拒绝MMH算法次之；采用CS算法和延迟拒绝MMH算法进行子集模拟得到的失效概率精度较高且变异性较低；增加子集模拟中间状态样本量可以提高失效概率计算精度并降低其变异性。     

Cyclic thermal shock resistance for MgAlON–MgO composites obtained with additions of spent MgO–C brick: Microstructure characteristics,thermal shock parameter and thermal shock mechanism

Thermal shock parameters (R, R''', R'''' and R_st) of MgAlON–MgO composites obtained with additions of spent MgO–C brick were calculated using measured mechanical properties and thermal expansion coefficient, determining their resistance to fracture initiation and crack propagation. The cyclic thermal shock experiments of MgAlON–MgO composites performed from 1398 K to ambient temperature indicate that as number of thermal shock cycle increases, retained strength ratio of MgAlON and MgAlON–4.2 wt%MgO sharply decrease and then keep constant, while that of MgAlON–10.5 wt%MgO and MgAlON–15.7 wt%MgO slowly decrease. The reason for the difference is that MgAlON and MgAlON–4.2 wt%MgO show low value of R''' and R'''', and high value of R and R_st. Moreover, precipitation of impurity containing Fe may play a positive role in improvement of thermal shock resistance of MgAlON–MgO composites. MgAlON?4.2 wt%MgO has the maximum retained strength (55 MPa) even after 5 thermal shock cycles, which is expected to be used in the metallurgical industry.     

Enhancement of the radiation resistance of cerium-containing fluorophosphate glasses through codoping with Sb2O3 and Bi2O3

The growing demand for radiation-resistant optical glasses for space and nuclear radiation applications has attracted significant research interest. However, radiation-resistant fluorophosphate glasses have been poorly studied. In this work, we report on the tailoring and performance of radiation-resistant fluorophosphate glasses that contained cerium through codoping with Sb₂O₃ and Bi₂O₃. The physical properties, optical properties, microstructure, and defects of fluorophosphate glasses were investigated using transmittance measurements, absorption measurements, as well as Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electron paramagnetic resonance (EPR) spectroscopy. The results showed that the radiation resistance of all codoped fluorophosphate glasses was better than the undoped cerium-containing fluorophosphate glasses after 10–250 krad(Si) irradiation. Especially in glasses doped with Bi₂O₃, the optical density increment at 385 nm was only 0.1482 after 250 krad(Si) irradiation. The CeO₂ prevented the development of phosphate-related oxygen hole center (POHC) defects, whereas further codoping with Bi₂O₃ suppressed the formation of oxygen hole center (OHC) and POEC defects, reducing the breaking of phosphate chains caused by CeO₂. Bi³⁺ is more likely than Sb³⁺ to change the valence, affecting the transition equilibrium of intrinsic defects and reducing the concentration of defects produced by irradiation. When codoping with Sb₂O₃ and Bi₂O₃, Bi₂O₃ does not enhance radiation resistance owing to the scission effect of Sb₂O₃ on the phosphate chain, which is not conducive to the radiation resistance of glasses. This indicates that the cerium-containing fluorophosphate glasses doped with Bi₂O₃ can effectively suppress the defects caused by irradiation and improve the radiation resistance of the glasses.     

Preparation,microstructure and ion-irradiation damage behavior of Al4SiC4-added SiC ceramics

Single-phase Al₄SiC₄ powder with a low neutron absorption cross section was synthesized and mixed with SiC powder to fabricate highly densified SiC ceramics by hot pressing. The densification of SiC ceramics was greatly improved by the decomposition of Al₄SiC₄ and the formation of aluminosilicate liquid phase during the sintering process. The resulting SiC ceramics were composed of fine equiaxed grains with an average grain size of 2.0 μm and exhibited excellent mechanical properties in terms of a high flexure strength of 593 ± 55 MPa and a fracture toughness of 6.9 ± 0.2 MPa m^1/2. Furthermore, the ion-irradiation damage in SiC ceramics was investigated by irradiating with 1.2 MeV Si⁵⁺ ions at 650 °C using a fluence of 1.1 × 10¹⁶ ions/cm², which corresponds to 6.3 displacements per atom (dpa). The evolution of the microstructure was investigated by X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. The breaking of Si–C bonds and the segregation of C elements on the irradiated surface was revealed by XPS, whereas the formation of Si–Si and C–C homonuclear bonds within the Si–C network of SiC grains was detected by Raman spectroscopy.     

Mg gas infiltration for the fabrication of MgB2 pellets using nanosized and microsized B powders

MgB₂ superconductor pellets were synthesized through Mg gas infiltration method using nanosized- and microsized B powders. There was a marked difference in the superconducting properties of the two samples, particularly in the pinning force and dominant pinning mechanism. The microstructures of the samples were observed using HR-TEM and STEM-HAADF, and the results showed that the primary reason for the difference in the superconducting properties is the distribution of the nanosized second-phase particle MgO. Additionally, a feasible reaction model for the Mg gas infiltration method was established. Compared to the Mg liquid infiltration method, the gas infiltration showed better penetrability ability with a small amount of residual Mg. This study presents a novel synthesis process to fabricate an MgB₂ pellet with superior density and superconducting properties. This method can be used in multiple applications such as superconducting bearings, compact superconductor magnets, and magnetic shielding.