Dynamic analysis of tapping mode atomic force microscope (AFM) for critical dimension measurement

Transient dynamics of tapping mode atomic force microscope (AFM) for critical dimension measurement are analyzed. A simplified nonlinear model of AFM is presented to describe the forced vibration of the micro cantilever-tip system with consideration of both contact and non-contact transient behavior for critical dimension measurement. The governing motion equations of the AFM cantilever system are derived from the developed model. Based on the established dynamic model, motion state of the AFM cantilever system is calculated utilizing the method of averaging with the form of slow flow equations. Further analytical solutions are obtained to reveal the effects of critical parameters on the system dynamic performance. In addition, features of dynamic response of tapping mode AFM in critical dimension measurement are studied, where the effects of equivalent contact stiffness, quality factor and resonance frequency of cantilever on the system dynamic behavior are investigated. Contact behavior between the tip and sample is also analyzed and the frequency drift in contact phase is further explored. Influence of the interaction between the tip and sample on the subsequent non-contact phase is studied with regard to different parameters. The dependence of the minimum amplitude of tip displacement and maximum phase difference on the equivalent contact stiffness, quality factor and resonance frequency are investigated. This study brings further insights into the dynamic characteristics of tapping mode AFM for critical dimension measurement, and thus provides guidelines for the high fidelity tapping mode AFM scanning.     

Preparation and properties of modified graphene oxide incorporated waterborne polyurethane acrylate

In this study, a new modifier (KPG) was prepared by modifying graphene oxide with γ‐glycidoxypropyl trimethoxysilane (KH560) and polydimethylsiloxane (PDMS). KPG was in turn added to aqueous urethane acrylate for the fabrication of waterborne polyurethane polyacrylate emulsion modified with KH560‐PDMS composite (KPG/WPUA). Textural characterizations of the KPG/WPUA coating were achieved via Fourier transform infrared, SEM, TGA and AFM techniques, which revealed that the KPG/WPUA film possessed a smooth surface. The synthesized KPG/WPUA films were tested for mechanical properties, hydrophobicity and acid/water corrosion performance which suggested their highly hydrophobic surface. KPG/WPUA with 0.1% KPG showed a contact angle of 118.35°, 30.35° higher than that of pristine WPUA. The KPG/WPUA film exhibited higher thermal stability, i.e. a 5% weight loss temperature of 305 °C, which was 30 °C higher than that of pristine WPUA film. The Young's modulus and elongation at break of the KPG/WPUA film were 34.1 MPa and 74.88% respectively, which were higher than that of WPUA film. Furthermore, KPG/WPUA films exhibited greater resistance (without obvious blistering and the white spotting phenomenon) to H₂O₂, HCl and water corrosion than pristine WPUA. The superior performance of KPG/WPUA films was attributed to the network chain structure formed upon the introduction of KPG into WPUA. The outstanding performance of KPG/WPUA films in terms of mechanical properties, thermal stability and high resistance to acidic and water corrosion makes them interesting alternative contenders for target applications. © 2019 Society of Chemical Industry     

Work function difference of naphthyl end-capped oligothiophene in different crystal alignments studied by Kelvin probe force microscopy

The performance of organic semiconductor devices is strongly affected by the interface energetics at the junctions between the constituent materials. A large group of organic semiconductors consists of rodlike small molecules that crystallize upon deposition with a molecular orientation dependent on the specifics of the molecule–molecule and molecule–substrate interactions. By means of Kelvin probe force microscopy (KPFM), this work studies naphthyl end-capped oligothiophene, 5,50-bis(naphth-2-yl)-2,20-bithiophene (NaT2), deposited on samples of pristine ${\text{SiO}}_2$ and samples of graphene-covered ${\text{SiO}}_2$. The crystal molecular orientation of NaT2 is dependent on the substrate on which it is deposited. On ${\text{SiO}}_2$, the NaT2 molecules are predominately upright standing, forming crystallites with distinct terrace heights of $2.0\pm 0.1\text{nm}$. Measurements indicate formation of an initial wetting layer in the NaT2-${\text{SiO}}_2$ system for the upright standing molecules. When deposited on graphene, the molecules additionally form fibrous structures with heights of $10-115\text{nm}$ consisting of molecules lying down (face-on orientation). Using KPFM, a difference in the local contact potential difference (CPD) of upright standing NaT2 and face-on oriented structures on graphene is measured to be $-0.16\pm 0.04\text{V}$, indicating a work function difference between the two system configurations, which is confirmed through Density Functional Theory calculations.     

Alpha Synuclein only Forms Fibrils In Vitro when Larger than its Critical Size of 70 Monomers

The aggregation of α-synuclein into small soluble aggregates and then fibrils is important in the development and spreading of aggregates through the brain in Parkinson's disease. Fibrillar aggregates can grow by monomer addition and then break into fragments that could spread into neighboring cells. The rate constants for fibril elongation and fragmentation have been measured but it is not known how large an aggregate needs to be before fibril formation is thermodynamically favorable. This critical size is an important parameter controlling at what stage in an aggregation reaction fibrils can form and replicate. We determined this value to be approximately 70 monomers using super-resolution and atomic force microscopy imaging of individual α-synuclein aggregates formed in solution over long time periods. This represents the minimum size for a stable α-synuclein fibril and we hypothesis the formation of aggregates of this size in a cell represents a tipping point at which rapid replication occurs.     

A role of sea buckthorn on Alzheimer’s disease

Evidence suggests that diets rich in antioxidants reduce the risk factors of Alzheimer’s disease (AD). Hippophae rhamnoides, commonly known as sea buckthorn (SB), is rich in antioxidants which could have direct effects on amyloid-beta (Aβ) levels and consequently influence AD pathogenesis. In this study, sea buckthorn powder (SBP) was administered at varying concentrations (0.6, 0.9, 1.2, 1.5 and 1.8 µg mL⁻¹) to cell cultures (BE(2)-M17) with 20 mm Aβ for 72 h. MTS test indicated that SB significantly increased cell viability in Aβ-induced cells up to 95%. Results of Western blot showed maximum 38% inhibition of Aβ compared to the control (Aβ only). ELISA demonstrated significantly lower amyloid-β level (6672 pg mL⁻¹) than the control (10189 pg mL⁻¹). Images of AFM further confirmed the presence of low quantity of amyloid beta in SBP-treated cells. These findings suggest that SB warrants further investigation as potential therapeutic agent in the treatment of AD.     

Composites prepared from polyurethanes modified with silicone-acrylic nanopowders

Linear polyurethanes were obtained the reaction of 1,6-hexamethylene diisocyanate with poly(ɛ-caprolactone)diol and butane-1,4-diol. Synthesis was carried out in the presence of 1, 3 and 5 wt.% of polydimethylsiloxane-poly(methyl methacrylate) core–shell nanopowder. Solutions of resulting polyurethanes were cast on PTFE plates and dried at 140 °C to form films. The presence of structures originating from modifier was confirmed by IR and XPS spectroscopy. DSC analysis revealed the presence of crystalline phase in all samples. Contact angles were determined using standard fluids and surface free energy parameters were calculated. The results of these investigations proved that modification with silicone-acrylic nanopowder resulted in significant increase in hydrophobicity of polyurethane surfaces Changes in surface characteristics were also reflected in surface images obtained in AFM studies. It is suggested that the polyurethane composites obtained in this study can be tested as coatings for biomedical applications.     

Improved direct inverse tracking control of a piezoelectric tube scanner for high-speed AFM imaging

For a piezoelectric tube scanner (PTS), this paper proposes an improved direct inverse tracking control algorithm and apply it to an atomic force microscope (AFM) to accomplish high-speed scanning tasks. That is, to enhance the high-speed tracking control performance of a PTS, an improved direct inverse rate-dependent Prandtl–Ishlinskii (P–I) model is firstly constructed, which includes a polynomial module to eliminate the structure nonlinearity. Based on the model, a practical feedforward control law is then designed to implement high-speed tracking control for a high-frequency trajectory with strong robustness, which presents the advantages of high-speed response, simple structure and convenient implementation. Subsequently, the designed feedforward law is combined with a feedback component, and the combined control strategy is employed in an AFM to accomplish fast imaging tasks. Numerous experimental results are then collected, which convincingly demonstrate the superior performance of the proposed practical model/control scheme.     

Self-Assembly and Neurotoxicity of β-Amyloid (21–40) Peptide Fragment: The Regulatory Role of GxxxG Motifs

The three GxxxG repeating motifs from the C-terminal region of β-amyloid (Aβ) peptide play a significant role in regulating the aggregation kinetics of the peptide. Mutation of these glycine residues to leucine greatly accelerates the fibrillation process but generates a varied toxicity profile. Using an array of biophysical techniques, we demonstrated the uniqueness of the composite glycine residues in these structural repeats. We used solvent relaxation NMR spectroscopy to investigate the role played by the surrounding water molecules in determining the corresponding aggregation pathway. Notably, the conformational changes induced by Gly³³ and Gly³⁷ mutations result in significantly decreased toxicity in a neuronal cell line. Our results indicate that G³³xxxG³⁷ is the primary motif responsible for Aβ neurotoxicity, hence providing a direct structure–function correlation. Targeting this motif, therefore, can be a promising strategy to prevent neuronal cell death associated with Alzheimer's and other related diseases, such as type II diabetes and Parkinson's.     

Low energy oblique ion beam sputtering induced surface engineering of polyethylene terephthalate

ABSTRACT

In the present work, the self-organized pattern formation with simultaneous surface smoothing of Polyethylene terephthalate (PET) by 40 keV Ar+ ions irradiation has been discussed. The effect of most important experimental parameter i.e. ion beam incidence that control these processes has been discussed by varying off normal incidences from 30⁰ to 50⁰. The changes in surface topography have been studied using Atomic Force Microscopy (AFM). It has been investigated from AFM analysis that oblique ion beam induced sputtering significantly reduced the surface roughness with simultaneous formation of some hillock and hole like structures.