地应力条件下的凿岩爆破数值模拟

为了研究地应力对凿岩爆破的影响,采用DDA方法模拟爆炸应力波作用下考虑地应力条件时的单孔和多孔凿岩爆破破岩过程。模拟发现,随着初始地应力水平的增加,裂纹扩展半径和破岩区域面积减小,裂纹发育主方向趋于地应力的最大主应力方向,初始地应力对裂纹的抑制和引导作用明显;初始地应力水平的增加,对拉伸裂纹的抑制作用更为显著,从而降低了拉伸破坏对爆破破岩的贡献。模拟也表明,在初始地应力存在的条件下,通过对爆破载荷和炮孔布置进行针对性的优化,可以克服地应力带来的影响,并取得预期的爆破效果。本研究对地应力条件下的凿岩爆破工程具有理论和参考意义。     

Total Site Hydrogen Integration with fresh hydrogen of multiple quality and waste hydrogen recovery in refineries

This paper proposes a novel method combining Pinch Methodology and waste hydrogen recovery, aiming to minimise fresh hydrogen consumption and waste hydrogen discharge. The method of multiple-level resource Pinch Analysis is extended to the level of Total Site Hydrogen Integration by considering fresh hydrogen sources with various quality. Waste hydrogen after Total Site Integration is further regenerated. The technical feasibility and economy of the various purification approaches are considered, demonstrated with a case study of a refinery hydrogen network in a petrochemical industrial park. The results showed that fresh hydrogen usage and waste hydrogen discharge could be reduced by 21.3% and 67.6%. The hydrogen recovery ratio is 95.2%. It has significant economic benefits and a short payback period for Total Site Hydrogen Integration with waste hydrogen purification. The proposed method facilitates the reuse of waste hydrogen before the purification process that incurs an additional environmental footprint. In line with the Circular Economy principles, hydrogen resource is retained in the system as long as possible before discharge.     

Optimization of hydrogen enrichment via palladium membrane in vacuum environments using Taguchi method and normalized regression analysis

In this study, the separation of hydrogen from gas mixtures using a palladium membrane coupled with a vacuum environment on the permeate side was studied experimentally. The gas mixtures composed of H₂, N₂, and CO₂ were used as the feed. Hydrogen permeation fluxes were measured with membrane operating temperature in the range of 320–380 °C, pressures on the retentate side in the range of 2–5 atm, and vacuum pressures on the permeate side in the range of 15–51 kPa. The Taguchi method was used to design the operating conditions for the experiments based on an orthogonal array. Using the measured H₂ permeation fluxes from the Taguchi approach, the stepwise regression analysis was also employed for establishing the prediction models of H₂ permeation flux, followed by the analysis of variance (ANOVA) to identify the significance and suitability of operating conditions. Based on both the Taguchi approach and ANOVA, the H₂ permeation flux was mostly affected by the gas mixture composition, followed by the retentate side pressure, the vacuum degree, and the membrane temperature. The predicted optimal operating conditions were the gas mixture with 75% H₂ and 25% N₂, the membrane temperature of 320 °C, the retentate side pressure of 5 atm, and the vacuum degree of 51 kPa. Under these conditions, the H₂ permeation flux was 0.185 mol s^?1 m^?2. A second-order normalized regression model with a relative error of less than 7% was obtained based on the measured H₂ permeation flux.     

Meta-Analysis of Methamphetamine Modulation on Amyloid Precursor Protein through HMGB1 in Alzheimer’s Disease

The deposition of amyloid-beta (Aβ) through the cleavage of amyloid-beta precursor protein (APP) is a biomarker of Alzheimer’s disease (AD). This study used QIAGEN Ingenuity Pathway Analysis (IPA) to conduct meta-analysis on the molecular mechanisms by which methamphetamine (METH) impacts AD through modulating the expression of APP. All the molecules affected by METH and APP were collected from the QIAGEN Knowledge Base (QKB); 78 overlapping molecules were identified. Upon simulation of METH exposure using the “Molecule Activity Predictor” feature, eight molecules were found to be affected by METH and exhibited activation relationships on APP expression at a confidence of p = 0.000453 (Z-score = 3.51, two-tailed). Core Analysis of these eight molecules identified High Mobility Group Box protein 1 (HMGB1) signaling pathway among the top 5 canonical pathways with most overlap with the 8-molecule dataset. Simulated METH exposure increased APP expression through HMGB1 at a confidence of p < 0.00001 (Z-score = 7.64, two-tailed). HMGB1 is a pathogenic hallmark in AD progression. It not only increases the production of inflammatory mediators, but also mediates the disruption of the blood-brain barrier. Our analyses suggest the involvement of HMGB1 signaling pathway in METH-induced modulation of APP as a potential casual factor of AD.     

Notwendigkeit und Vermarktung von Flexibilitätsoptionen im Energiesystem der Zukunft

Demands on production, distribution and consumption of electrical energy change fundamentally with the energy revolution. Energy purchasing costs for inflexible consumers are rising and proceeds of inflexible producers are sinking. Companies are able to reduce costs by marketing operational flexibility options. This article sets out the need of flexibility in the energy system and the new marketing options. Flexibility potentials within infrastructure plants of a chemical park are analyzed, evaluated regarding marketing and activated in the presented research project FlexChemistry.     

Evaluation of dynamic modulus measurement for C/C-SiC composites at different temperatures

The determination of elastic properties at application temperature is fundamental for the design of fibre reinforced ceramic composite components. An attractive method to characterize the flexural modulus at room and high temperature under specific atmosphere is the nondestructive Resonant Frequency Damping Analysis (RFDA). The objective of this paper was to evaluate and validate the modulus measurement via RFDA for orthotropic C/C-SiC composites at the application temperature. At room temperature flexural moduli of C/C-SiC with 0/90° reinforcement were measured under quasi-static 4-point bending loads and compared with dynamic moduli measured via RFDA longitudinally to fibre direction. The dynamic modulus of C/C-SiC was then measured via RFDA up to 1250°C under flowing inert gas and showed an increase with temperature which fitted with literature values. The measured fundamental frequencies were finally compared to those resulting from numerical modal analyses. Dynamic and quasi-static flexural moduli are comparable and the numerical analyses proved that bending modes are correctly modeled by means of dynamic modulus measured via RFDA. The nondestructive RFDA as well as the numerical modeling approach are suitable for evaluation of C/C-SiC and may be transferred to other fibre reinforced ceramic composite materials.     

Ontology-based approach for the provision of simulation knowledge acquired by Data and Text Mining processes

Numerical simulation techniques such as Finite Element Analyses are essential in today's engineering design practices. However, comprehensive knowledge is required for the setup of reliable simulations to verify strength and further product properties. Due to limited capacities, design-accompanying simulations are performed too rarely by experienced simulation engineers. Therefore, product models are not sufficiently verified or the simulations lead to wrong design decisions, if they are applied by less experienced users. This results in belated redesigns of already detailed product models and to highly cost- and time-intensive iterations in product development.Thus, in order to support less experienced simulation users in setting up reliable Finite Element Analyses, a novel ontology-based approach is presented. The knowledge management tools developed on the basis of this approach allow an automated acquisition and target-oriented provision of necessary simulation knowledge. This knowledge is acquired from existing simulation models and text-based documentations from previous product developments by Text and Data Mining. By offering support to less experienced simulation users, the presented approach may finally lead to a more efficient and extensive application of reliable FEA in product development.     

《电子显微分析》课程教学内容及方法研究

《电子显微分析》课程是目前高校材料类和生命科学类专业一门重要的专业选修课。根据《电子显微分析》课程特点，剖析了该课程的教学现状以及存在的问题。针对这些问题，在教学内容的设定、教学方式的调整及实践性教学的考核等方面做了一些思考。     

Possible origin of ferromagnetism in antiferromagnetic orthorhombic-YFeO3: A first-principles study

Rare-earth orthoferrites (RFeO₃) are well-known for the antiferromagnetic ground state. However, some of the recent experimental results suggest that the few members of RFeO₃ family possess ferromagnetism. In the present investigation we report the possible origin of ferromagnetism in antiferromagnetic YFeO₃ using density functional theory. For this purpose, we have considered pure as well as self-doping in YFeO₃ i.e. by considering the point defect at Y, Fe and O sites. Our finding suggests that the point defects in YFeO₃ results in the mixed-valence state of Fe, which may result in ferromagnetism through Zener double exchange mechanism.     

Comparison of OWAS,RULA and REBA for assessing potential work-related musculoskeletal disorders

This study compared three representative observational methods for assessing musculoskeletal loadings: Ovako Working Posture Analysis System (OWAS), Rapid Upper Limb Assessment (RULA), and Rapid Entire Body Assessment (REBA). The comparison was based on 209 cases of upper-body musculoskeletal disorders (MSDs) diagnosed by medical doctors. The most awkward/stressful posture in each participant's tasks was assessed using these techniques. Postural loadings were rated more highly by the RULA than by the OWAS and REBA (p < 0.01). The chi-square test and logistic regression analysis showed that only RULA grand score and action level, and REBA action level were associated with MSD work-relatedness (p < 0.01, p < 0.05, and p < 0.05, respectively). The percentage concordant values of the logistic model for the RULA grand score and action level were 52.4% and 44.8%, respectively, while the percentage concordant value for the REBA action level was 22.1%. Therefore, the RULA may be the best system for estimating the postural loads and work-relatedness of MSDs.Relevance to industryWork-related musculoskeletal disorders are the leading cause of workplace disability in the developed countries. For preventing the disorders, quantification of musculoskeletal loads is required.