Real-Time analysis of exosome secretion of single cells with single molecule imaging

The exosome-mediated response can promote or restrain the diseases by regulating the intracellular pathways, making the exosome become an effective marker for diagnosis and therapeutic control at the single-cell level. However, real-time analysis is hard to be achieved with traditional approaches because the exosomes usually need to be enriched by ultracentrifugation for a measurable signal-to-noise ratio. Recently developed label-free single-molecule imaging approaches may become an real-time quantitative tool for the analysis of single exosomes and related secretion behaviors of single living cells owing to their extreme sensitivity.     

Susceptor-assisted fast microwave sintering of TiN reinforced SiAlON composites in a single mode cavity

In the present study, 17 wt % TiN reinforced α-β SiAlON composites were sintered at low temperature by susceptor-assisted microwave heating. The effect of TiN addition on dielectrical properties of starting powders, as well as the influence of sintering temperature on phase evolution, microstructure development and mechanical properties of α/β-SiAlON-TiN composites were investigated. The obtained results showed that TiN addition increased the microwave absorbing properties which is reflected in the peak sintering temperature. Thus, the α:β ratio decreased and mechanical properties were improved, especially the fracture toughness of the composites. Furthermore, an estimate of energy consumption during microwave assisted sintering at the laboratory scale is presented. As a result, the highest values for relative density (97.1%), Vickers hardness (13.35 ± 0.47 GPa), and fracture toughness (7.52 ± 0.54 MPa m^1/2) were obtained by microwave sintering for 30 min at 1300 °C.     

Tropfenbewegung und Stofftransport in technischen Flüssig/flüssig-Systemen. Teil 2: Auswirkung von Grenzflächeneffekten und Verunreinigungen

The design of a liquid/liquid contact apparatus necessitates the knowledge of fluid dynamics and mass transfer in the dispersion. Prediction of process parameters is challenging due to swarm and interfacial effects. Single drop investigations are suitable to enable a sophisticated dimensioning based on few simple experiments combined with published theories and correlations. In the first part of this article, the fundamentals of fluid dynamics and mass transfer in absence of interfacial effects were explained. Here, an overview of relevant interfacial phenomena and the influence of different substances typically occurring in technical applications as impurities or accompanying components is given.     

Advances in solid-state fiber batteries for wearable bioelectronics

Powering wearable bioelectronics with decent skin conformability and wearing comfort is highly desired. Fiber batteries could provide an attractive alternative to traditional rigid ones and present a compelling solution to this problem. In this review, we will discuss the various classes of fiber batteries, including lithium batteries, zinc batteries, and other types of fiber batteries. We will then report the latest research progress on each battery category through its working mechanism, materials usage, structure design, and wearable applications. Finally, we provide insights into current challenges and future applications of fiber batteries, aiming to promote the development of low-cost and high-performance fiber battery technologies for wearable bioelectronics.     

A numerical study of dynamic behaviors of a unitized regenerative fuel cell during gas purging

The gas purging states affect electricity output and energy storage capacity of unitized regenerative fuel cells. In this study, a model of unitized regenerative fuel cell is established. Cell voltages and operating temperatures influences on the dynamic distribution of thermal fluid during purging process and the discharge of residual liquid water in electrolytic cell mode are investigated. The motivation of the present study is better understanding the gas purging characteristics and its effect on reaction behaviors of unitized regenerative fuel cells. Simulation results reveal a significant influence of purging gas temperature on the water flooding and a great effect of operating voltage on the water diffusion. The operating temperature of electrolytic cell model almost has little effect on purging results at different cell temperature and the same purging gas temperature. When the purging gas temperature is changed, higher temperatures of cell and purging gas facilitate liquid water discharging out from the cell regions. In cell water flooding situation, when having large liquid content, the purging gas has little effects on the water expelling process.     

Utilization of pyrolytic oil and hydrogen enriched syngas from single feedstock (delonix regia) through pyrolysis process and its influence on performance and emission characteristics in CI engine

The main objective of the present investigation is to conduct the performance, combustion and emission analysis of CI engine operated using hydrogen enriched syngas (pyrolytic gas) and biodiesel (pyrolytic oil) as dual fuel mode condition. Both the pyrolytic oil and syngas is obtained from single feedstock delonix regia fruit pod through pyrolysis process and then pyrolytic oil is converted into biodiesel through esterification. Initially biomass is subjected to thermal degradation at various pyrolysis temperature ranges like 350–600 °C. During the pyrolysis process syngas, pyrolytic oil and char are produced. The syngas is directly used in the CI engine and pyrolytic oil is converted into biodiesel and then used in the CI engine. The pyrolytic oil and syngas is subjected to FTIR and GC/TCD analysis respectively. The syngas analysis confirms the presence of various gases like H₂, CH₄, CO₂, CO and C₂H₄ in different proportions. The various proportions of the syngas is mainly depending upon the reactor temperature and moisture content in the biomass. The syngas composition varies with increase in the temperature and at 400 °C, higher amount of hydrogen is present and its composition are H₂ 28.2%, CO is 21.9%, CH₄ is 39.1% and other gases in smaller amounts. The biodiesel of B20 and syngas of 8lpm produced from the same feedstock are considered as test sample fuels in the CI engine under dual fuel mode operation to study the performance and emission characteristics. The study reveals that BTE has slight increase than diesel of 1.5% at maximum load. On the another hand emission like CO, HC and smoke are reduced by 15%,25% and 32% respectively at full load condition, whereas NO_x emission is increased at all loads in the range of 10–15%. Therefore B20+syngas of 8lpm can be used as an alternative fuel in CI engine without any modification and major products from pyrolysis process with waste biomass is fully used as fuel in the CI engine.     

Prediction of mode I fracture toughness of rock using linear multiple regression and gene expression programming

Prediction of mode I fracture toughness (K_IC) of rock is of significant importance in rock engineering analyses. In this study, linear multiple regression (LMR) and gene expression programming (GEP) methods were used to provide a reliable relationship to determine mode I fracture toughness of rock. The presented model was developed based on 60 datasets taken from the previous literature. To predict fracture parameters, three mechanical parameters of rock mass including uniaxial compressive strength (UCS), Brazilian tensile strength (BTS), and elastic modulus (E) have been selected as the input parameters. A cluster of data was collected and divided into two random groups of training and testing datasets. Then, different statistical linear and artificial intelligence based nonlinear analyses were conducted on the training data to provide a reliable prediction model of K_IC. These two predictive methods were then evaluated based on the testing data. To evaluate the efficiency of the proposed models for predicting the mode I fracture toughness of rock, various statistical indices including coefficient of determination (R²), root mean square error (RMSE), and mean absolute error (MAE) were utilized herein. In the case of testing datasets, the values of R², RMSE, and MAE for the GEP model were 0.87, 0.188, and 0.156, respectively, while they were 0.74, 0.473, and 0.223, respectively, for the LMR model. The results indicated that the selected GEP model delivered superior performance with a higher R² value and lower errors.     

Influence of bio-clogging on permeability characteristics of soil

It is necessary to enhance the barrier performance of cutoff walls in order to improve the contamination control level, especially for reconstruction or expansion of existing landfill sites. This paper presents a comprehensive laboratory investigation on the synergistic effects of microorganisms and fibers on the hydraulic conductivity of silty sand to evaluate the applicability to the field condition as an alterative barrier material. Inside the soil, the added carbon fibers not only provided good biocompatibility, but also formed spatial three-dimensional network between soil particles to improve the bacterial adhesion that eventually caused 2–3 orders of magnitude decrease in soil permeability. The resistance of the biofilm to extreme conditions was tested by permeation with solutions of different salinity and pH values, and by subjecting specimens to various hydraulic gradients and soil conditions. Despite the microbial growth inhibition occurred at these conditions, however, biofilm can largely remain intact and continue to reduce k, which due to the gradual adaptation of microorganisms to the extreme environment and the gradual recovery of their activity. Results of these tests demonstrate that biofilm treatment may be a feasible technology for creating waste containment barriers in soil.     

定子分段式永磁直线同步电机速度波动抑制方法研究

为了解决定子分段式永磁直线同步电机(PMLSM)存在的因磁阻效应、负载阻力、摩擦力、参数摄动以及动子进出定子时耦合面积变化所造成的控制性能下降的难题,根据动子和定子的耦合状态,提出一种在完全耦合阶段和动子退出定子阶段的分段式控制方法。首先,在动子与定子完全耦合阶段采用改进滑模控制器减小推力波动导致的速度波动,再通过加入扰动观测器降低滑模切换项所带来的抖振现象;在动子退出定子阶段,建立相关电磁参数与动子位置的函数关系,实时补偿由耦合面积变化引起的动子失速,使动子速度在退出时接近给定值。仿真及实验结果表明动定子完全耦合过程中的速度稳态误差为0.005 m/s,收敛时间为0.3 s,动子退出定子阶段的速度波动不超过0.04 m/s,满足定子分段式PMLSM用于长行程自动运输系统对平稳性及快速性的需求。     

贾燕1,赵永涛2,张红松2

为确定ZrO2/莫来石热障涂层的单层最佳厚度,采用有限元技术研究单层厚度对ZrO2/莫来石热障涂层热冲击应力的影响。结果表明,莫来石层厚度为0.25mm时,涂层表面及ZrO2/莫来石界面处具有最大热应力,而其它莫来石层厚度时涂层内部热应力则受莫来石层厚度影响不明显。当ZrO2层厚度为0.3mm时,ZrO2/莫来石涂层中的热应力在整个横向距离范围内保持稳定,而其它情况下涂层中的热应力则与ZrO2层厚度成正比。涂层表面处的径向热应力大于ZrO2/莫来石界面处的对应值。