辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响

研究辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响。采用3种不同上辊/下辊转速比(ω/ω0,ω为上辊转速,ω0为下辊转速)1:1、1:1.2及1:1.4进行多次试验。结果显示,在最大辊速差条件下(ω/ω0=1:1.4),7075铝板在轧制方向的屈服强度和极限抗拉强度分别提高41.5%和21.9%。此外,当辊速比ω/ω0为1:1.4时,成品轧制板的平均晶粒尺寸减小36%,横剖面平均硬度增加约9.2%。织构研究结果显示,辊速差越大,成品各向同性及硬度越大。然而,采用不同辊速度的连铸连轧会导致变形板伸长率降低约6%。     

Anisotropy Effects in the Shape-Memory Performance of Polymer Foams

Isotropic and anisotropic shape-memory polymer foams are prepared by supercritical carbon dioxide foaming from a multiblock copolymer (PDLCL) consisting of poly(ω-pentadecalactone) and poly(ε-caprolactone) segments. Analysis by micro-computed tomography reveals for the anisotropic PDLCL foam cells a high shape anisotropy ratio of R = 1.72 ± 0.62 with a corresponding Young's compression moduli ratio between longitudinal and transversal direction of 4.3. The experimental compression data in the linear elastic range can be well described by the anisotropic open foam model of Gibson and Ashby. A micro-morphological analysis for single pores using scanning electron microscopy images permits the correlation between the macroscopic stress-compression behavior and microscale structural changes.     

单晶硅表层机械力学特性的各向异性分析

为探究挠性筋结构单晶硅材料的各向异性特性以及KOH腐蚀工艺对其力学性能的影响规律,进行纳米压痕实验,并结合原子力显微镜观察单晶硅表层3个主晶面上压痕裂纹形貌随晶向的变化规律,分析单晶硅材料表层弹性模量、硬度、断裂韧性等机械力学特性参数在(001)、(110)及(111)3个主要晶面上沿各个晶向的变化规律;分析挠性筋结构单晶硅材料(001)晶面的KOH腐蚀工艺对其材料表面机械特性的影响规律.结果表明:挠性筋单晶硅在(001)晶面上弹性模量的各向异性变化幅度明显,硬度及断裂韧性各向异性的变化幅度不大;挠性筋单晶硅在(110)晶面弹性模量和断裂韧性的各向异性变化幅度明显,硬度各向异性变化幅度不大;挠性筋单晶硅在(111)晶面硬度值、弹性模量及断裂韧性参数的变化幅度幅值均较小;确定了单晶硅表层3个晶面裂纹最易扩展的晶向方向,KOH腐蚀工艺使得单晶硅表面质量降低,腐蚀后暴露的表面微裂纹、缺陷等会使得单晶硅(001)晶面表层硬度、断裂韧性降低,从而降低了挠性筋结构的实际断裂强度.     

Correlation among hydrogenation,magnetoelastic coupling,magnetic anisotropy,and magnetoresistance in magnetostrictive,hydrogen-absorbing palladium-cobalt alloy films for hydrogen sensing

Hydrogen-absorbing magnetic alloy films, such as palladium-cobalt (PdCo) alloy films, are expected to play a significant role in the next generation of hydrogen sensors. However, effects of hydrogenation on such films are very complex, since these alloys show strong spin-orbit interaction, i.e., strong magnetoelastic coupling. Accordingly, we conducted integrated research on the hydrogenation, magnetoelastic coupling, magnetism, and galvanomagnetic effect of PdCo alloy films having different magnetic anisotropies of longitudinal and perpendicular magnetic anisotropies. As a result, it was revealed that the stress in the film determines its magnetic anisotropy. The magnetoresistance curves of films, consisting of ordinal and anisotropic magnetoresistance effects, correspond well to the magnetization-magnetic field curves. Hydrogenation results in the compressive stress and decreased magnetostriction, which both have a negative influence on the perpendicular magnetic anisotropy energy of the films. Moreover, the influence is observed also in ordinal and anisotropic magnetoresistances. In addition, the increases in coercivity and electronic resistivity due to the incorporated hydrogen atoms (and related defects) are detected. The results are summarized in a correlation diagram, which shows that hydrogen-absorbing magnetic alloy films are very suitable for use in hydrogen sensors—the films can detect hydrogen via various methods such as magnetic anisotropy, galvanomagnetic effect, coercivity, and resistivity.     

Characterization of anisotropic gas permeability and thermomechanical properties of highly textured porous alumina

Porous alumina with a highly textured microstructure was fabricated by pulse electric current sintering (PECS) using alumina platelets. Highly oriented porous alumina with a porosity of 3%–50% was obtained by a pressure-controlled method of PECS. The properties of the highly textured porous alumina were measured in two directions. The nitrogen gas permeance and thermal conductivity at room temperature were higher in the direction along the platelet length due to the higher continuity of pores and the connectivity of alumina platelets, respectively. The anisotropy of the thermal conductivity at room temperature was investigated and explained by the effect of grain size of platelets as well as morphology and orientation of pores. The bending strength was higher with the loading direction along the platelet thickness. The thermal shock strength was clearly different in the two directions. The difference in the thermal shock strength was investigated by the measurement of properties and thermal stress analysis.     

Deposition-environment-dependent structural and magnetic property modification of [111]-oriented epitaxial CoFe2O4 films

We examined the magnetic, structural, and chemical properties of CoFe₂O₄ films deposited on Al₂O₃ substrates using RF-magnetron sputtering under Ar and Ar + O₂ environments. Perpendicular magnetic anisotropy with large magnetization was observed in the case of the film deposited under the Ar + O₂ environment. However, no significant anisotropy appeared in the film deposited under the Ar environment. Interestingly, depth-dependent X-ray photoelectron spectra showed nearly identical stoichiometric ratios of Co/Fe and oxygen vacancies regardless of the deposition environment. Structurally, high-quality crystallinity with in-plane compressive strain, and lower surface and interfacial roughness were induced in the film deposited under the Ar + O₂ environment. Cross-sectional transmission electron microscopy and X-ray reflectivity measurements showed that oxygen not only suppressed the deposition rate but also increased the electron density of the film, resulting in better crystallinity. Hence, the presence of oxygen during deposition should be considered as one of the essential parameters for improving the structural and magnetic properties of ferrite films.     

Crystal anisotropy-dependent shear angle variation in orthogonal cutting of single crystalline copper

Shear deformation that dominates elementary chip formation in metal cutting greatly relies on crystal anisotropy. In the present work we investigate the influence of crystallographic orientation on shear angle in ultra-precision orthogonal diamond cutting of single crystalline copper by joint crystal plasticity finite element simulations and in-situ experiments integrated in scanning electron microscope. In particular, the experimental cutting conditions including a straight cutting edge are the same with that used in the 2D finite element simulations. Both simulations and experiments demonstrate a well agreement in chip profile and shear angle, as well as their dependence on crystallography. A series of finite element simulations of orthogonal cutting along different cutting directions for a specific crystallographic orientation are further performed, and predicated values of shear angle are used to calibrate an extended analytical model of shear angle based on the Ernst–Merchant relationship.     

Highly textured and strongly anisotropic TiB2 ceramics prepared using magnetic field alignment (9T)

Highly textured TiB₂ ceramics were prepared by slip casting an aqueous suspension in a magnetic field of 9 T, followed by sintering using Field Assisted Sintering Technology (FAST). Particle size refinement by ball milling improved both the degree of texturing and densification of the material (RD > 98 %). The sintered material exhibited a Lotgering orientation factor of 0.90, with the c-axis of TiB₂ oriented parallel to the magnetic field and FAST pressing direction. The texturing effect induced by the uniaxial pressing was negligible. The textured TiB₂ material exhibited a significant anisotropy in mechanical properties; the values of hardness and indentation elastic modulus measured along directions transverse to the c-axis of TiB₂ were 37 % and 13 % higher than the ones measured along the c-axis direction. Moreover, the specific wear rate of a surface of textured TiB₂ parallel to the field was one order of magnitude lower than a surface perpendicular to the field.