矿用履带式运输车在复杂开采条件下的应用

为了方便煤炭的运输，某矿使用了矿用履带式搬运车。履带运输车解决了轮式运输车在恶劣道路条件下不能行走的问题，这种履带车是一种新型的运输工具，其特点是体积小、转弯灵活、动力强大，可在不受场地限制的情况下轻松通过狭窄的地方，能有效解决山区、土壤、陡坡等恶劣条件下物料的运输问题，适合普通运输车辆无法通行的地方。介绍了矿用履带式搬运车的主要结构以及工作原理，并给出了实际应用中应注意的事项。     

煤峪口矿81010工作面煤层底板裂隙发育特征及防治

针对煤炭开采过程中出现的突水事故,采用RFPA数值模拟软件建立采动模型,对底板裂隙破断过程和声发射进行模拟,研究煤层底板采动裂隙扩展突水通道,结果表明:离断层越近,断层内水压导升高度越高,断层出现活化,裂隙扩展发育,最终贯通形成导水通道,在进行注浆改造后,单个钻孔的最大涌水量为8 m³/h,说明注浆加固防治水效果较好,能确保工作面的安全回采。     

No-Reference Video Quality Assessment using novel hybrid features and two-stage hybrid regression for score level fusion

This paper presents a novel No-Reference Video Quality Assessment (NR-VQA) model that utilizes proposed 3D steerable wavelet transform-based Natural Video Statistics (NVS) features as well as human perceptual features. Additionally, we proposed a novel two-stage regression scheme that significantly improves the overall performance of quality estimation. In the first stage, transform-based NVS and human perceptual features are separately passed through the proposed hybrid regression scheme: Support Vector Regression (SVR) followed by Polynomial curve fitting. The two visual quality scores predicted from the first stage are then used as features for the similar second stage. This predicts the final quality scores of distorted videos by achieving score level fusion. Extensive experiments were conducted using five authentic and four synthetic distortion databases. Experimental results demonstrate that the proposed method outperforms other published state-of-the-art benchmark methods on synthetic distortion databases and is among the top performers on authentic distortion databases. The source code is available at https://github.com/anishVNIT/two-stage-vqa.     

锌铝水滑石的制备及其在制革少铬鞣中的应用

通过共沉淀法制备了锌铝水滑石(ZnAl-LDH),采用XRD、FTIR、SEM对其结构进行了表征.将其配合用量为皮质量2％的铬粉(记为2％铬粉)应用于制革鞣制工艺中.考察了ZnAl-LDH制备时的金属源物质的量比、陈化时间对鞣制坯革收缩温度、鞣后废液中的Cr2O3质量浓度的影响.结果表明,ZnAl-LDH是尺寸在100～400 nm之间的片状材料.当n〔(Zn(NO3)2?6H2O)〕:n〔Al(NO3)3?9H2O〕=2.0:1.0,陈化时间为6 h时,制备的ZnAl-LDH-4具有优异的性能.与单独使用2％铬粉鞣制坯革相比,ZnAl-LDH-4(用量为皮质量的4％)配合2％铬粉鞣制坯革收缩温度由75℃提高到94℃,废液中的Cr2O3质量浓度由99.58 mg/L降低至46.98 mg/L,且加入ZnAl-LDH-4鞣制后,鞣后废液化学需氧量和生物需氧量均降低.     

Main trends on the simulation of the drying of refractory castables - Review

Refractory castables develop microstructures after curing that behave as partially saturated porous media. Upon heating (during its drying stage), the steam generated by the physical and chemically bond water can result in pore pressurization and explosive spalling. Numerical modeling can provide guidelines for designing safer heat-up profiles and also a better understanding of the mechanisms that lead to catastrophic damage. This work aims to review the fundamentals and models available, providing insightful thoughts on the current trends of the drying phenomena of ceramic compositions. The review also highlights that there are models better oriented to result in reasonable predictions of pore pressure values and others focused on a more accurate representation of the main physical phenomena that take place during heating. According to the findings, there are still various challenges to attain accurate models with high applicability capable of yielding safer and more efficient drying of refractory castables.     

氯乙烯变温吸附装置的研究

介绍了采用变温吸附技术对氯乙烯进行干燥脱水的工艺流程及运行效果,阐述了变温吸附装置运行过程中出现的问题及相应的解决方法。     

Investigation on thermal conductivity and mechanical properties of Si3N4 ceramics via one-step sintering

High thermal conductivity Si₃N₄ ceramics were fabricated using a one-step method consisting of reaction-bonded Si₃N₄ (RBSN) and post-sintering. The influence of Si content on nitridation rate, β/(α+β) phase rate, thermal conductivity and mechanical properties was investigated in this work. It is of special interest to note that the thermal conductivity showed a tendency to increase first and then decrease with increasing Si content. This experimental result shows that the optimal thermal conductivity and fracture toughness were obtained to be 66 W (m K)^-1 and 12.0 MPa m^1/2, respectively. As a comparison, the nitridation rate and β/(α+β) phase rate in a static pressure nitriding system, i.e., 97% (MS10), 97% (MS15), 97% (MS20) and 8.3% (MS10), 8.3% (MS15), 8.9% (MS20), respectively, have obvious advantages over those in a flowing nitriding system, i.e., 91% (MS10), 91% (MS15), 93% (MS20) and 3.1% (MS10), 3.3% (MS15), 3.3% (MS20), respectively. Moreover, high lattice integrity of the β-Si₃N₄ phase was observed, which can effectively confine O atoms into the β-Si₃N₄ lattice using MgO as a sintering additive. This result indicates that one-step sintering can provide a new route to prepare Si₃N₄ ceramics with a good combination of thermal conductivity and mechanical properties.     

Optimizing the stability and electrical transport properties of CeNbO4+δ-based oxide ceramics by regulating oxygen ion content

CeNbO_4+δ ceramics have attracted extensive research interest because of their unique mixed ion-electron transport characteristics and interesting structure-functional characteristics caused by the difference in oxygen ion content. Although the change of oxygen ion content brings rich redox properties, it also causes serious crystal transformation and abnormal electrical transport properties. In order to obtain stable structure and excellent electrical transport properties, the directional regulation of the oxygen ion content has been realized through introducing Al₂O₃ and high temperature aging. After 600 h of aging at 1073 K, the prepared composite ceramics not only obtain a stable structure without crystal transformation, but also show good negative temperature coefficient (NTC) thermistor characteristics in the temperature range of 473 K–1273 K, in which the linear fitting maximum Pearson's r of the relationship between lnρ and 1000/T can reach 99.97%. The proposed method provides a new thought for the design and application of high-temperature electronic ceramics.     

A novel multi-objective optimization method: Input values effect on responses (IVER)

In this study, a novel multi-objective optimization method based on the best effect of unique input (independent variable) values on responses (dependent variables) was proposed. The proposed method was compared with optimization using Derringer & Suich function that is still the most used. The comparison was made using the response values measured in real experiments and available in the literature. The advantages of the proposed method such as not needing the polynomial model aiming to predict the response values, no parameter selection problem, being able to offer optimum range instead of single optimum value, being suitable for use with existing experimental designs and being simple and interpretable were demonstrated as a result of comparison. It was also suggested how the proposed method will be effective according to experimental designs, and application for the users' application was presented.