Structure-conductivity relationship of PrBaMnMoO6-δ through in-situ measurements: A neutron diffraction study

The structural and electrochemical properties of the double perovskite-type oxide, PrBaMnMoO_6-δ, was investigated using neutron diffraction with in-situ conductivity measurement under a dry Argon atmosphere from 25 °C to 700 °C. A Rietveld refinement of the neutron diffraction data confirmed monoclinic symmetry in the P2₁/n space group. Rietveld refinement also confirms the unit cell parameters of a = 5.6567 (1) Å, b = 5.6065 (2) Å, c = 7.9344 (1) Å and β = 84.43° with reliable atomic positions and refinement factors (R-factors). Neutron diffraction data refinement shows two minor phases (<5%), an orthorhombic AB₂O₅ type phase of PrMn₂O₅ in the Pbam (No. 32) space group with unit cell parameters, a = 7.9672 (1) Å, b = 8.9043 (2) Å and c = 5.8540 (1) Å and a scheelite phase of BaMoO₄ in the tetragonal I4₁/a (88) space group with the unit cell parameters, a = b = 5.9522 (1) Å, and c = 12.3211 (2) Å. Morphological images revealed a porous and intertwined microstructure. In-situ conductivity measurement shows that the total conductivity of this material was 130.84 Scm^?1 at 700 °C.     

Characterization of the structure and properties of processed alumina-graphene and alumina-zirconia composites

The onset of hybrid alumina-based composites, which combines two or more nano-particles within the alumina matrix has already shown promising improvements in the matrix material. However, variations in mechanical properties including the optimum compositions that give improved properties faced with the development of alumina-based composites require further studies to understand the underlying mechanisms and synergistic effects of the nano-particle additions on the alumina matrix. In the current study, the structure and properties of Al?O?-graphene (0.5 wt%) and Al?O?–ZrO? (4 wt% and 10 wt%) composites fabricated via hot-pressing was studied as a baseline for multiple combinations. Even though the addition of 10 wt%ZrO? resulted in a 23% reduction in the grain size of the alumina matrix, the 4 wt%ZrO? addition resulted in a 14% increase in grain size as compared to the parent alumina matrix. X-ray diffraction analysis revealed that there was approximately 85% monoclinic (m-ZrO₂) vs. 15% tetragonal (t-ZrO₂) crystal structures in the A4ZrO? sample whilst the A₁₀ZrO? had approximately 93% m-ZrO₂ vs. 7% t-ZrO₂. The high-volume fraction of the monoclinic crystal structures in the A₁₀ZrO? accounts for the induced microcracks in the sample since the transition from the ductile-tetragonal to brittle-monoclinic is associated with the exertion of compressive stresses on the alumina matrix by the associated elastic volume expansion of m-ZrO₂. Also, the addition of 0.5 wt%graphene resulted in about 37% reduction in the grain size of the alumina matrix, and approximately 10% increase in hardness as a result of the distribution of graphene along the grain boundaries of the parent alumina matrix, which restricts grain coalescence and growth during processing. Furthermore, an increase up to 115% and 164% were observed in the fracture toughness (K_IC) with the inclusion of 0.5 wt%graphene and 10 wt%ZrO? respectively, which was primarily ascribed to the fine-grained microstructures and toughening mechanisms of the intergranular graphene and ZrO? particles.     

Mg-bearing quartz solid solutions as structural intermediates between low and high quartz

Glass powder samples of cordierite composition (doped with 8 mol% TiO₂) were heat-treated to produce a series of increasingly SiO₂-enriched Mg-bearing quartz solid solutions (Qss). The obtained materials were then analyzed by X-ray diffraction: Rietveld structural refinements revealed that Mg-bearing Qss phases possess trigonal symmetry and a compositionally dependent intermediate structural arrangement between those of low and high quartz. High-temperature diffraction measurements were performed up to 700°C to characterize the thermal expansion behavior of the crystals. At SiO₂-rich compositions, a reversible high-to-intermediate inversion of the quartz structure is observed, which shifts with increasing stuffing to lower temperatures than the conventional 573°C for pure quartz. Similarities and differences to the better-established Li-bearing Qss are discussed in the text.     

Influence of Se and Te substitutions at Tl-site of Tl(Ba,Sr)CaCu2O7 superconductor on the AC susceptibility and electrical properties

The Sr and Ba bearing Tl-1212 phase, Tl(Ba,Sr)CaCu₂O₇ is an interesting superconductor. The Sr only bearing TlSr₂CaCu₂O₇ is not easily prepared in the superconducting form. The Ba only bearing TlBa₂CaCu₂O₇ on the other hand does not show improvement in the transition temperature with elemental substitution. In this work the influence of multivalent Se (non-metal) and Te (metalloid) substitutions at the Tl-site of Tl_1-xM_x(Ba,Sr)CaCu₂O₇ (M = Se or Te) superconductors for x = 0–0.6 was studied. The samples were prepared via the conventional solid-state reaction method. XRD patterns showed a single Tl-1212 phase for x = 0 and 0.1 Se substituted samples. The critical current density at the peak temperature, T_p of the imaginary (χ”) part of the AC susceptibility (χ = χ’ +χ”), J_c-inter(T_p) for all samples was between 15 and 21 A cm⁻². The highest superconducting transition temperature was shown by the x = 0.3 Se-substituted sample (T_c-onset = 104 K, T_c-zero = 89 K, T_cχ’ = 104 K and T_p = 80 K). Te suppressed the superconductivity of Tl-1212 phase. The order of highest transition temperatures are as follows: Tl_1-xTe_x(Ba,Sr)CaCu₂O₇<Tl(Ba,Sr)CaCu₂O₇<Tl_1-xSe_x(Ba,Sr)CaCu₂O₇. This work showed that Se was better than Te in improving the transition temperature and flux pinning of the Tl-1212 phase. The roles of ionic radius of Se and Te on the superconductivity of Tl(Ba,Sr)CaCu₂O₇ are discussed in this paper.     

Synthesis and characterization of the novel nanostructured NiC carbide obtained by mechanical alloying

In the present work, a comprehensive study of mechanical alloying of Ni-carbon nanotubes (CNT) and Ni-Graphite equiatomic powder mixtures under the same technological modes has provided to reveal the features of using different types of carbon (CNT or graphite) as a charge component. The as-milled powders were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and magnetometric study. A novel nanoscale fcc NiC monocarbide was synthesized regardless the type of the charge used. According to the XRD study the formation of this phase takes place in two stages. A two-step carbide formation mechanism has been proposed. The associated changes in the nickel lattice, such as changes in the lattice parameter, lattice strain and residual stresses, which led to the formation of NiC monocarbide were also evaluated and discussed. Parameters of the electronic structure of NiC were calculated using the MStudio MindLab 7.0 software package with the experimental data on the crystal structure of the NiC phase obtained as input. Temperature dependencies of magnetic susceptibility of NiC synthesized have been studied up to 950 K. Carbides synthesized were found to be weak ferromagnets at the room temperature and their Curie temperature T_C ranges within 670 – 725 K. The calculated value of the magnetic moment per nickel atom (2.83μ_B) is higher than that of a bulk Ni (1.3μ_B). Likely, the observed increase of μ is caused by the presence of a certain amount of residual single-domain ferromagnetic Ni nanoparticles in the samples synthesized.     

Influence of high energy ball milling on structural,microstructural and optical properties of TiO2 nanoparticles

The influence of high-energy ball milling on structural, microstructural, and optical properties of TiO₂ by modifying the nanoparticle size was studied. Five samples were extracted at different milling times (0, 2, 4, 8, and 13 h). The average particle sizes estimated by dynamic light scattering (DLS) were 205, 155.8, 116.8, 82.9, and 82.7 nm at 0, 2, 4, 8, and 13 h, respectively. X-ray diffraction analysis confirmed progressive broadening of the peaks as the milling time elapsed. Besides, a correlation was found between d spacing and the average crystal size. The UV–Vis diffuse reflectance spectra of TiO₂ revealed a decrease in reflectance due to particle size reduction. Similarly, an alteration of the bandgap transition energy was presented, whose values gradually decreased from 2.966 eV to 2.861 eV for the sample without and with the maximum duration milling performed (13 h), respectively. Likewise, the SEM analysis showed a distribution in nanoparticle size that became more homogeneous and smaller average grain size as the milling duration was longer.     

Designing amorphous formulations of polyphenols with naringin by spray-drying for enhanced solubility and permeability

Naringin (NAR), a major flavanone (FVA) glycoside, is a component of food mainly obtained from grapefruit. We used NAR as a food additive to improve the solubility and permeability of hydrophobic polyphenols used as supplements in the food industry. The spray-dried particles (SDPs) of NAR alone show an amorphous state with a glass transition temperature (T_g) at 93.2 °C. SDPs of hydrophobic polyphenols, such as flavone (FVO), quercetin (QCT), naringenin (NRG), and resveratrol (RVT) were prepared by adding varying amounts of NAR. All SDPs of hydrophobic polyphenols with added NAR were in an amorphous state with a single T_g, but SDPs of hydrophobic polyphenols without added NAR showed diffraction peaks derived from each crystal. The SDPs with NAR could keep an amorphous state after storage at a high humidity condition for one month, except for SDPs of RVT/NAR. SDPs with NAR enhanced the solubility of hydrophobic polyphenols, especially NRG solubility, which was enhanced more than 9 times compared to NRG crystal. The enhanced solubility resulted in the increased membrane permeability of NRG. The antioxidant effect of the hydrophobic NRG was also enhanced by the synergetic effect of NAR. The findings demonstrated that NAR could be used as a food additive to enhance the solubility and membrane permeability of hydrophobic polyphenols.     

Inhibiting effect of heterogeneous cations aggregation enhanced by oxygen deficiency on glass formation of BaTi2O5 melts

Although remarkable development of titanate-based glasses has been achieved, challenge remains to elucidate the correlation between structure and glass-forming properties in these systems due to their complex structure that is inconsistent with the classic Zachariasen's model. In this work, we aim to correlate the structural evolution of titanate melts to their glass-forming ability (GFA). The prototypical material barium dititanate (BaTi₂O₅, BT2) melts with different GFA were rendered by controlled melting atmospheres, and the corresponding structural changes were determined using in situ high-energy synchrotron X-ray diffraction combined with empirical potential structure refinement and ab initio molecular dynamics. The results show that BT2 melt in reducing atmosphere shows poor GFA but that in oxidizing atmosphere presents good GFA. Structural analysis demonstrates the mean coordination number of [TiO_m] polyhedra is analogous in the melt under two different atmospheres but an enhanced heterogeneous cations aggregation takes place in the melt under reducing atmosphere, which is closely related to oxygen-deficiencies. Furthermore, we reveal that the enhanced heterogeneous cations aggregation promotes crystallization (and therefore hinders glass formation) through disordering the distribution of [TiO_m] and [BaO_n] polyhedra, changing the connectivity between these polyhedra, creating more crystal-like Ti-Ti clusters, and decreasing topological disorder of BT2 melt. Our work provides a new viewpoint to understand the GFA of titanates melt from structural heterogeneity beyond the previous perspectives that only focus on [TiO_m] polyhedra.     

Pressure-induced transparency of MgO,Al2O3, AlN,and cBN ceramics at room temperature

The in situ axial X-ray diffraction patterns of four ceramic powder samples (MgO, Al₂O₃, AlN, and cBN) that were compressed in a diamond anvil cell under uniaxial non-hydrostatic conditions were recorded. The microscopic deviatoric stress as a function of the pressure was determined from the X-ray diffraction peak broadening analysis: the curves increased approximately linearly with the pressure at the initial compression stage and then levelled off under further compression. Pressure-induced transparency was observed in all of the samples under compression, and the pressure at the turning point on the curves of the microscopic deviatoric stress versus pressure corresponded to the pressure at which the samples became transparent. Analysis of the microstructural features of the pressure-induced transparent samples indicated that the compression caused the grains to fracture, and the broken grains bonded with each other. We demonstrated that the ceramics’ pressure-induced transparency was a process during which the grains were squeezed and broken, the pores were close between the grains, and the broken grains were re-bonded under compression.     

Stabilization of 6H-Hexagonal SrMnO3 Polymorph by Al2O3 insertion

We demonstrate the structural evolution of polymorphic phases in Al₂O₃-inserted SrMnO₃ ceramics synthesized by solid state reaction. While the 4H-hexagonal phase is predominant in pure SrMnO₃ ceramics, a small amount of 6H-hexagonal polymorph is identified in addition to the primary 4H-hexagonal SrMnO₃ and the secondary hexagonal SrAl₂O₄ phases in the as-sintered ceramics, evidenced by x-ray diffraction and subsequent Rietveld refinement analyses. The existence of the 6H-hexagonal SrMnO₃ phase is corroborated using Raman spectroscopy. The chemical compositions and electronic structures of the Al₂O₃-inserted SrMnO₃ compounds are also examined using energy dispersive spectroscopy and x-ray photoelectron spectroscopy, respectively. The first-principles calculations reveal that there is no clear difference between the total energies of 4H- and 6H-hexagonal polymorphs regardless of the presence/absence of Sr and oxygen vacancies. Possible origins are discussed with the estimation of actual strain based on the refined lattice parameter of 6H SrMnO₃.