复杂环境下氧化铝储槽定向爆破拆除

在较为复杂的环境下,爆破拆除钢筋混凝土氧化铝储槽。该储槽自重大、呈圆形,内有4根立柱支撑下料漏斗。为使储槽顺利定向倒塌,通过爆破方案选择、参数确定,采取梯形切口和预处理以及安全防护和减振措施,使储槽爆破拆除获圆满成功。     

The role of microbial electrogenesis in regulating methane and nitrous oxide emissions from constructed wetland-microbial fuel cell

This study assesses a sustainable solution to greenhouse gases (GHGs) mitigation using constructed wetland-microbial fuel cells (CW-MFC). Roots of wetland plant Acorus Calamus L. are placed in biological anode to better enable anode microorganisms to obtain rhizosphere secretion for power improvement. Three selected cathode materials have a large difference in GHG emissions, and among them, carbon fiber felt (CFF) shows the lowest emissions of methane and nitrous oxide, which are 0.77 ± 0.04 mg/(m²·h) and 130.78 ± 13.08 μg/(m²·h), respectively. The CFF CW-MFC achieves the maximum power density of 2.99 W/m³. As the influent pH value is adjusted from acidic to alkaline, the GHGs emissions are reduced. The addition of Ni inhibits GHGs emission but decreases the electricity, the power density is reduced to 1.09 W/m³, and the methane and nitrous oxide emission fluxes decline to 0.20 ± 0.04 mg/(m²·h) and 15.49 ± 1.86 μg/(m²·h), respectively. Low C/N ratio reduces methane emission, while high C/N ratio effectively inhibits nitrous oxide emission. At the influent pH 8 and C/N = 5:1, the methane emission flux is approximately 10.60 ± 0.27 mg/(m²·h), and the nitrous oxide emission flux is only 10.90 ± 1.10 μg/(m²·h). Based on the above experimental results by controlling variable factors, it is proposed that CW-MFC offers an environment-friendly solution to regulate GHG emissions.     

基于电信号特征分析的电机故障诊断技术

介绍了电机故障诊断技术平台的组成,分析了电机常见故障下电信号的特征。利用宜昌和景洪工厂两台电机进行了实际对比测试,宜昌工厂电机定子电流特征频率在49.2Hz时表现出峰值-36.08dB,在50.8Hz时表现峰值则为-37.23dB,表明电机存在转子断条故障;景洪工厂电机在转子特征频率为113.51Hz时,出现峰值-58.47dB,表明电机存在静态偏心故障。经电机现场抽芯检查,验证了电机故障快速诊断平台给出的电机健康状态评估结果,证实了基于电信号特征分析的电机故障诊断技术的准确性。     

Fabrication method,dielectric properties,and electromagnetic absorption performance of high alumina fly ash-based ceramic composites

Mullite-Al₂O₃-SiC composites were in-situ synthesized through carbothermal reduction reaction of fly ash (FA) with a high alumina content and activated carbon (AC). The effects of sintering temperature, holding time, and amount of AC on the β-SiC yield, microstructure, dielectric properties, and electromagnetic (EM) absorption performance of the composites in the 2–18 GHz frequency range were studied. The results show that increasing the AC improves the porosities of the composites, with the highest porosity of 56.17% observed. The β-SiC yield varies considerably as the sintering parameters were altered, with a maximum yield of 23% achieved under conditions of 12 wt% AC, 1400 °C sintering temperature, and 3 h holding time. With a thickness of 3.5 mm, this composite has excellent EM absorption performance, exhibiting a minimum reflection loss (RL_min) of -51.55 dB at 7.60 GHz. Significantly, the maximum effective absorption bandwidth (EAB) reaches 3.39 GHz when the thickness is 3.0 mm. These results demonstrate that the composite prepared under ideal conditions can absorb 99.99% of the waves passing through it. Because of the interfacial polarization, conductive loss, and impedance matching of the heterostructure, the synthesized mullite-Al₂O₃-SiC composites with densities ranging from 1.43 g/cm³ to 1.62 g/cm³ demonstrate outstanding EM attenuation capabilities. Therefore, this study presents a remarkable way of utilizing fly ash to fabricate inexpensive, functional ceramic materials for EM absorption applications.     

Shock/expansion fan interaction with real gas effects for Earth and Mars atmospheric conditions

Numerical simulations are performed to investigate the real gas effects on shock/expansion fan interaction. Initial perfect gas simulations at low enthalpy capture the flow structures efficiently and outcomes are found to have excellent agreement with the analytical calculations. Furthermore, the simulations with the real gas solver for different enthalpies showed that the variation in enthalpy significantly changes the flow structures. It is observed that an increase in enthalpy leads to a decrease and increase in the postshock and postexpansion fan Mach numbers, respectively. Another important observation is the decrement in the peak pressure ratio with an increment in the enthalpy. These effects are noted to be more pronounced for Mars's environment due to the higher dependency of specific heat on temperature.     

Optical properties and radiation stability of SiO2/ZnO composite pigment prepared by co-sintering method

Thermal control coatings (TCCs) are an essential part of the thermal control systems in the spacecraft. Solar absorptance and emittance are the key performance parameters of TCCs. To develop an ultra-low solar absorption and stable inorganic TCCs for surface radiator, different TCCs were prepared by co-sintering ZnO and SiO₂ nanoparticles to form Zn₂SiO₄/SiO₂ pigment in this work, and the optical properties and radiation stability were systematically studied. It is found that the coating based on composite pigment has high reflectivity in the ultraviolet band and excellent optical performance possessing the low solar absorption of 0.06. In addition, the Zn₂SiO₄/SiO₂ coating demonstrates the highest proton and electron radiation stability because that SiO₂ between Zn₂SiO₄ particles acts as the relaxation center of the defects caused by radiation.     

Formation of Sn filled CNTs nanocomposite: Study of their magnetic,dielectric properties and enhanced microwave absorption performance at gigahertz frequencies

The Simplistic formation, advantageous configuration, non-colossal magnetoresistance and broadband absorption are important parameters for microwave absorbent materials. In this study, a core-shell nanocomposite comprising of Sn-filled carbon nanotubes (Sn/CNTs) was prepared by arc discharge method. The microstructure, morphology and surface composition of Sn/CNTs-based core-shell nanocomposites were characterized in detail. Sn/CNTs nanocomposite showed a magnetic signal due to the broken bonds and defects at interfaces in Sn/CNTs. The weak ferromagnetism was found to be helpful in improving magnetic permeability in the Sn/CNTs which confirms its role as a magnetic loss material under incident electromagnetic wave. Sn-filled CNTs revealed an appropriate value of dielectric constant, which plays an important role in impedance matching upon incident electromagnetic wave. The composite of Sn-CNTs and paraffin with a 50 wt % loading showed the lowest reflection loss (RL) of ?43.87 dB at 10 GHz, with a wide effective absorption band (RL ≤ ?10 dB) of 3 GHz in thickness of 2.3 mm. This enhanced performance is attributed to the combined effect of the conduction loss in one-dimensional core-shell architecture, the interfacial loss Sn-CNT interface, the magnetic loss due to defects-induced ferromagnetism in Sn shell, and in the carbon-containing atomic layers of CNTs.     

Mg gas infiltration for the fabrication of MgB2 pellets using nanosized and microsized B powders

MgB₂ superconductor pellets were synthesized through Mg gas infiltration method using nanosized- and microsized B powders. There was a marked difference in the superconducting properties of the two samples, particularly in the pinning force and dominant pinning mechanism. The microstructures of the samples were observed using HR-TEM and STEM-HAADF, and the results showed that the primary reason for the difference in the superconducting properties is the distribution of the nanosized second-phase particle MgO. Additionally, a feasible reaction model for the Mg gas infiltration method was established. Compared to the Mg liquid infiltration method, the gas infiltration showed better penetrability ability with a small amount of residual Mg. This study presents a novel synthesis process to fabricate an MgB₂ pellet with superior density and superconducting properties. This method can be used in multiple applications such as superconducting bearings, compact superconductor magnets, and magnetic shielding.     

基于Massive MIMO及频谱叠加的5G SA网络上行优化方法

大规模多输入多输出(Multiple-Input Multiple-Output, MIMO)可以有效提升5G SA网络的上行链路数据传输速率以及可靠性。针对5G SA网络上行链路速率和覆盖不均衡的情况,提出了基于大规模MIMO的分组算法,将发送信号矢量进行分组,组内采用最大似然检测,组外采用基于正交三角分解(QR分解)的干扰消除检测,并且结合5G频谱的叠加策略,在降低算法复杂度的同时,有效提升网络覆盖和速率。通过5G SA现网实测,通过MIMO降低分组数量能够提升分组检测性能,结合上行低频段频谱叠加策略能够有效提升5G SA网络上行覆盖30%,提升5G SA网络上行平均速率40%~80%,特别是弱覆盖边缘的网络速率,最高可达600%。     

Impedance matching optimization of SiCf/Si3N4–SiOC composites for excellent microwave absorption properties

SiC fiber reinforced ceramic matrix composites (SiC_f-CMCs) are considered to be one of the most promising materials in the electromagnetic (EM) stealth of aero-engines, which is expected to achieve strong absorption and broad-band performance. Multiscale structural design was applied to SiC_f/Si₃N₄–SiOC composites by construction of micro/nanoscale heterogeneous interfaces and macro double-layer impedance matching structure. SiC_f/Si₃N₄–SiOC composites were fabricated by using SiC fibers with different conductivities and SiOC–Si₃N₄ matrices with gradient impedance structures to improve impedance matching effectively. Owing to its unique structure, SiC_f/Si₃N₄–SiOC composites (A3-composites) achieved excellent EM wave absorption performance with a minimum reflection coefficient (RC_min) of ?25.1 dB at 2.45 mm and an effective absorption bandwidth (EAB) of 4.0 GHz at 2.85 mm in X-band. Moreover, double-layer SiC_f/Si₃N₄–SiOC with an improved impedance matching structure obtained an RC_min of ?56.9 dB and an EAB of 4.2 GHz at 3.00 mm, which means it can absorb more than 90% of the EM waves in the whole X-band. The RC is less than ?8 dB at 2.6–2.8 mm from RT to 600 °C in the whole X-band, displaying excellent high-temperature absorption performance. The results provide a new design opinion for broad-band EM absorbing SiC_f-CMCs at high temperatures.