Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

Computer analysis,design and simulation of horizontal ground heat exchangers

This paper presents a new computerized procedure for dealing with the design of horizontal ground heat exchangers (HGHE). The computer program is based on the transient model of coupled nonlinear partial differential equations governing heat and mass flow in soils. The model is two-dimensional and delineates the operation of ground heat storage with the HGHE and such phenomena as freezing/thawing and drying/rewetting of soil moisture. Comprehensive climatological data, such as ambient temperature, solar radiation, wind velocity, rainfall, snowfall, snow characterstics, and water vapour pressure is used to simulate conditions at the ground surface over any required length of time. The package can be applied to any geographical location by changing climatic and soil data input. The designer has the possibility of selecting any of 12 types of soils from sand to clay, 12 commercial heat pumps, nine different configurations of the HGHE, 16 plastic pipes for ground coils, and 13 ground coil fluids. The program, however, does not calculate the length of the HGHE but it evaluates the thermodynamic performance of a ground heat pump system and provides comprehensive data on thermal and hydraulic conditions in ground heat storage. The length of the ground heat exchanger is obtained from a line source theory model or from site dimensions and pipe spacing. Computed results for ground heat exchanger operation correlate fairly well with experimental data. Simulation of temperature and moisture content in the ground for natural conditions (no heat extraction/deposition) showed a fair agreement with field data. The entire computer program is user-friendly, interactive, menu-driven, and written in FORTRAN 77.     

面流消能近底紊动流速特性的研究(面流消能试验研究之一)

本文主要论述了面流消能五种典型流态近底紊动流速特性,总结出了近底时均流速和紊动强度沿程变化规律,提出了近底紊动流速可能出现的最大瞬时值及相应位置的计算公式。面流消能工程的下游防冲设计中考虑的主要水力参数之一是,消能段近底流速紊动可能出现的最大瞬时值及其相应的部位,但目前国内外研究成果较少。笔者通过水工模型试验重点研究了面流消能各典型流态近底流速及其紊动纵向分量沿程的变化规律,并提出了计算公式,为优化面流设计提供科学依据。     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

Optimization of metal-based multilayers for transparent heat mirrors

Multilayer calculations by conventional matrix methods for dielectricum/noble metal/dielectricum systems on glass have been performed. The aim has been to maximize the integrated parameters for solar transmission, T_sol, and transmission of visible light, T_eye We have found that Ag is superior for maximizing the transmittance over the narrow visible wavelength range owing to the low internal absorptance. When solar energy transmission is considered multilayers based on Au are the best choice for metal film thicknesses above 15 nm. For thinner films, Ag is still to be preferred.     

Open‐cycle OTEC systems with freshwater product: Effects of noncondensable gases on performance of condenser

An open‐cycle ocean thermal energy conversion (OC‐OTEC) system is one of the energy conversion methods used to generate electricity from ocean thermal energy. For the OC‐OTEC system, steam evaporated from the surface seawater due to flash evaporation drives the turbine. At that time, dissolved gas such as air is introduced into the low‐pressure system (OC‐OTEC system) as the noncondensable gas, which degrades the performance of condensation heat transfer. In this paper, a small‐scale OC‐OTEC experimental unit experimentally investigates the effect of noncondensable gas on the heat transfer performance in a condenser. The experimental results are discussed in comparison with theoretical estimation by the Sparrow–in method. It is shown that the condensation is occupied by heat and mass transfer near a condensation surface and that the condensation efficiency is affected by exhaust quantity of noncondensable gas at a relatively high concentration ratio of condensable gas. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(1): 29–35, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20179     

Discrete Modeling and Suggested Measurement of Heat Transfer in Gas-Solids Flows

This article presents a two-dimensional transient model for gas-solids flow and heat transfer through pipes using the coupled Computational Fluid Dynamics and Discrete Element Method approach. Numerical simulations have been conducted to examine the modification of fluid thermal structure due to the presence of particles in a pneumatic transport pipeline. Modeled results have demonstrated the key role of transversal motion of rebounding particles in the pipe cross section in altering fluid temperature. Further implementation of this modeling technique in air-drying processes is discussed and possible experimental methods for the measurement of in situ particle and fluid motion and temperature profile are cited.     

Immobilized α-amylase from Bacillus licheniformis: a potential enzymic time—temperature integrator for thermal processing

Biphasic and nth-order models were tested as to their usefulness to fit experimental inactivation data of Bacillus licheniformis α-amylase, immobilized on glass beads, and were discussed with respect to their suitability to characterize the considered enzymic system as a time—temperature integrator (TTI) to evaluate heat processes. Both isothermal and non-isothermal inactivation experiments were carried out. Model (kinetic) parameters (rate constant k, activation energy E_A and reaction order n) were estimated using a non-linear regression procedure. The results obtained, especially the activation energy of about 293 kJ mole^–1, indicated a potential use of this system as a TTI for heating processes in the temperature range of 96–108°C.